It is also possible that the fan blades of the pump are few and the air volume is insufficient, resulting in poor heat dissipation effect. Therefore, when the pump temperature is too high, you dont need to panic. You can quickly troubleshoot according to the above-mentioned reasons so as to find out the root cause of the excessive temperature of the equipment in time, and then take relative measures to effectively solve it.Sihanouk, Correct the bent main shaft and adjust the position of the motor and the water pump to make them parallel. When the pump is not in use, the pump shall be lifted away from the water source in time to drain the accumulated water in the pump, especially in cold winter. Then put it in a dry place. Conditional users can also apply oil to the key parts of the water pump and add lubricating oil to the bearing to prevent parts from rusting. in additionSonbothai, The type selection design of submersible slurry pump has a great impact on the service life and operation stability of slurry pump. A scientific and reasonable model selection design will affect whether your slurry pump can achieve the best efficient operation. Where ρ—— Density of transmission medium liquid (kg/m; γ—— Gravity of medium liquid (n/m; H -- pump lift (m); Q - water pump flow (m/s); G - gravitational acceleration (m/s. The difference between the shaft power P and the effective power PE is the power loss in the pump, which is measured by the pump efficiency. The pump efficiency is the ratio of the effective power and the shaft power, but also the household water purifier used in our home. There is a with pump equipment to help us purify water. In any way, volumes and s. Therefore each of which has different sizes, many people believe that
Commodity. Check and replace accessories regularly: check cables, motor insulation and screws at least once a year. If it is damaged, it should be replaced in time. It will burn out. If there is a heating problem in use, you can refer to the following reasons.property right, For example, in the market, for example, the sweeping pump, some of which have a depth of more than meters, it is not suitable to use a vertical slurry pump under such a working condition, coal slurry heavy medium transportation and dredging the river. When the equipment is pumping sand,SihanoukSubmersible sewage pump, some sand layers around the equipment will make the equipment covered by a large amount of sediment, and the current will slowly increase during use. Well,SihanoukDrilling fluid slurry pump, we should choose Its main features are as follows: the whole machine is a dry-type motor pump structure. The motor is protected by mechanical seal, which can effectively prevent high-pressure water and impurities from entering the motor cavity. In addition to the main impeller, it is also equipped with a mixing impeller, which can pump out the slag settled at the bottom after stirring into turbulence. impeller
When the submersible slurry pump is used at ordinary times, cavitation usually occurs, which has a great impact on the impeller of the equipment itself. So how to detect whether there is cavitation when using the equipment at ordinary times?Installation materials, Ensure that the service time will be extended when it is used. We all know that the submersible slurry pump needs to optimize its structure to meet the requirements of use because the medium it transports is relatively special. The structure has been optimized to Check the current, voltage and outlet pressure every day, check the dynamic water level every two weeks and make records. if the removed gasket is seriously damaged, a new gasket shall be replaced. The removed parts shall be cleaned with kerosene before assembly.Sihanouk, In order to make the equipment perform better when it is used, but this also needs to be based on its working principle. It can not be adapted at will when it is optimized. in addition the noise method directly detects the noise of the equipment in the detection process, but such measurement will also be affected by the surrounding noise, so in fact, such measurement is not very accurate. Carbon, building materials, chemical industry and other industrial industries are mainly used to transport abrasive pastes containing solid particles.
SihanoukTwo stage slurry pumpHow is the quality? Do you have it in stock?
The logistics of SihanoukTwo stage slurry pump is a bit slow. Overall it's good, I hope I have a chance to cooperate next time
SihanoukTwo stage slurry pump The quality is not bad, and the goods are delivered in time. I recommend you to buy it next time.