Compared with the vertical slurry pump, the application market is also larger. In addition to the existing industrial and mining applications of the vertical slurry pump the submersible slurry pump can also be used as a mobile slurry pump, such as sand pumping on board, prospecting, etc; Submersible slurry pump assembly workshop III. what are the advantages of submersible slurry pump　　Rotate in the rolling direction until the friction between the impeller and the front guard plate stops, then use the adjusting bolt to move the rotor backward, record the forward and backward movement gap, evenly distribute it between the front and rear guard plates of the impeller until the gap between the impeller the front guard plate and the rear guard plate is flat, stop, and tighten the two dust discs and fasten them on the shaft. adjustmentNetracona,NetraconaDeep well pump,　　 Transmission part all kinds of horizontal slurry pumps adopt the same series of transmission parts, including bracket and bearing components. The pump shaft has large diameter, good rigidity, short cantilever, and will not be bent and vibrated under bad working conditions. Heavy single row or double row conical roller is selected for the bearing according to the transmitted power　　It is longer and saves production cost. The whole industrial and mining system operates stably and will not affect the work of the whole industrial and mining system due to the operation of the pump. When the rotating speed of the submersible slurry pump cannot be changed and the lift is higher than the required equipment lift, the cut impeller is usually used. The cut isBebar,　　The effective power is also called output power, which is expressed by PE. It is the effective energy obtained in the pump by the medium liquid output from the pump in unit time.　　 bind the exposed copper wire to the cable core evenly, heat it with an electric iron, particle size, shape, acid concentration, alkali and other characteristics of the transported materials.

　　Do a good job of fixing to avoid the motor falling into the water and directly scrapping.　　Or nodular cast iron, vertically split, bolted. The pump body is connected with the bracket with bolts. The discharge outlet of the pump can be rotated and installed at intervals of ℃ and eight angles as required.　　The fruit is also bad; When the axial flow pump is used, its water output is relatively large, but the head is not too high, so the effect of using the submersible slurry pump in many plain areas is also relatively good; The water output and head of the mixed flow pump are actually derived from onewhere,　　The type selection planning of submersible slurry pump has a great impact on its service life and operation stability. A scientific and reasonable type selection plan will affect whether the slurry pump can achieve efficient operation. The operating power of the slurry pump is very high and the loss is small. Service life of flow passage parts of pump　　 It is also possible that the fan blades of the pump are few and the air volume is insufficient, resulting in poor heat dissipation effect.　　 To ensure the efficient operation of the submerged slurry pump, the clearance between the impeller and the front guard plate must be adjusted regularly to keep it between (.-mm). In addition to monitoring the flow and pressure during the operation of the pump, the motor shall not exceed the rated current of the motor. Monitor oil seal and bearing at any time

　　Start the priming pump. Moreover,NetraconaVertical heavy-duty slurry pump, due to the structural limitations of the submersible slurry pump, the motor needs to be placed on the water surface for use during operation, and then the pump needs to be placed in the water for use. Therefore, the submersible slurry pump must beFree consultation,　　Sex is different. Although the submersible slurry pump is widely used, the correct application is very important. Due to the limitation of the name of the slurry pump, some people outside the industry misunderstand this. In fact, the impurity pump, dredging pump, desilting pump, parallel belt drive, upper and lower belt drive, CV vertical belt drive, etc. A variety of speeds and variants are adopted to make the pump operate under the best working conditions. It has long service life and high operation efficiency, and can meet many kinds of harsh transportation conditions.　　 First of all, we need to choose equipment with formal certificates when making choices. We must avoid buying some obsolete or inferior products. And sometimes when the pump is in use, multiple pumps need to be used in parallel or standby pumps need to be prepared.Netracona,　　Work, and the site is cleaner.　　Basically, the reasons for the motor heating of the submersible slurry pump are the above items. If the motor heating occurs you can find the reasons from the above items. However, it must be noted that if the fault is caused by electricity,NetraconaSubmersible pump can pump sewage, people who do not know electricity should not repair it by themselves, so as to avoid people　　It, generator and market formed at the beginning of construction have gradually formed a certain scale after more than ten years of rapid development. In the early stage, in order to meet the needs of market development, generators and other mechanical and electrical products were collectively moved to the phase II market for operation. With a good business environment, water pumps and generators