There is also a vibration method to measure the vibration frequency of the pump, and the measurement is relatively simple. However, when using one method, the measurement results may have some errors. When using the submersible slurry pump, there are other vibration sources that will affect the measurement results,SuzhouRubber lining submerged slurry pump,SuzhouVertical multistage centrifugal pipeline pump, so it is actually the main　　At the same time, the supporting pipelines in the pump room shall be provided with vibration isolation elasticity.Suzhou,　　Static water level refers to the water level before the pump is started.　　First, let&#;s talk about the familiar vertical slurry pumps. Here we refer to ZJL and SP submerged slurry pumps. Strictly speaking, the submersible slurry pump is also a vertical slurry pump because its axis is basically vertical when it works, but it can be completely immersed in water when it runs, so it is a good choiceBileca,　　 important parts shall be marked in advance to avoid errors during resetting. The joint surface and vulnerable parts shall be properly kept to prevent damage.　　 A vent pipe is installed at the bottom of the pump, so that when the pump is buried underground, water will be injected into the bottom of the slurry pump through the vent pipe, so that a sand water mixture will be formed at the bottom of the slurry pump, so that the slurry pump can be started normally. The advantage of this approach is that even if　　When the water level reaches, the frequency of the frequency converter drops, and the slurry pump operates at a low speed. The higher the water level, the lower the speed; The lower the water level, the higher the speed. At the same time, the water level signal is transmitted to the control cabinet so that the operators can timely understand the liquid level. Through this control, the circulation in the slag slurry pool is basically unchanged

　　Extend service life. In fact, the submersible slurry pump is widely used in many lives, and there is a very important component water seal in the pump, so it mainly plays a role in use　　First, resulting in poor heat dissipation effect.Honest management,　　There is a difference between submersible slurry pump and sewage pump. Although the media conveyed by the two are not pure water and other media, the difference between slag slurry and sewage is still large. Let&#;s take a look at the difference between the two.　　For example, concentrate and tailings are treated in the concentrator, ash and slag are removed from the power plant,SuzhouHorizontal non clogging sewage pump, slime and dense medium coal are transported in the coal preparation plant, and slurry is transported in coastal river mining operations. The weight concentration of the treated slurry is: mortar %, ore slurry %; It can be operated in series according to the needs of users.　　 The secondary pump shaft seal of the two-stage series pump is (packing seal), and the startup of the series pump also follows the above method. Only after the first stage pump is started, the submersible slurry pump can open the outlet valve of the last stage pump (the opening size is based on the motor current of the first stage pump as the rated power

　　There are differences.market　　Rotate in the rolling direction until the friction between the impeller and the front guard plate stops, then use the adjusting bolt to move the rotor backward, record the forward and backward movement gap, evenly distribute it between the front and rear guard plates of the impeller until the gap between the impeller, the front guard plate and the rear guard plate is flat, stop, and tighten the two dust discs and fasten them on the shaft. adjustment　　The casing ground wire of QW (WQ) submersible non blocking sewage pump needs to be properly connected in strict accordance with relevant regulations. In order to ensure personal safety during operation, it is prohibited to do 'open' in the water of adjacent equipment and people during the operation of electric pump~ Or move in case of accident due to electric pump leakage.　　Work, no noise and vibration, and the site is cleaner.Suzhou, grind it to the oxide layer on the wire core gradually thin the rubber near the wire core, wipe the wire core with alcohol (or hydrochloric acid), wrap the insulation layer and sheath layer, and dry it naturally.　　What is the cause of pump overload.　　The type selection planning of submersible slurry pump has a great impact on its service life and operation stability. A scientific and reasonable type selection plan will affect whether the slurry pump can achieve efficient operation. The operating power of the slurry pump is very high and the loss is small. Service life of flow passage parts of pump