The standby submersible slurry pump shall roll the shaft / turn every week to make the bearing uniformly accept the static load and external oscillation. The building structure in the water pump room shall be reconstructed. Sound absorbing and isolating plates shall be installed around the wall and on the top of the machine room and fixed with light steel keel; The connecting holes between the machine room and other rooms are tightly blocked,　　When the pump is not in use,RashtBaigang deep well pump, the pump shall be lifted away from the water source in time to drain the accumulated water in the pump, especially in cold winter. Then put it in a dry place. Conditional users can also apply oil to the key parts of the water pump and add lubricating oil to the bearing to prevent parts from rusting. in additionRasht,　　 Pipeline single-stage single suction hot water pump. It is an IRG type single-stage single suction hot water pipeline pump with ring conveyor belt for high-temperature hot water boilers in metallurgy, chemical industry paper mills, timber, restaurants, bathrooms, hotels and other departments. The operating temperature is generally not more than ℃.　　Will be scrapped. In addition, since the length of the long shaft is generally fixed, the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. It is normal to use the equipment for a long time, for example, when the submersible slurry pump is used at ordinary times, air holes usually appearGoris,　　For example, in the market, for example, the sweeping pump, some of which have a depth of more than meters, if the installation is correct, the smooth oil is appropriate, the repair is timely, and the delivery life will be long the repair personnel should regularly repair the bearing components,RashtSubmersible slurry pump, check the condition of the bearings and the smooth oil, and regularly add or replace the smooth oil during the work, and the interval and write　　There are differences.

　　 for screws that are too tight or rusted for a long time, the nut can be lubricated with kerosene prepared in advance, or the nut can be gently knocked with a wooden hammer and then removed. This method can also be used in slurry pumps and other places.　　Submersible slurry pump Absorb silt and sand from rivers, lakes, reservoirs, fish ponds and power plants.　　Rotate in the rolling direction until the friction between the impeller and the front guard plate stops, then use the adjusting bolt to move the rotor backward record the forward and backward movement gap, evenly distribute it between the front and rear guard plates of the impeller until the gap between the impeller, the front guard plate and the rear guard plate is flat, stop, and tighten the two dust discs and fasten them on the shaft. adjustmentmarket price,　　 To ensure the efficient operation of the submerged slurry pump, the clearance between the impeller and the front guard plate must be adjusted regularly to keep it between (.-mm). In addition to monitoring the flow and pressure during the operation of the pump, the motor shall not exceed the rated current of the motor. Monitor oil seal and bearing at any time　　It will generate heat, but when it is serious, it will directly burn out the insulation; There may also be some faults in the ventilation system. At this time, it is necessary to check whether the fan of the submersible slurry pump is damaged or rotating　　 First, screw down the bolts on the side bearing pressure cap, and then remove the nuts used for the connection between the three parts: discharge section, stuffing box body and bearing body; Then screw off the round nut on the shaft, and successively install the bearing inner race, bearing gland and retaining sleeve

　　To repair the equipment. Submersible slurry pump is a machine used to transport liquid. It can be divided into many types according to different transport media. Then, when transporting some media with special properties, the equipment will be treated with corrosion-resistant and wear-resistant process. Only in this way can the equipment be improvedWelcome to inquire,　　When using the sand pump, be sure to pay attention to the steering divergence between the motor and the pump. The sand pump has an arrow on the pump to mark the main steering. After the power supply is connected, run the pump without load. Check whether the motor operates normally. During operation, be careful not to exceed the bearing on the pump support to avoid　　Stop the operation immediately under any of the following conditions: the current exceeds the rated value at the rated voltage; Under the rated head,RashtSubmersible sewage pump, the flow rate is much lower than that under normal conditions; Insulation resistance is lower than . megohm; When the dynamic water level drops to the pump suction; When the electrical equipment and circuit are out of specification　　 Cutting blades can be selected to cut some large block solid substances into pieces during use, so that blockage can be avoided during reuse.Rasht　　Schematic diagram of vertical slurry pump II. Why does the demand for submersible slurry pump increase greatly? From the perspective of market demand, although the absolute number of submersible slurry pumps has not exceeded that of vertical slurry pumps, it has a rapid development momentum, mainly due to the convenience and flexibility mentioned above; In addition, for submersible slurry pump　　 If the power cord is not well contacted, it will also lead to the burning of the motor.　　With water, you can start working.