Organize, remove rust and repaint the structural components such as the suspension cage and guide rail frame for corrosion, and reinforce the severely corroded load-bearing membersCheck the interlocking equipment, up and down travel, and other safety maintenance switches of the cage door and fence doorCohen Nipps,The selection of vibration pickup points refers to the placement point of the sensor, which is used to measure the vibration amplitude of the workpiece. According to GB/T-, the acceleration sensor should be placed on the workpiece with a certain rigidity and a large amplitude, and its testing direction should be adjusted to be perpendicular to the plane where the effective zone of the vibration mode is located. Considering the complex structure of the lifting foundation workpiece and the uneven thickness of each component, the vibration pickup point is set in a thick area in the middle of the component.Check the oil level of the gearbox and make up for new oil if necessaryBosaso,Organize, and reinforce the severely corroded load-bearing membersAfter cleaning, clean the filter and replace it with a new filter element before adding new oil. What adverse reactions may occur during the early use of hydraulic cargo elevators?Monthly maintenance: View weekly inspection items

Quarterly maintenance: Check the items checked each monthDrivers should be responsible for supervising the uniform distribution of items transported by the platform on the platform as much as possible to prevent partial loading and prohibit overloading. Platform does not allowWeekly maintenance: According to the operation instructions,Cohen NippsMobile lifting platform, ensure that the elevator is inspected and smooth every daymanagement,Check the safety interlocking equipment of the first cut door of the hanging cageRegarding the construction elevator with counterweight, check the adjustment and fixation status of the counterweight guide wheel. Check the balancing equipment of the steel wire rope, the crown wheel, and the counterweight steel wire rope bracketEnsure that power cables and electrical circuits are not damaged

Please refer to the instruction manual for the maintenance and maintenance of the elevator to check the braking torque of the brakeproductionLeakage occurs due to looseness, vibration, and the influence of heat on the sealing surface and pipe joints of the machine; Some casting, processing and other defects are difficult to detect during assembly and debugging, but due to vibration and impact during the operation process, these defects are exposed manifested as oil (water) leakage. Therefore, leakage is prone to occur during the running-in period. Poor, due to the small fit clearance of newly assembled components and the difficulty in ensuring the uniformity of fit clearance due to assembly and other reasons, oil (grease) is not easy to form a uniform oil film on the friction surface to prevent wear. This reduces efficiency and causes early abnormal wear of the components. In severe cases, it can cause scratches or bite on the friction surface of precision fitting, leading to the occurrence of faults.Jinchuang lifting platform product feature is mainly used for high-altitude cargo transportation between floors. With a load capacity of - tons and a lifting height of - meters, a guide rail elevator, also known as a hydraulic elevator, can be installed indoors and outdoors. The lifting height is high and uses a side mounted oil cylinder, which runs smoothly, has low noise, is convenient for maintenance and has a long service life. In case of power outage, manual emergency descent can be used, which is safe, convenient, fast, and practical. The pit depth is generally cm-cm, and the top layer height is not affected, The pump station can be customized according to the on-site environment, suitable for - floors of steel structures or concrete factories. Both the internal and external parts can be used. The pump station adopts a joint venture pump station and an imported pump station from Italy. If the speed requirement is too high, a joint venture customized pump station can be used to meet the ideal delivery requirements. The oil cylinder and seals are made of imported components, solving the problem of unstable oil pressure for customers, The oil leakage problem of components . The oil cylinder is built into the platform . The heavy-duty steel wire rope wheel or weighted special chain ensures safety . The automatic insurance during the lifting process ensures vehicle safety . The synchronous device during the lifting process ensures that the vehicle may not overturn . The alarm setting before falling to the ground ensures the safety of the operator . The chain or steel wire rope fracture protection device . The hydraulic system pressure loss explosion-proof protection device . The elevator special flat permanent magnet switch is selected, The leveling effect is good. . The distance between heavy and empty loads is small, and the leveling accuracy is high. . Standard elevator boards, LCD display call boxes, relevant wiring harnesses, and connectors are selected. Beautiful appearance, easy operation, visual display of the position of the elevator car on the floor, wiring harness connected using connectors, with automatic and manual options.Many times, after installing hydraulic cargo elevators in factories, floors,Cohen NippsSelf walking aluminum alloy lifting platform, docks, and other places,Check the oil level of the gearbox and make up for new oil if necessaryThe wear rate is fast, and due to factors such as processing, assembly, and adjustment of new machine components, the friction surface is rough, the mating surface area is small, the concave and convex parts on the surface of the parts are intertwined and rubbed against each other. The metal debris that falls off from the grinding process, in turn, acts as abrasive and continues to participate in friction, further accelerating the wear of the mating surface of the parts. Therefore, during the running-in period, it is easy to cause wear on components (especially the mating surface), with a fast wear rate. At this point, if overloaded it may cause damage to the components and lead to early failures.All connecting shafts must have split pins and be sufficient.