All kinds of newly designed mechanical seals of submersible slurry pumps contribute greatly to the growth of market share.　　 It is also possible that the fan blades of the pump are few and the air volume is insufficient, resulting in poor heat dissipation effect.Zahedan,　　The development of pump industry in China has shown a very good trend in recent years. Of course,ZahedanBooster pipeline pump, this is also due to the accumulation of more than years of history. The evolution of pumps here is relatively diverse. So what we are going to introduce today is one of the more distinctive pumps - pipeline pump.　　Fourth, model selection parameters: outlet diameter, flow, dust, motor power, impeller speed,ZahedanCentrifugal slurry pump, pumping rate, we learned that the submersible slurry pump can be used to transport slurry when it is used at ordinary times. The relationship between its special structure is very close　　Through the introduction, but in fact it also needs to be used in a correct way when it is used at ordinary times. Only in this way can　　Moreover, because the length of the long shaft is generally fixed, it is often troublesome to install it. Therefore, when it is used later, the place where it operates will also be limited. If the equipment will　　Normal operation. The submersible slurry pump can transport the slurry with corrosive or solid particles, coal slurry heavy medium transportation and dredging the river. When the equipment is pumping sand, and the current will slowly increase during use. Well, we should choose

　　Schematic diagram of vertical slurry pump II. Why does the demand for submersible slurry pump increase greatly? From the perspective of market demand, although the absolute number of submersible slurry pumps has not exceeded that of vertical slurry pumps, it has a rapid development momentum, mainly due to the convenience and flexibility mentioned above; In addition, for submersible slurry pump　　Replace the motor shaft of the water pump.　　The development of submersible slurry pump is to adapt to increasingly complex working conditions, and its use mode is more flexible. And it fills a part of the gap in the application of slurry pump. When the submergence depth is deep and there is no better slurry outlet, that is, in the traditional slurry pumpTrustworthy,　　The of descending axial force can be used for slurry transportation in power plants,ZahedanCirculating hot water pipeline pump, hydraulic and other professions; The mechanical seal is tight and reliable, and the leakage probability does not exceed drops /min, which is mostly used to transport flammable, explosive, toxic, strong corrosive and valuable liquids or materials with high temperature, high pressure and low temperature.　　What should be paid attention to in the process? Let&#;s learn about the precautions for using the submersible slurry pump. When the equipment is in use, the pump itself generally needs to be placed on land for use, but its suction pipe needs to be placed in water　　If the submersible slurry pump cannot be installed and operated, the blank operation point can be supplemented.

　　The operating environment is different: the key difference between the submersible slurry pump and the vertical slurry pump lies in diving. During the operation of the vertical slurry pump some parts intrude into the pit and cannot completely invade the slurry; The submersible slurry pump can completely penetrate below the slurry level.Quality assurance,　　The above is the reason for the insufficient liquid supply of the water pump when it is in use, as well as the specific methods to deal with this situation. We should pay attention to the regular inspection of the equipment during normal use to ensure that it is in use　　 panning for gold and extracting iron sand.　　For example, it has a great impact on the impeller of the equipment itself. So how to detect whether the equipment has cavitation during use?Zahedan,　　The structure of the submersible slurry pump will be more intuitive. First, the equipment will use centrifugal force to drive the liquid from the impeller to the outer edge and obtain energy, and then leave the edge of the impeller at a higher speed　　So it has a process of water diversion and exhaust. There are usually two ways to inject water into equipment. One is to directly inject water into the pump chamber, and the other is to pump out the gas in the pump to establish a certain vacuum and introduce the water source.　　It needs to be replaced in case of damage, swelling and deformation, insufficient spring pressure, breakage, etc.