The submersible slurry pump is developed to adapt to the increasingly complex working conditions and facilitate the use of users. Its use mode is more flexible. The equipment has advanced structure, wide flow passage, strong sewage discharge capacity, excellent material selection and strong corrosion resistance. Suitable for conveying liquids containing solid particles, such as sandstone, cinder and tailings. So what are the requirements for its work? Let&#;s understand briefly.　　If the pressure in the local area is equal to or lower than the vaporization pressure corresponding to the water temperature in the flow process, the water will vaporize there and form many small bubbles mixed by steam and gas. The cavitation phenomenon is due to the bubble action when these small bubbles flow from the low-pressure area to the high-pressure area in the water pump,India,　　 Assembly of water pump: fix the shaft and water inlet joint on the mounting base, fix the impeller and conical sleeve on the shaft with the disassembly cylinder, and then install the guide housing and impeller In this way, the upstream casing and check valve are installed in turn.　　According to the user&#;s requirements, the motor can add a variety of protection devices such as water inflow detection and overheating, so that the product can operate safely for a long time under adverse working conditions.Tirgu Secuiesc,　　In addition to the method, materials shall be selected comprehensively according to the nature of corrosive medium, anti cavitation theory, corrosion mechanism of water pump and stress characteristics. In order to prolong the service life, protection should be done well, which should be a comprehensive optimization design method.　　The above introduction is about the cause ysis of the overload of the slurry pump. When we find these conditions when using the pump,IndiaHH slurry pump, we can check whether these reasons are the above. This is also a reminder that we need to maintain the pump during normal use. latent　　Therefore when the pump temperature is too high, you don&#;t need to panic. You can quickly troubleshoot according to the above-mentioned reasons so as to find out the root cause of the excessive temperature of the equipment in time, it has the advantages of simple structure convenient disassembly and maintenance, and convenient installation and use. The change of the sealing structure of the pump avoids the direct damage to the bearing after the mechanical seal is damaged, and the service life of the bearing has also been greatly changed.　　 estimated installation depth of pump M　　What?Statistics,　　In order to make the equipment perform better when it is used, but this also needs to be based on its working principle. It can not be adapted at will when it is optimized.　　The use of water pumps for agricultural drainage and irrigation can improve the ability of agriculture to resist natural disasters, increase production and ensure income, and provide material conditions for agricultural mechanization and water conservancy.　　Through the introduction, we learned that the submersible slurry pump can be used to transport slurry when it is used at ordinary times. The relationship between its special structure is very close, it also needs to be used in a correct way when it is used at ordinary times. Only in this way can

　　The purpose is to avoid water leakage of the pump, but the water seal may be damaged due to faults after being used for a period of time. Let&#;s learn how to replace the water seal.Latest consultation,　　 fold the three layers in half with self-adhesive butyl tape and gradually extend to the outside of the core. When winding, the tape shall be stretched twice,IndiaSubmersible sewage pump, and then the three layers shall be folded in half with PVC tape to ensure that the winding part is not less than mm, and the positions of the three joints shall be staggered for a certain distance in order to prevent short circuit.　　 check the cable and replace it if it is broken or broken to avoid leakage.　　The balance ring is also disassembled; Then remove the last stage impeller and the key back, and the middle section including the guide vane; in addition, remove the impellers, middle sections and guide vanes at other levels in the same way until the submerged slag slurryIndia,　　The water pump is not only the water supply for the city, but also the household water purifier used in our home. There is a with pump equipment to help us purify water. In any way, it can be divided into many types, each of which has different sizes, volumes and s. Therefore, many people believe that　　Submersible slurry pump In addition,IndiaPipeline pump, it must be used continuously during transportation. If there is an interval in the middle, so as to avoid the solidification of slurry in the pump when the operation is stopped.　　The submersible slurry pump and equipment can also choose to add some water inlet detection devices according to the actual use needs. The overheat monitoring devices are often used in a large amount in time, and the pump and motor of the equipment used in time are the same shaft, so