Next, the water seal,Banjo GoreSubmersible pump can pump sewage, lock ring and other parts need to be installed.　　 Then tighten the compression nut on the packing gland evenly to make the liquid leak out in drops, and pay attention to the temperature rise outside the packing chamber.Banjo Gore,　　Whether the pipe is blocked or the valve is not opened; D. whether the water pump is reversed.　　Some corrosive pastes containing crystals can also be transported. In the application range of slurry pump, about % are used in concentrators in the mining industry. Due to the poor working conditions of primary ore dressing, the service life of slurry pump in this section is generally low. Of course,Banjo GoreDouble suction slurry pump, abrasionNetzahualcoyotl,　　Adjustment. When using the submersible slurry pump, accessories will be used and some auxiliary measures will be taken to improve the overall performance of the equipment and ensure the stable use of the equipment. Many users do not pay attention to these things when using them, which will cause equipment problems and affect work efficiency. So we&#;re using　　However, there is also a disadvantage of using the auxiliary impeller sealing system, that is, it takes some energy on the auxiliary impeller of the submersible slurry pump which is generally about %. However, as long as the planning is reasonable, this part of the lost flow can be reduced. The slurry pump is mainly applicable to electric power, metallurgy and coal　　The water slurry pump is a widely used equipment. Many people are interested in the water diversion and exhaust method of the slurry pump equipment. Now let&#;s talk about the water diversion and exhaust method of the submersible slurry pump: the submersible slurry pump needs to pump out the water to form a vacuum, and then supply water,

　　Submersible slurry pump Use ultrasonic method to detect whether there is cavitation in the submersible slurry pump. This method is often convenient for re detection. Even if there is some noise in the surrounding environment, it will not affect the detection results. Therefore many pumps often have better measurement results when in use.　　 Assembly of water pump: fix the shaft and water inlet joint on the mounting base, fix the impeller and conical sleeve on the shaft with the disassembly cylinder, and then install the guide housing and impeller In this way, the upstream casing and check valve are installed in turn.　　The impeller of the submersible slurry pump may need to be disassembled for maintenance or repair during use. However, when we do not know the pump structure, we may make mistakes during disassembly. Let&#;s take a look at the correct disassembly of the impellerThe cost is reasonable,Banjo GoreCarbon steel explosion-proof pipeline pump,　　Commodity.　　 Protective packing of shaft seal the shaft seal pump shall regularly check the sealing water pressure and water volume, keep a small amount of cleaning water flowing along the shaft, regularly adjust the packing gland, check the packing and regularly replace the packing. The shaft seal water pressure and water volume shall meet the above (shaft seal inspection) requirements.　　 There is also a vibration method to measure the vibration frequency of the pump, and the measurement is relatively simple. However, when using one method, the measurement results may have some errors. When using the submersible slurry pump, there are other vibration sources that will affect the measurement results, so it is actually the main

　　With the arrival of midsummer and the intensification of the contradiction between supply and demand of kerosene, the power supply across the country has been tense again, which has driven the hot sale of it and generators in the phase II market. According to relevant data, in the second half of the year, there is still a large gap after China&#;s power balance.demand,　　 the water pipe shall be short and the cavitation allowance of the device shall be greater than that of the pump. It is recommended to use the reverse charging installation method when transporting residues with high weight concentration.　　The treatment method is as follows: first, check the circuit voltage to reduce the speed of the water pump.　　The purpose is to avoid water leakage of the pump, but the water seal may be damaged due to faults after being used for a period of time. Let&#;s learn how to replace the water seal.Banjo Gore,　　Pressure. Therefore, a pressure gauge should be installed in this system to monitor whether the pressure meets the requirements.　　Friction. Because if the surface of the pump is smooth when it is used, the equipment will consume less energy when it is used. Generally, it can only be opened or closed