Check the protective cable condition of the cable guide frameKnowledge of pressure lifting platforms, boarding bridges, mobile elevators, and more is available in Jiuheng, Jinan. We sincerely welcome colleagues from all walks of life to visit and inspect the factory, cooperate and negotiate, and seek common development. The following maintenance and upkeep are required for the lifting cargo elevator: Maintenance and upkeep: Maintenance and upkeep should be carried out by the equipment operator or full-time personnel of the operating unit. The equipment maintenance and upkeep unit is responsible for supervising and reviewing the maintenance content. The main content of maintenance and upkeep is summarized as follows:; quot; Cross operation method; quot;: Clean, tighten,OberhausenSelf propelled scissor fork type lifting platform truck, smooth, adjust, and prevent corrosion. Before and at the end of each shift, to minutes before and after each day, inspect all parts and components of the equipment to ensure they are normal. Apply oil smoothly according to rules, pay attention to the sound of mechanical operation, and do a good job in cleaning and handover to achieve the goal of clean appearance and normal operation of the equipment. Maintenance and handover records should be made in a fixed form and used for managementOberhausen,Emergency stop: Press the emergency button switch to raise or lower the machine.Check the relative orientation between the cable support wall and the cable guide frameMahebourg,Check the fastening status of the wall bracket, support rod, and bolts and retaining rings between the lifting cargo elevator and the bridge. If they are loose or displaced, they should be checked and tightenedQuarterly maintenance: Check the items checked each monthTransfer of goods between floors of rooms, restaurants, and restaurants. The low height is between -mm, especially suitable for workplaces that cannot excavate pits. And there is no need for upper lifting points, with diverse forms (single column, double column, four column), stable equipment operation, economic and convenient goods transmission, and difficult to solve narrow spaces that cannot reach the requirements. A customized delivery platform can be created, and the product hydraulic system is equipped with anti fall, upper and lower door interaction, and operation buttons can be set on each floor and lifting platform workbench to achieve multi-point. The product has a sturdy structure, a large load-bearing capacity smooth lifting,OberhausenAluminum alloy lifting platform single column, simple and convenient installation and maintenance, making it an ideal and economical cargo conveying equipment for replacing elevators between low floors. The lifting stage device is mainly responsible for data processing of the operation mechanism and work bar of the vehicle, and is suitable for the electric control system of the self lifting stage lifting platform. The main sensors in the electric control system include angle sensors, long angle sensors, dual axis inclination sensors, and energy saving of the oil cylinder system.

Check the wear and clearance condition of the guide wheel of the cargo elevatorAccording to calculations, when the support points of the beam type components are located along the length of /L on both sides, the vibration resistance is relatively small making it easy to obtain resonance and vibration effects with larger amplitudes. The geometric shape of the structure on the lifting foundation is similar to a long beam type component, and the structure is complex. Therefore, two support points should be taken on each side for time treatment.Check the relative orientation between the cable support wall and the cable guide frameManagement Department,When disassembling the hydraulic oil tank filler cap, inspection hole, hydraulic oil pipe and other parts, it is necessary to avoid dust during the system oil passage. The disassembled parts must be thoroughly cleaned before opening. When disassembling the hydraulic oil tank filler cap, first remove the soil around the tank cap. After loosening the tank cap, remove any remaining debris from the joint area (do not rinse with water to prevent water from seeping into the tank). Only after confirming cleanliness can the tank cap be opened. When using materials and hammers, materials that do not remove fiber impurities and specialized hammers with rubber attached to the surface should be selected. Hydraulic components and hydraulic hoses should be carefully cleaned, dried with high-pressure air, and then assembled. Choose a well packaged filter element (the inner packaging is damaged, although the filter element is intact, it may also be unclean). When changing the oil, clean the filter at the same time. Before installing the filter element, carefully clean the bottom dirt inside the filter housing with materials.Attention: Abnormal meshing of gear teeth should be avoided: uneven rolling of the rollers should be avoided; Avoid diagonal orientation of the guide rollers; It should be avoided that the guide rollers are kept at the same time for a long time; The above abnormal phenomena can lead to rapid wear and even scrapping of gears, racks, rollers and guide rails. If adjusted more carefully, it will be more beneficial for the service life of the elevator.When disassembling the hydraulic oil tank filler cap, filter cover, inspection hole, hydraulic oil pipe and other parts, it is necessary to avoid dust during the system oil passage. The disassembled parts must be thoroughly cleaned before opening. When disassembling the hydraulic oil tank filler cap, first remove the soil around the tank cap. After loosening the tank cap, remove any remaining debris from the joint area (do not rinse with water to prevent water from seeping into the tank). Only after confirming cleanliness can the tank cap be opened. When using materials and hammers, materials that do not remove fiber impurities and specialized hammers with rubber attached to the surface should be selected. Hydraulic components and hydraulic hoses should be carefully cleaned, dried with high-pressure air,OberhausenSelf-propelled lifting platform, and then assembled. Choose a well packaged filter element (the inner packaging is damaged, although the filter element is intact, it may also be unclean). When changing the oil, clean the filter at the same time. Before installing the filter element, carefully clean the bottom dirt inside the filter housing with materials.

The surface of each part of the brush should be kept clean, and the brush pressure should be adjusted to ensure that its area is not less than %.new product,Check if the orientation of the upper and lower limit blocks on the guide rail frame is correctOutbound call form: Outbound call boxes are pre embedded or installed in a column style on the wall or ground near the parking floor above and below the platform,Check the clearance of the ball bearing and the wear of the suspension wheel guide wheel. If the roller is worn, it is necessary to adjust or replace it. If the elevator bearing is worn, replace the guide wheel or bearingLeakage occurs due to looseness, vibration, and the influence of heat on the sealing surface and pipe joints of the machine; Some casting, processing and other defects are difficult to detect during assembly and debugging, but due to vibration and impact during the operation process, these defects are exposed, manifested as oil (water) leakage. Therefore, leakage is prone to occur during the running-in period. Poor, oil (grease) is not easy to form a uniform oil film on the friction surface to prevent wear. This reduces efficiency and causes early abnormal wear of the components. In severe cases it can cause scratches or bite on the friction surface of precision fitting, leading to the occurrence of faults.Attention: Abnormal meshing of gear teeth should be avoided: uneven rolling of the rollers should be avoided; Avoid diagonal orientation of the guide rollers; It should be avoided that the guide rollers are kept at the same time for a long time; The above abnormal phenomena can lead to rapid wear and even scrapping of gears, racks, rollers and guide rails. If adjusted more carefully, it will be more beneficial for the service life of the elevator.