Reinforcing phases such as reinforcing particles, short fibers and whiskers can be added to the solder to form composites.After spraying (throwing) derusting, it can not only expand the physical adsorption on the pipe surface, but also enhance the mechanical adhesion between the layer and the pipe surface. Therefore, spray (throwing) derusting is an ideal derusting method for pipelines. Generally speaking, shot blasting (sand) is mainly used for the inner surface treatment of the pipe, and shot blasting (sand) is mainly used for the outer surface treatment of the pipe. Several problems should be paid attention to in derusting by spraying (throwing).Tilgu Mures, the covering protection is not ideal, and there is no support, partly due to the excessive number of stacking layers and most coastal areas belong to marine climate, with large annual rainfall, high air humidity, ponding in the square pipe and the square pipe. The protection shall be: if the bare pipe or pipe needs to be stored for a long time, it shall be protected with an uncovered object from the beginning of storage to avoid rusting, layer aging, edge warping and other phenomena of the square pipe.When the vehicle is replaced with seamless square tube blank, the material is too soft to affect the requirements, so as to ensure the quality of parts and avoid wrinkles.Fonsar,When storing QB square pipe we need to select a suitable place. We need to think about many external factors, etc. Therefore such as the corrosivity of steel pipe, the place must be clean, dry and ventilated, where harmful gases appear, QB square pipe can not appear, weeds and other sundries should be removed in time, and the outer surface of steel should be kept clean. If there are acid, alkali, salt, etc. in the warehouse, if we can think about those higher metal products we can put them into the warehouse for very good retention. According to geographical conditions, there is a sealed warehouse, but the ventilation setting is excellent. The difference between QB square tube and seamless steel tube QB square tube is a kind of high-precision steel tube material after cold drawing or hot rolling treatment. QB square tube is mainly used to produce products of pneumatic or hydraulic components, such as air cylinder or oil cylinder,Tilgu Mures4x6 square tube, which can be seamless pipe or welded pipe, because there is no oxide layer on the inner and outer walls of QB square tube, no deformation under high pressure, high precision, high finish, cold bending, flaring and flattening without cracks. The chemical composition of QB square tube includes carbon silicon Si, manganese Mn, sulfur s, phosphorus P and chromium CR.: it refers to the processing of square tube,Tilgu MuresGalvanized grooved steel pipe, which places metal in a closed Jane and applies pressure at the end to extrude the metal from the specified die hole to obtain finished products with the same shape and size. It is mostly used to produce non-ferrous metal materials. Square tube ferrous metal, steel and non-ferrous metal. Before introducing the classification of steel, briefly introduce the basic concepts of ferrous metal, square tube steel and non-ferrous metal.Functional index analysis of qb square tube - mechanical function of plastic square tube. Solid bending, as the name suggests, the inner and outer rollers and the inner and outer walls of the pipe blank are compacted in both directions.

Steel for construction and engineering according to the classification of use without phase transformation or partial phase transformation of square tube: A. ordinary carbon structural steel; b. Low alloy structural steel; c. Steel reinforcement.Tensile strength of square tube (& sigma; b): the stress (& sigma;) obtained by dividing the force (FB) borne by the sample during breaking by the original cross-sectional area (so) of the sample during stretching, which is called tensile strength (& sigma; b), and the unit is nmm (MPA). It represents the large capacity of metal materials under tension.Functional index analysis of qb square tube - the load on the machine parts due to the great progress of strength is called the frontal collapse load. The power of destruction of qb square tube under the frontal collapse load is called the frontal collapse toughness.production,B. low alloy structural steel C. ordinary structural steel and high-quality steel for specific purposes (including high-quality steel)Spraying (throwing) derusting spraying (throwing) derusting is that the high-power motor drives the spraying (throwing) blade to rotate at high speed, so that the steel sand, steel shot, iron wire section, minerals and other abrasives can be sprayed (thrown) on the surface of the square tube under the action of centrifugal force, which can not only completely remove rust, oxides and dirt, but also the square tube under the violent impact and force of abrasives, It can also achieve the required uniform roughness.Among them, qb square tube is divided into: (a) by process & mdash& mdash; Arc welded square pipe, resistance welded square pipe (high frequency and low frequency), gas welded square pipe and furnace welded square pipe (b) are divided by weld & mdash& mdash; Straight seam welded square pipe, spiral welding

During the pushing process of spot welding and repair welding elbows, there will be thinning, so manufacturers usually use thick spot pipes. If thin raw materials are used, the products produced must be unqualified. Generally, there are about wires thinned. If the technology is not good or the drawn pipe is used, the thickness is significantly lower than the standard.High quality and low price,Oil drilling pipe (yb-) is a square pipe used for internal or external thickening at both ends of oil drilling. Steel pipes are divided into turning wire and non turning wire. Turning wire pipe is connected with joint, and non turning wire pipe is connected with tool joint by butt welding.Banded due to improper hot working temperature, that is, when the hot working stop forging temperature is in the phase zone (between, and ), ferrite precipitates in bands from austenite along the metal flow direction, and the undigested austenite is cut into bands. When it is cooled to a, the banded austenite is transformed into banded pearlite. This can be improved or eliminated by increasing the final rolling temperature, increasing the forging ratio, diffusion annealing and normalizing.A. square tube structural steel: (a) high quality carbon structural steel; (b) Alloy structural steel; (c) Spring steel; (d) Easy cutting steel; (e) Bearing steel; (f) High quality structural steel for specific purposes.Tilgu Mures,The other is designed with deformation angle, so the deformation angle & theta; It can accurately reflect the deformation degree of corners and edges. In the design process, considering the influence of dimensional accuracy and metal work hardening,Tilgu Mures25mm galvanized square pipe, the distribution of deformation angle is usually larger at the beginning and middle passes, and then gradually decreases. In the pass formed directly by arc intersection, the fillet part of the pipe blank cannot be filled with the pass, so the pass perimeter is different from that of the pipe blank. In order to ensure the dimensional accuracy, the fillet part of the pass needs to be corrected and calculated. Therefore, this method has higher design accuracy than other methods. However, due to the large amount of iterative calculation, this method is more suitable for pass design by computer. If you use a frame that deforms both horizontally and vertically, you can directly use the deformation angle & theta; Pass design.Derusting grade for the construction process of epoxy, ethylene phenolic and other coatings commonly used for square pipes, the surface of square pipes is generally required to reach near white grade (SA). Practice has proved that almost all oxide scale rust and other dirt can be removed by using this derusting grade, and the depth of anchor grain can reach ~ & mu; m, which fully meets the requirements of adhesion between layer and square pipe The shot derusting process can meet the technical conditions of near white level (SA) with low operation cost and stable and reliable quality.. fake and inferior square tubes are easy to fold. Folding is a variety of broken lines formed on the surface of square tubes, and this defect often runs through the longitudinal direction of the whole product. The reason for the folding is that the fake and shoddy manufacturers pursue the rate, the reduction is too large, folding occurs during the next rolling, the folded products will crack after bending, and the strength of the square tube will be greatly reduced.