Frequently check whether the various mechanisms are operating normally and whether there is any noise. If a fault is found,DunakziGuide rail hydraulic lifting cargo elevator, scratches, there may also be a peeling paint spot, and a small rust will appear after a long time. Because most of these scars are small, they are easy to ignore. Therefore, check regularly, the engine compartment cover and its surroundings,DunakziFixed lifting cargo elevator, and once found, go to a professional beauty shop for processing.Dunakzi,Regular inspection and maintenance, elimination of hidden dangers, and troubleshooting are all good for improving work efficiency, prolonging the service life of equipment and ensuring the safety performance of the elevator.The design of the hydraulic lifting platform is unreasonable. When the designer designs the cylinder barrel and rod, if there is a problem with the design size and angle, then there will definitely be problems in the later stage. Therefore, it is necessary to confirm the technical strength of the manufacturer when working on a hydraulic lifting platform; what is the problem with the sound of the oil cylinder of the hydraulic lifting platform? Design drawings to make, the angle of the oil cylinder is slightly deviated, it will cause the friction between the cylinder barrel and the rod, which will cause the sound; the seal quality of the hydraulic lifting platform is different, and the use of different seals will also affect the sound of the oil cylinder, and the seal with excellent material The continuous friction between the parts and the cylinder wall will cause the sound to be very loud, and long-term wear and tear may scratch the oil cylinder and cause oil leakage, so when the hydraulic lifting platform is used, pay attention to ask the manufacturer what brand and material the seal is used; In some cases of mechanical running-in, it is not ruled out that the above three situations are normal, and there will still be noises. If there is no problem after investigation, then don’t worry. It’s just a running-in problem between mechanical parts. It will disappear naturally.Demba,The contact opening and closing of the travel switch of each safety device must be reliable, and the contact arc crater should be polished in time.Walking: assisted self-propelled, self-driving, and car modified.Precautions for using guide rail elevators Precautions for using guide rail elevators: It is strictly forbidden to overload, transport flammable and explosive products and other products.

It is strictly forbidden for personnel to take the freight elevator to go up and down floors and climb.Install two more standard sections. Use the theodolite to check and adjust the verticality of the guide rail frame so that the errors in two mutually perpendicular directions meet the requirements in Table . The above two parts are about the precautions for the installation of the elevator. If your work involves operation or It is to install a lift, everyone must pay attention to safety.System: explosion-proof electronic control system, remote control system, P IC system.production,The boxes and distribution boxes of the hydraulic lift are always kept clean, and the dust on the electrical equipment is cleaned in time.Ensure good power supply at the installation site, install a separate distribution box,DunakziOutdoor cargo elevator, and the leakage switch must meet the requirements for construction elevators when used in the distribution box. If the construction elevator installed is frequency conversion, the leakage switch should be adapted to the frequency converter when selecting the leakage switch .Hydraulic pump station: special pump station for domestic lifting platform, protection device outside the pump station imported from Italy: organ m type, mesh type, iron plate seal type.

Always check all wires and cables for damage. The damaged part should be bandaged and replaced in time.Create brillianceNaturally connect the motor to the lift. When connecting, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor and that the outer flanges of the two are parallel. If the concentricity is inconsistent, it will cause the motor shaft to break or the elevator gear to wear.Power unit adjustment, whether it is a scissor lift platform or a rail-type lift, is controlled by the power unit and the oil cylinder. The power unit is equipped with four outlet holes during production, which can be adjusted in size to increase or decrease the oil cylinder. Hydraulic oil flow, we can adjust the motor speed or the electro-hydraulic proportional valve to adjust the hydraulic oil flow; what factors will affect the lifting speed of the hydraulic lift oil pipe, the longer the hydraulic oil pipe, the longer the rise time. Therefore, the length of the oil pipe should be reduced as much as possible within the allowable range of the design; on the basis of adjusting the power unit, the size of the oil pipeline can also be adjusted and on the premise of ensuring that the equipment meets the normal requirements and safety, corresponding adjustment.The daily maintenance of the hydraulic lifting platform in normal use is essential, but even if there is normal maintenance on the equipment, any possible problem cannot be ignored, so in order to ensure that the process of using the hydraulic lifting platform for each operation What aspects do we need to check before operation? Today, the editor will give you a popular science.Dunakzi,It is strictly forbidden for personnel to take the freight elevator to go up and down floors and climb.What types of lifts are there? There are many types of this equipment, for example, it can be divided into fixed lifting devices and vehicle-mounted lifting devices according to the form of movement. The so-called fixed lifting means that it is generally installed in one place and fixed, and then the lifting operation can be carried out. This type of lifting equipment is generally used more on the assembly line. Some large-scale production lines need to move the material when loading materials. Lifting to a certain position, and then putting it into the production line for production, a special lifting device is required to be fixed at a certain position of the production line.In addition, during installation, it is strictly forbidden to use hammers, etc. to prevent damage to bearings or gears due to excessive axial force or radial force. Be sure to tighten the mounting bolts before tightening the force bolts. Before installation, clean the anti-rust oil on the motor input shaft the positioning boss and the connection parts of the elevator with gasoline or zinc and sodium water. Its purpose is to ensure the tightness of the connection and the flexibility of operation, and to prevent unnecessary wear and tear.