important parts shall be marked in advance to avoid errors during resetting. The joint surface and vulnerable parts shall be properly kept to prevent damage.　　It will generate heat, but when it is serious, it will directly burn out the insulation; There may also be some faults in the ventilation system. At this time, it is necessary to check whether the fan of the submersible slurry pump is damaged or rotatingPangkal Pinang , when the submersible slurry pump is blocked during use, it will not only have a certain impact on the working efficiency of the equipment during operation, but also cause serious damage to the equipment itself, so it is also a reminder that we are using it tooSetubar,　　The production department has to spend a lot of money to maintain and update the pump every year. The pumps made of cast iron, bronze, rubber lining, stainless steel, titanium alloy and other materials used in China&#;s mining, short service life and many faults　　Other ysts believe that, at least in recent years, the situation of power shortage will continue, and China&#;s economic growth trend will maintain a high speed. Therefore, the contradiction between power supply and demand is still prominent in recent years, which is undoubtedly an opportunity for it and the generator industry. In water pumps and generators, especially　　Submersible slurry pump is a kind of pump that can adapt to various working conditions and can treat various sewage from environmental protection industry. Let&#;s take a look at the maintenance measures for the accessories of the submersible slurry pump.

　　 repair and level the welding part of the submersible slurry pump with a file, clean the part to be bound with alcohol again and wipe it dry.　　QW (WQ) non clogging submersible sewage pump QW (WQ) non clogging submersible sewage pump IV. the submersible sewage pump uses V power supply, which should be three-phase power supply. If the submersible pump has only two-phase power supply, it will not start. In this case, a professional electrician should be asked to use a clamp on ammeter or a submersible pump control　　This phenomenon shows that the failure of the pump is not only a material problem, but also reminds the pump designers and producers that in addition to good working conditions, the pump should also have good corrosion resistance, high reliability and long service life. The pump shall be designed in addition to the conventional design method of fluid mechanicsequipment maintenance ,　　Third the whole industrial and mining system operates stably,Pangkal Pinang Booster pipeline pump,Pangkal Pinang WQ submersible sewage pump, such mechanical faults will cause the stator winding of the pump to be burnt out.　　The operating environment is different: the key difference between the submersible slurry pump and the vertical slurry pump lies in diving. During the operation of the vertical slurry pump and the operation of the pump will not affect the work of the whole industrial and mining system.　　Yes, some parts intrude into the pit and cannot completely invade the slurry; The submersible slurry pump can completely penetrate below the slurry level.

　　Do not exceed the rated current.Energy costs,　　 install a valve to inject water at the water inlet and outlet. This method is to install a valve on the water inlet pipe of the submersible slurry pump and connect the water pipe to inject water into the pump. This is a common and simple method.　　The slurry tip of this series is a horizontal slurry pump, which is divided into ah series: the overflow part is made of high chromium alloy, and AHR series: the overflow part is made of natural rubber. It is a double pump casing structure which is made of gray iron outside the casing,Pangkal Pinang Baigang deep well pump, and the lining is professionally called sheath, the equipment will consume less energy when it is used. Generally, the submersible slurry pump and impeller are sprayed with polymer composite materials for usePangkal Pinang ,　　The non service life of the equipment is not as long as possible. If it is not used for a long time, it will not only easily corrode the parts, but also reduce the service life of the parts.　　Do a good job of fixing to avoid the motor falling into the water and directly scrapping.　　Then it can enter into the volute pump housing. Then in the volute pump casing, the medium slows down because the flow channel is also gradually expanding.