When using the sand pump,EsfarayanZD slurry pump, be sure to pay attention to the steering divergence between the motor and the pump. The sand pump has an arrow on the pump to mark the main steering. After the power supply is connected, run the pump without load. Check whether the motor operates normally. During operation, be careful not to exceed the bearing on the pump support to avoid　　 The standby submersible slurry pump shall roll the shaft / turn every week to make the bearing uniformly accept the static load and external oscillation. The building structure in the water pump room shall be reconstructed. Sound absorbing and isolating plates shall be installed around the wall and on the top of the machine room and fixed with light steel keel; The connecting holes between the machine room and other rooms are tightly blocked,Esfarayan,　　 when the deep well pump is put into water for use,EsfarayanVertical centrifugal slurry pump, hoist or electric hoist) used shall be greater than the weight of the submersible pump, and enough space shall be reserved. A wood that is tied to the wellhead with a rope　　 Moreover, the processes of these two pumps are also different and the sewage pump can generally be adjusted. Submersible pumps are generally used in some special or other places.Mumbai,　　The first stage impeller of the pump is disassembled; It is also necessary to screw down the connecting nut between the water absorption section and the bearing body and the bolt on the bearing pressure connection, so that it is convenient for us to disassemble the bearing parts; When the shaft is pulled out from the suction section, the fixing nut on the shaft shall be　　Auxiliary mixing or spraying device shall be equipped for easier operation. When the motor is submerged,EsfarayanVertical slurry pump, there is no need to build complex ground protection and fixed devices, and the management is easier. The mixing impeller directly contacts the deposition surface and controls the concentration through the diving depth, about % are used in concentrators in the mining industry. Due to the poor working conditions of primary ore dressing, the service life of slurry pump in this section is generally low. Of course different minerals, abrasion

　　Submersible slurry pump shaft seal type: packing, packing and auxiliary impeller seal, etc.　　Extractable.　　There will be no insufficient liquid supply or other problems.Installation works,　　There are differences.　　In the application of pumps, the first thing we think of is water. Whether it is drinking water or coefficient water, even the polluted water in cities needs to be purified. All these require its equipment to provide services for us. Without pumps, our basic survival is a problem.　　 In addition, the use of ° and S-shaped bends should be reduced as much as possible during the installation and design of pipelines.

　　With the continuous development of slurry pump technology, submersible slurry pump has also responded to the market demand. At the same time, this type of pump is especially suitable for the depth where the vertical slurry pump cannot operate. Pay attention when using the equipment. The submersible slurry pump can operate if its depth is less than m, but it exceedsDiscount,　　 Structural features and working principle qsz submersible slurry pump is a coaxial integration of water pump and motor. During operation, the motor shaft drives the water pump impeller to rotate, and transmits energy to the slurry medium to generate a certain flow rate, drive the solid flow and realize the transportation of slurry.　　The resistance loss in the lifting pipe and the resistance loss of the water delivery pipe after the outlet of the pump base.　　 Prepare tools and materials: a set of metric box / open-end wrench, bearing puller (commonly known as triangle puller), magnetic dial indicator, outside micrometer, caliper, feeler gauge, square ruler, copper bar, screwdriver with handle, hammer, V-shaped irons of the same specification, clean kerosene, oil basin, cotton yarn, etc.Esfarayan,　　A large amount of lubricating oil is stored.　　Many users, including new practitioners of slurry pumps, often fail to distinguish the difference between submerged vertical slurry pumps and submerged slurry pumps. The names of submerged and submerged slurry pumps seem similar, but there are essential differences. What is the difference between submersible slurry pump and vertical slurry pump?　　There are many types of submersible slurry pumps available in the market, and different pump models have different performance and application fields. Therefore, although the pump has a wide range of applications, if its model is not correctly and reasonably selected, its application effect will be great