The gas inadvertently entered in the equipment is discharged and good sealing performance is ensured.　　There will be no insufficient liquid supply or other problems.P ā bna,　　The impeller channel reaches the outer edge.　　When the pump is not in use, the pump shall be lifted away from the water source in time to drain the accumulated water in the pump, especially in cold winter. Then put it in a dry place. Conditional users can also apply oil to the key parts of the water pump and add lubricating oil to the bearing to prevent parts from rusting. in additionPuerto Tejada, long-term operation cost and operation reliability.　　Auxiliary mixing or spraying device shall be equipped for easier operation. When the motor is submerged, there is no need to build complex ground protection and fixed devices, and the management is easier. The mixing impeller directly contacts the deposition surface and controls the concentration through the diving depth, so the concentration control is more free. Equipment directly submerged　　 To ensure the efficient operation of the submerged slurry pump, the clearance between the impeller and the front guard plate must be adjusted regularly to keep it between (.-mm). In addition to monitoring the flow and pressure during the operation of the pump, the motor shall not exceed the rated current of the motor. Monitor oil seal and bearing at any time

　　It will generate heat, but when it is serious, it will directly burn out the insulation; There may also be some faults in the ventilation system. At this time, it is necessary to check whether the fan of the submersible slurry pump is damaged or rotating　　 Disassembly of water pump: use a disassembly wrench to remove the water inlet joint by left rotation and use a disassembly cylinder to impact the conical sleeve at the lower part of the pump. After the impeller is loose, take out the impeller, and remove the guide housing. In this way, the impeller, guide housing, upper guide housing, check valve, etc. are unloaded in turn.　　The slurry pump should be larger. In addition to the existing industrial and mining applications of the vertical slurry pump, the submersible slurry pump can also be used as a mobile slurry pump,P ā bnaSmall deep well pump, such as sand pumping and prospecting on board; What are the advantages of the submersible slurry pump? The advantage of the submersible slurry pump is that it is convenient and flexible easy to operate and submergedtechnological innovation,　　Submersible slurry pumps generally need to use some composite materials for manufacturing when they are used, so that they can have good wear and corrosion resistance when they are used, and can be used to transport most of the media when they are used. Phreatic slurry　　 Assembly of rotor parts of submersible slurry pump Before assembly apply a layer of lubricating oil on the mounting surface to protect the shaft hole from damage.　　A large amount of lubricating oil is stored.

　　 To ensure the efficient operation of the submerged slurry pump, the clearance between the impeller and the front guard plate must be adjusted regularly to keep it between (.-mm). In addition to monitoring the flow and pressure during the operation of the pump, the motor shall not exceed the rated current of the motor. Monitor oil seal and bearing at any timeHow much is it,　　Extend service life. In fact, the submersible slurry pump is widely used in many lives, and there is a very important component water seal in the pump, which can separate the pump body from the motor, so it mainly plays a role in use　　During normal operation, the impeller of the slurry pump becomes tighter and tighter as it turns. The more it is used, the easier it will operate. However, if the slurry pump reverses, it will directly cause the impeller of the slurry pump to fall off. The slurry pump must be disassembled and then re inspected,P ā bnaSelf priming slurry pump wholesale, installed and tested.　　The direction of the differential pressure force is opposite, which can offset part of the axial force and prolong the service life of the bearing.P ā bna,　　During normal operation, the temperature of the motor is very high, some even as high as ℃. In this case,P ā bnaWear resistant slurry pump, it is easy to burn the motor and replace it with a new one. In fact, one motor burns out at this time. Don&#;t worry about replacing it. You must find out the cause of the motor&#;s heating, or　　Pump, sewage submersible pump and seawater submersible pump.　　According to the user&#;s requirements, the motor can add a variety of protection devices such as water inflow detection and overheating