During adjustment, firstly loosen the support cover,Tangerang Carbon steel explosion-proof pipeline pump, then compress the nut, and then loosen the bearing seat. After adjusting the screw, tighten the compression nut of the bearing seat evenly to make the assembly move towards the pump head. It is necessary to turn the trolley while tightening until the plate does not move. Rotate according to the pump operation　　Avoid airborne sound transmission; Ensure the airtightness of machine room doors and windows. The water pump is equipped with a sound proof cover and an exhaust fan is added inside the cover to ensure the ventilation of the equipment. At the same time, the inlet and outlet of the sound proof cover are equipped with silencing equipment. A vibration isolation platform is installed at the bottom of the water pump for foundation vibration reduction to isolate the vibration generated during the operation of the water pumpTangerang ,　　In order to meet the use requirements of slurry pumps in different industrial fields and working conditions, we have continuously carried out research, development and improvement, so that we have different series,Tangerang QJ submersible pump, each series has a variety of specifications and models, and different series of products have different performance and s. Let&#;s learn about it below　　 in addition, the noise method directly detects the noise of the equipment in the detection process, but such measurement will also be affected by the surrounding noise, such measurement is not very accurate.Tessaoua,　　In fact,Tangerang Sewage pump diving, when the submersible slurry pump is blocked during use it will not only have a certain impact on the working efficiency of the equipment during operation, but also cause serious damage to the equipment itself, so it is also a reminder that we are using it too　　Function of shaft seal of submersible slurry pump: the main of shaft seal is to prevent high-pressure liquid from leaking out of the pump and prevent air from entering the pump.　　Function of shaft seal of submersible slurry pump: the main of shaft seal is to prevent high-pressure liquid from leaking out of the pump and prevent air from entering the pump.

　　What is the solution to this situation?　　Therefore, it can be directly installed in the sewage tank without building a special pump room to install pumps and machines which can save a lot of land and infrastructure costs.　　It is also necessary to clean the ventilation duct to avoid blockage.Quotation sheet,　　If there are sundries blocked, the pump will not be filled with water. When this happens again, technicians need to properly adjust the liquid level in the pump sump to a proper height, and check the impeller. In case of damage or aging, it needs to be replaced in time,　　 The pump body (can not) bear the pressure from the outlet pipeline system. The standby pump in the warehouse should rotate (/ times a week to make the shaft bear the load and external vibration evenly. The belt CR drive is that the motor is on the (right) side of the pump from the inlet of the pump.　　The submersible slurry pump shall be shut down for inspection in time in case of machine problems during operation, and regular maintenance shall be done. The equipment will not be used after burning out, which will cause certain economic losses to us.

　　Body. So that the pump can realize high concentration transmission without auxiliary devices. The unique sealing device can effectively balance the pressure inside and outside the oil chamber, so that the pressure at both ends of the mechanical seal can be kept balanced, which maximizes the reliable operation of the mechanical seal and greatly extends its service lifeHow much is it,　　Its main features are as follows: the whole machine is a dry-type motor pump structure. The motor is protected by mechanical seal, which can effectively prevent high-pressure water and impurities from entering the motor cavity. In addition to the main impeller, it is also equipped with a mixing impeller, let&#;s talk about the difference between WQ and QW sewage pumps.　　Turn on the power supply type fool operation; It has a wide range of applications. In many cases, it belongs to a portable workstation, because it does not need too many auxiliary facilities.Tangerang ,　　So it has a process of water diversion and exhaust. There are usually two ways to inject water into equipment. One is to directly inject water into the pump chamber, and the other is to pump out the gas in the pump to establish a certain vacuum and introduce the water source.　　 add water with manual pump. Some pump owners have their own hand pumps. They can also buy or manufacture their own small hand pumps. The gate valve shall be installed at the water inlet. After closing the valve, inject a small amount of water into the water compressor to divert water. When the hand pump discharges water, it means that the pump is full　　In this way, a smooth surface can be formed on the surface.