When the submersible slurry pump works, the pump needs to be placed on land, the suction pipe needs to be placed in water, and the pump needs to be started. Due to special structural requirements, when the slurry pump motor is submerged in the water, the slurry pump and submerged slurry circulating pump need to be placed above the water surface, so they need to be fixed, otherwise the motor will fall into the water　　The of descending axial force can be used for slurry transportation in power plants, hydraulic and other professions; The mechanical seal is tight and reliable, and the leakage probability does not exceed drops /min, which is mostly used to transport flammable explosive, toxic, strong corrosive and valuable liquids or materials with high temperature, high pressure and low temperature.Shenzhen,　　Environmental conditions for normal operation of ordinary YLB motor:　　It is an auxiliary means of on-site monitoring. During the operation of the submersible slurry pump, the condition of its overflow parts is very important to the overall operation. In order to let everyone know more about the equipment, we will learn how to adjust the impeller clearance of the pump in this issue. I hope it will help you.Tagurgon,　　 confirm whether the pressure capacity of the pipeline meets the requirements, and conduct hydrostatic test if necessary.　　The above introduction is about the cause ysis of the overload of the slurry pump. When we find these conditions when using the pump, we can check whether these reasons are the above. This is also a reminder that we need to maintain the pump during normal use. latent　　 Pipeline layout: Firmly support the water pipe and drain pipe to prevent the force of the pipe from acting on the submersible slurry pump.

　　If the water leakage is serious, the broken pipe shall be dismantled and replaced. Lower the lift and press the nozzle of the water pump into the water for .m.　　 absorb fly ash and slime from various power plants.　　The effective power is also called output power,ShenzhenWQ submersible sewage pump, which is expressed by PE. It is the effective energy obtained in the pump by the medium liquid output from the pump in unit time.Promise and keep promise,　　The motor is scrapped. Moreover, because the length of the long shaft is generally fixed, the installation and use of the pump is troublesome, the blank operation point can be supplemented.

　　Moreover it is necessary to replace the new impeller in time for use.　　If the submersible slurry pump cannot be installed and operated, the leaked flammable, explosive and toxic liquid will cause fire, explosion and poisoning, and the consequences will be unimaginable.Installation material list,ShenzhenVortex pump and pipeline pump,　　The equipment is integrated with the oil cooler, with compact layout. The water pump meets the modular and integrated design requirements of diesel engine parts. The joint surface with oil cooler adopts rubber sealing method, which has good sealing effect. Submersible slurry pump is a kind of solid-liquid mixing medium with the help of centrifugal force　　The submersible sewage pump is a kind of pump product which is connected with the motor and works under the water at the same time. Compared with the general horizontal pump or vertical sewage pump, the submersible sewage pump obviously has the following advantages: Compact structure and small floor area. Submersible sewage pump is submerged　　The of descending axial force can be used for slurry transportation in power plants, hydraulic and other professions; The mechanical seal is tight and reliable, and the leakage probability does not exceed drops /min, which is mostly used to transport flammable, explosive, toxic, strong corrosive and valuable liquids or materials with high temperature, high pressure and low temperature.Shenzhen,　　The hardened mud layer collapses after softening, we need to know that submersible pumps generally operate in water. In fact, and their impellers are generally in a closed state. However, one of the media conveyed by sewage pumps may　　 There may also be mechanical failure of the pump such as serious damage to the bearing of the pump, so that the bore will be 'swept' when the stator and rotor rub against each other, or the impeller will be stuck due to impurities such as water and grass when the pump pumps water