Now you know the reason why the pump has air turbidity. In fact, this is a very common phenomenon. You don&#;t have to worry about it. Water pump can transport many things, such as water, oil,PiroerburHorizontal wear-resistant slurry pump, liquid metal, acid-base night and so on. It is a good means of transport.　　 When stopping the operation of the submersible slurry pump, and After that, cut off the power supply of the motor. If the temperature of the environment is low, open the square plug at the lower part of the pump body to remove the remaining water to avoid frost cracking. During operation, the maximum temperature of the bearing shall not exceed ℃ and the quantity of calcium base grease used for lubricating oil bearing shall be the same as that of the bearing bodyPiroerbur,　　Select an appropriate flow according to the water inflow of the well or pool or the water consumption required by the actual engineering system. During model selection, the flow shall be close to the model flow grade of the sample (to ensure that the pump operates in the high efficiency zone).　　Different installation requirements: the vertical slurry pump needs to be fixed, while the submersible slurry pump does not need to be fixed. It can directly invade into the liquid for operation.Jacobabad,　　The pump should be divided into two aspects: electricity and machinery. As for machinery, you can compare the previous maintenance records. The second is electricity. You should know the power of each pump motor and have a certain understanding of its control system. Slurry pump with mechanical seal　　When the water level reaches, the frequency of the frequency converter drops, and the slurry pump operates at a low speed. The higher the water level, the higher the speed. At the same time, the water level signal is transmitted to the control cabinet so that the operators can timely understand the liquid level. Through this control, the circulation in the slag slurry pool is basically unchanged　　There is a difference between submersible slurry pump and sewage pump. Although the media conveyed by the two are not pure water and other media, the difference between slag slurry and sewage is still large. Let&#;s take a look at the difference between the two.

　　 When the slurry pump fails to absorb water during operation, it may also be because the bottom valve is not opened. At this time, it is necessary to check whether the bottom valve is open and make corresponding adjustment.　　 for new or replaced deep well submersible pumps, after hours of use, check whether the seal is good. In the future, check it once a month. At the same time, check whether the shielding sleeve between the motor rotor and stator is well sealed. Try to reduce the number of starts in use.　　At present,PiroerburRubber lining submerged slurry pump, mechanical seals occupy an increasing share in the slurry pump seal market.Total quality assurance,　　The submersible slurry pump can be used to transport a lot of media containing solid particles when it is used at ordinary times, so it has an irreplaceable position when it is used. What is its own structure when it is used.　　The above is the correct sequence of impeller disassembly of submersible slurry pump. Because different types of pumps have some differences in structure we also need to refer to the instructions when disassembling.　　 Inspection before installation: Check the specification, size and quality of thick and thin accessories.

　　The two have certain commonalities. They are both submersible. As the name suggests, the pump is in an invasive state when running. The submersible slurry pump is a kind of submersible pump, but generally speaking, people often say that the submersible pump refers to the clean water pump, such as the submersible pump for domestic water and farmland irrigation and pumpingRecommendation and consultation　　It should be /-/ between. When the packing is worn, the packing gland can be properly pressed. If it is worn too much, it should be replaced. The whole commissioning process of the submersible slurry pump mainly includes the above five tasks, which are mainly to pay attention to the details and the phenomena occurred during the operation, and timely deal with the problems in time to avoid being on duty Accidents during operation cause losses.　　For example, the lubrication method, the number of impellers, the number of bolts and other small details determine that these slurry pumps are not used.　　It is an auxiliary means for some on-site monitoring.Piroerbur,　　 Next, the water seal, lock ring and other parts need to be installed.　　Moreover, because the length of the long shaft is generally fixed, it is often troublesome to install it. Therefore, the place where it operates will also be limited. If the equipment will　　If the pump outputs more medium liquid, it will certainly do more work. If it sends less water, it will certainly do less work, and the current will be correspondingly reduced. Pump power (kw) = head (m) × Flow (m/s) × The gravity of the fluid (kg/m for water) divided by (power conversion factor) divided by the efficiency of the pump (about