Yes, such mechanical faults will cause the stator winding of the pump to be burnt out.　　If there is a standby pump it is recommended that the two pumps be used in turn. When the equipment is in use, it can pretend that a filter screen plays the role of filtration, so as to avoid a lot of impurities entering the equipment and causing pump jamming.Iseron,　　For the pipeline pump in the workshop, it is necessary to consider whether the pipeline pump is worn to a certain extent due to inadequate maintenance, but the performance of the pipeline pump is degraded. In case of abnormal water absorption during installation, check the motor during installation, and check the motor wiring and speed,　　Pressure. Therefore, a pressure gauge should be installed in this system to monitor whether the pressure meets the requirements.Zenica,　　 We also need to make choices according to local conditions when we make purchases at ordinary times. For example, the head of the centrifugal pump itself is relatively high, but its water output is not very large when it is used so it is effective when it is used in many mountainous areas　　Submersible slurry pump it fills the gap in the application of slurry pump. When the submergence is deep and there is no good mud outlet, that is, the traditional slurry pump cannot be installed and operated, and the submersible slurry pump can supplement this part of the blank work point.　　The above is the reason for the insufficient liquid supply of the water pump when it is in use as well as the specific methods to deal with this situation. We should pay attention to the regular inspection of the equipment during normal use to ensure that it is in use

　　 During the installation of smooth bearing components, if the installation is correct, the smooth oil is appropriate, the repair is timely, and the delivery life will be long, the repair personnel should regularly repair the bearing components, check the condition of the bearings and the smooth oil, and regularly add or replace the smooth oil during the work, and the interval and write　　 the experimental water shall meet the relevant process requirements.　　Fourth, model selection parameters: outlet diameter,IseronWear resistant slurry pump, flow, dust, motor power, impeller speed, pumping rate, maximum particle and weight.Superior quality,　　The of descending axial force can be used for slurry transportation in power plants,IseronTwo stage slurry pump, hydraulic and other professions; The mechanical seal is tight and reliable, and the leakage probability does not exceed drops /min, which is mostly used to transport flammable, explosive,IseronBooster pipeline pump, toxic, strong corrosive and valuable liquids or materials with high temperature, high pressure and low temperature.　　As an emerging product the submersible slurry pump has many advantages, especially filling the gap in the application conditions of the traditional horizontal and vertical slurry pumps. At present, the application of the submersible slurry pump is gradually becoming more and more widespread, and the market recognition is continuously improving, especially meeting the needs of deep-water sand pumping and dredging. At present, the depth can reach meters.　　Water pump is a kind of machinery that pumps energy liquid. It is a machine that converts the mechanical energy of the prime mover into the potential energy of the pumped liquid. Driven by power machinery, it can pump liquid from low to high or far away to serve production.

　　Circumference. In the application of slurry pump, we must pay attention to reasonable design, correct calculation and appropriate type selection, which are very important. In addition to the main wheel, a set of stirring impeller is added at the bottom of the product, which can spray the precipitated slag into a mixture of water and solid particlesanalysis,　　 Selection of pipeline diameter: the selection of pipeline shall consider the one-time purchase cost, long-term operation cost and operation reliability.　　 With protection . cf fire control cabinet integrates many electrical components, which can form a three-dimensional protection for the fire pump, including voltage overvoltage and undervoltage protection, current overcurrent and undercurrent protection, overload protection, overheating protection, etc. this　　 bind the exposed copper wire to the cable core evenly, heat it with an electric iron, and infiltrate tin evenly.Iseron,　　Ensure that the service time will be extended when it is used. We all know that the submersible slurry pump needs to optimize its structure to meet the requirements of use because the medium it transports is relatively special. The structure has been optimized to　　Stop, then tighten the bearing seat, if there is a problem with the clearance in the future use, loosen the support clamp first, and say that the nut is loose　　The input quantity is related to many factors such as the rotating speed of the submersible slurry pump, the bearing standard, the continuous working time, the number of stops and starts of the pump, the surrounding environment and the working temperature. Therefore, it is necessary to gradually accumulate the experience and add smooth oil in a reasonable and timely manner.