In the mud pump, the axial force is mainly composed of the pressure difference force of the liquid effect on the impeller and the gravity of the whole rolling part. The effect direction of the two forces is the same, and the resultant force is the sum of the two forces. If the submersible slurry pump is equipped with an auxiliary impeller, the liquid effect is on the auxiliary impeller　　 Then replace the pulley and pump cover plate and tighten the fixing nuts.Taguergon,　　 Gradually disassemble the outlet pipe, gate valve and elbow with installation tools, disassemble the pump section by section and lift the pump out of the well. (if it is found that there is a jam during the lifting and removal process, it cannot be lifted by force, and the customer service points shall be moved up and down, left and right for safe lifting and removal)　　 the water pipe shall be provided with a gate valve to regulate the pump working point. The valve shall be installed as close to the pump outlet as possible. The pump unit greater than meters shall be provided with a check valve at the pump outlet. In case of sudden shutdown, it is necessary to prevent damage to flow passage components caused by water hammer.Minna,　　Submersible slurry pump In addition it must be used continuously during transportation. If there is an interval in the middle, it must be avoided that the interval is relatively long, so as to avoid the solidification of slurry in the pump when the operation is stopped.　　Wheel, mixing impeller and other main flow passage parts are made of high wear-resistant raw materials, which are wear-resistant, corrosion-resistant, non clogging, and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more complete desilting. There is no need to equip auxiliary vacuum pump, and the investment is lower.　　The above is about how to replace the water seal of Boshan submersible slurry pump. In addition to the water seal, other parts of the pump also need to be replaced in time when they are damaged. Moreover, some parts of the pump are relatively easy to be damaged, so we need to replace them regularly during use　　Check whether it needs to be replaced.

　　; In practical application, the submersible slurry pump is developing rapidly with its unique advantages. The vertical slurry pump needs to be fixed and installed in use, while the submersible slurry pump can be used directly without immersion, which is convenient and flexible.　　Whether the pipeline pump can absorb water and whether the pipeline pump has self-priming depends on the model of the pipeline pump. Most of the pipeline pumps have self-priming , and the pipeline centrifugal pumps with difficult self-priming can be checked according to the following methods. For longer use　　Submersible slurry pumps generally need to use some composite materials for manufacturing when they are used, so that they can have good wear and corrosion resistance when they are used, and can be used to transport most of the media when they are used. Phreatic slurryQuality improvement,　　 The gas inadvertently entered in the equipment is discharged and good sealing performance is ensured.　　After a certain value, water will also vaporize, which is called the vaporization pressure of water at this temperature.　　 Then replace the pulley and pump cover plate and tighten the fixing nuts.

　　Causes: there is air or gas accumulation in the water inlet pipe of the pump, or the bottom valve is not closed tightly, the water supply is not satisfied, the packing of the vacuum pump leaks seriously, and the gate valve or flap valve is not closed tightly.quality,　　 A trash trap can be added at the position of the water inlet pipe and used at an angle of degrees, and then a filter screen is installed in the trap to filter impurities for the second time so as to avoid the blockage of the submersible slurry pump during use.　　 Check the water pump: it is possible that the selection of the water pump is not matched with the motor, which makes the temperature of the motor too high after long-term operation; It is also possible that the working time exceeds the specified working time of the motor. At this time, the use time and times should be strictly limited, the correct thermal protection should be selected,TaguergonDrilling fluid slurry pump,TaguergonDeep well pump, and　　Wheel, corrosion-resistant, non clogging, and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range with high slag suction efficiency and more complete desilting. There is no need to equip auxiliary vacuum pump, and the investment is lower.Taguergon,　　Pressure. Therefore,TaguergonSingle stage slurry pump, a pressure gauge should be installed in this system to monitor whether the pressure meets the requirements.　　 First remove the pump from the engine.　　Will be scrapped. In addition, since the length of the long shaft is generally fixed, the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. The submersible slurry pump is developed to adapt to increasingly complex working conditions and facilitate the use of users. Its use mode is more