Stainless steel grade group Series & mdash; Chromium nickel manganese austenitic stainless steel series & mdash; Chromium nickel austenitic stainless steel model & mdash; Good ductility, used for molding products. It can also be machined to harden rapidly. Good weldability. The wear resistance and fatigue strength are better than those of stainless steel.The surface resistance is less than mb; Wear protection; Scalable; Excellent chemical resistance; Good alkali metal and acid resistance; Strong toughness; Flame retardant.Netherlands, carefully observe whether the surface of the pipe is shiny, damaged and crushed, and pay attention to whether the incision is neat. If these phenomena occur, they should be carefully considered.After fine tuning the molten steel temperature in the argon blowing station, it is lifted to the ladle rotary table for continuous casting.Sullivan,Welding, high frequency preheating plus three torch argon arc welding, high frequency preheating plus plasma argon arc welding. The progress of combined welding is very significant. As for the combined welding of steel pipe with high-frequency preheating, the weld quality is equivalent to the conventional argon arc welding and plasma welding, the welding operation is complex, and the whole welding is easy to complete automation. This combination is easy to connect with the existing high-frequency welding equipment, with low investment cost and good benefit.Application field: launch the market plan of stainless steel pipe in the target market of new products, such as stainless steel kitchen equipment.The main control load of the platform has high requirements for the shear bearing capacity of the guide leg of the offshore platform. In order to study the factors affecting the shear capacity of the jacket legs of the stainless steel pipe in pipe concrete-filled steel tubular offshore platform, a total of concrete-filled steel tubular shear members were fabricated to study the effects of outer steel pipe material, concrete strength, void ratio and shear span ratio on the shear capacity of concrete-filled steel tubular in pipe. It is found that the shear strength of members increases with the decrease of void ratio and the increase of concrete strength; The larger the shear span ratio, the empirical formula of shear capacity of concrete-filled steel tubular in pipe is proposed, which is analyzed and verified by ABAQUS finite element modeling software. The results show that the simulation is in good agreement with the test results. In order to study the axial compression performance of stainless steel tube concrete conduit leg and the axial compression performance of stainless steel concrete conduit leg, experiments are used to verify the correctness of the finite element model. The load displacement curves of specimens in groups were compared, and the effects of different void ratio, concrete strength, diameter thickness ratio and bone index on the axial compression performance of concrete-filled stainless steel tubular short columns under axial compression were analyzed. The results show that with the increase of concrete strength, the bearing capacity of specimens increases, but the ductility of specimens decreases; With the increase of void ratio and diameter thickness ratio, the bearing capacity of the specimen decreases; The bearing capacity of stainless steel tube concrete can be effectively improved by adding steel bone; Increasing the bone matching index of steel bone can improve the bearing capacity of the specimen. Based on the jacket offshore platform, it is proposed to replace the four hollow steel conduit legs of the original offshore platform with concrete-filled steel tube in stainless steel tube to form a new composite offshore platform with concrete-filled steel tube in stainless steel tube, so as to improve the ice resistance and disaster prevention ability of the offshore platform. The scale test on the offshore platform shows that the composite offshore platform of concrete filled steel tubular in stainless steel pipe (hereinafter referred to as the composite offshore platform) has better anti icing performance than the ordinary jacket offshore platform. Taking push as an example, the peak acceleration and displacement of the upper deck of the composite offshore platform of concrete filled steel tubular in stainless steel pipe are reduced by % and % respectively. The analysis of ABAQUS finite element and experimental simulation results shows that the error of the two results can be basically within %. Through the simulation analysis of the ultimate bearing capacity of the stainless steel tube in tube concrete-filled steel tubular composite platform and the original offshore platform, it can be seen that the stainless steel tube in tube concrete-filled steel tubular composite platform has stronger ultimate bearing capacity. Therefore, the composite offshore platform of concrete-filled steel tube in stainless steel tube is a good new type of jacket offshore platform. Axial compression tests were carried out on austenitic and duplex stainless steel tube concrete short columns. The ultimate load, longitudinal strain and circumferential strain of the short columns under axial compression were measured. The effects of steel tube wall thickness and concrete strength on the bearing performance of the short columns were investigated. Reference was made to the European Code for design of concrete filled steel tubes (Eurocode), China's relevant regulations D --dlt- and CECS calculate the preparation of stainless steel pipe construction, prepare construction scheme and construction schedule scheme, and establish quality standards.

During welding, the process of ventilation in advance and gas stop behind shall be adopted, and the adhesive cloth on the outside shall be torn off while welding. Because the blocking plate is composed of rubber and white iron sheet, it is not easy to be damaged, so this welding can well ensure that the inner side of the weld is filled with argon and its purity, so as to effectively ensure that the metal on the inner side of the weld is not oxidized and ensure the quality of weld backing welding.Delivery status: to be delivered after heat treatment and leveling.Proper heat treatment process can prevent intergranular corrosion and obtain excellent corrosion resistance.how,Welding, high frequency preheating plus three torch argon arc welding, high frequency preheating plus plasma argon arc welding. The progress of combined welding is very significant. As for the combined welding of steel pipe with high-frequency preheating the weld quality is equivalent to the conventional argon arc welding and plasma welding, the welding operation is complex, and the whole welding is easy to complete automation. This combination is easy to connect with the existing high-frequency welding equipment, with low investment cost and good benefit.Shape, stress, temperature and metal flow of forgings and dies. Results the multi-step upsetting extrusion process under high temperature can make the end of steel pipe meet the forming requirements. Conclusion the plastic forming process of steel pipe end is feasible, which has important reference significance for the improvement of pipe connection mode of railway freight car braking system.Model & mdash; Martensite (high strength chromium steel) good wear resistance and poor corrosion resistance.

Solution treatment. The main purpose of water quenching after heating the steel to ~ ℃ is to dissolve the carbide in austenite and keep this state to room temperature, so that the corrosion resistance of the steel will be greatly improved. As mentioned above, solid solution treatment is usually used to dissolve CrC in austenite and then cool rapidly. Air cooling can be adopted for parts, and water cooling is generally adopted.Click to view,NetherlandsArgon arc welding of thin stainless steel pipe,Restate the quality of stainless steel pipe, such as stainless steel pipe, we promise & ldquo; chromium and nickel & rdquo; Penalty for false and provide quality inspection report and certificate of conformity.Corrosion resistance most stainless steel products require good corrosion resistance. Stainless steel pipe is similar to class I and II tableware kitchen, water heater, water dispenser, etc. Some foreign businessmen also test the corrosion resistance of products: use NaCl aqueous solution to warm to boiling. After a period of time, the solution is to drain, wash and dry and determine the weight loss to determine the degree of corrosion.Section shape stainless steel pipe can be divided into round pipe and special-shaped pipe according to the section shape. Special shaped tubes include rectangular tubes, rhombic tubes, elliptical tubes, hexagonal tubes, octagonal tubes and various cross-section asymmetric tubes. Special shaped pipe is widely used in various structural parts tools and mechanical parts. Compared with circular pipe, special-shaped pipe generally has large moment of inertia and section modulus, and has large bending and torsion resistance, which can greatly reduce the structural weight and save steel.Netherlands,The best way to improve the quality of stainless steel pipe fittings is to change the process from ingot to billet. Due to the improvement of continuous casting process, this has become a necessary means to improve product quality.The scale pretreatment of stainless steel pipe makes the scale loose, and then acid pickling is carried out for easy removal. The pretreatment can be divided into the following: alkaline salt melting treatment method. The alkaline melt contains % hydroxide and % salt. The proportion of the two in the molten salt shall be strict, so that the molten salt has strong oxidizing power, and the content shall not be less than % (wt) It is treated in a salt bath furnace at ~ ℃ for minutes for ferritic stainless steel and minutes for austenitic stainless steel. Similarly, iron oxides and spinels can also be oxidized by salt to become loose ferric oxide, some of the formed oxides peel off and sink to the furnace bottom in the form of sediment. Alkaline salt melting pretreatment Process flow: steam degreasing → preheating ( ~ ℃,NetherlandsStainless steel filter pipe, time ~ min) ↠ molten salt treatment & rarr; water quenching & rarr; hot water washing. Molten salt treatment is not suitable for assemblies with weld gap or crimping. When the parts are taken out of the molten salt furnace, a stream of alkali and salt mist will be splashed during water quenching, so deep well anti splash water quenching tank shall be used during water quenching. During water quenching, firstly lift the parts basket into the tank, stop above the horizontal plane, close the tank cover, and then lower the parts basket into the water, Professional L stainless steel pipe, s stainless steel pipe and L stainless steel pipe are stable, safe, reliable and maintenance free. The technical level has reached the domestic level and the international advanced level of similar products until submerged.All steel with openings at both ends and hollow sections,NetherlandsStainless steel pipe 316, and with a large ratio of length to section perimeter, can be called steel pipe. When the ratio of length to section perimeter is small, it can be called pipe section or tubular fittings, which belong to the category of pipe products.