Extrusion method: This production method is to cast copper ingots after smelting, and extrude copper tubes by large extruder after secondary heating.On the other hand,Olu304 stainless steel plate, in the steel plant, the lock price of the steel plant has been falling all the time, and the order receiving is poor. The capacity utilization rate of the steel plant is low, but the market is still in oversupply. The stock of the steel plant and the spot stock are both risirising, so the market price has fallen sharply. Subsequently, the futures market rebounded in a wave, and the spot price also increased with the increase. There was an instant of large volume of transactions. However, with the decline of black futures, the market transaction volume shrank significantly. In addition, the inventory pressure was high, traders shipped at low prices, and the spot price fell under pressure. Due to the strong drop resistance of medium and thick plates, the drop amplitude and rate are less than those of threads.Olu,Methods of copper pipe anti-corrosion Strengthen scientific research.Hygiene and health: various modifiers, additives,Remove the flame. If the filler metal does not melt, continue to heat the joint and try again. The melted filler metal is sucked into the casing port according to the capillary effect until a complete filler metal ring appears on the casing port. Remove the flame Pay special attention not to let the flame directly contact the filler metal. It should be the heat at the joint that melts the filler metal. In order to clean the copper pipe, the welding flux must have a degree of corrosivity, and shall be cleaned after brazing. The so-called & quot; self-cleaning& quot; fluxes are generally not recommended because of their corrosivity.If you want to make the copper surface become bright again, but also quickly remove the rust and oxide layer on the copper surface to restore the luster of the copper itself.The conductive production of copper tube is the latest method for this method. It is the production of nanocrystalline copper materials with conductivity. Because this raw material is very special, it is a copper material produced by using nanotechnology, and copper ions can be separated by conductivity, so that copper tubes can be produced with the separated copper ions. This method is very complex requires high technology and new equipment, so only advanced foreign countries can use this production method.

In the first ten days of May, the overall order receiving quantity of Tianjin Hebei Henan Plate Plant was not ideal. According to the monitoring data the overall order intake of medium and heavy plate mills in Tianjin Hebei Henan region in the first ten days of May remained stable and weak. Due to the weak market shock, the total quantity of post settlement agreements of main steel plants can exceed tons.Under the action of high welding temperature while at the end of April, the evaporation amount of zinc is as high as % during shielded metal arc welding. A large amount of zinc evaporation leads to the decline of mechanical properties and corrosion resistance of welded joints and also increases the sensitivity to stress corrosion.The blowing mouth of the welding tool should not be too small to avoid excessive concentration of heat.equipment maintenance ,The production method of soft copper tube is basically the same as that of hard copper tube, that is, the annealing process is added compared with the hard copper tube. Annealing of copper tubes means that they are calcined in a high temperature furnace to change the arrangement of the elements in the copper tubes. However,Olucopper Stick, after annealing, the copper tubes will become soft, which makes it easier to bend. The copper tubes produced in this way are called soft copper tubes.Red copper inventory in key areas has risen continuously, but the total pressure is not big. From the current overall inventory situation of the main distribution centers Wu an, Jiangyin and Lecong, the inventory level remains relatively moderate, and the pressure on the market is relatively small. In Wu an market, according to the data, as of May , the total inventory of medium and thick plates in Wu an was close to tons, increasing by tons on a weekly basis. In late April, it reached tons lower in the year, down tons from the high level after the Spring Festival, and rose for three consecutive weeks. In terms of the ovquantity, it should be said to maintain a relatively moderate level.Let s elaborate on the advantages of copper pipe materials: copper pipe floor heating refers to a heating method that uses hot water as the thermal medium, circulates in the copper pipe heating pipe, heats the floor, and heats the floor through the ground in the form of radiation and convection heat transfer. I. The copper tube has fast heat dissipation effect and strong heat resistance. Even under the condition of high temperature water supply, the service life of the floor heating tube will not be affected. Two. Copper pipe is a metal pipe,o it is not easy to scratch. Therefore, it is not easy to leak. Three. High temperature resistance, high pressure resistance, relative to any ordinary plastic pipe. Copper tube floor is warm and resistant to high temperature and pressure. Four. Long service life. Five.

Advantages and scope of application of copper tube ground heating At present, ground heating is not only a comfortable heating method, but also a symbol of modern life quality. More and more houses, public buildings, sports facilities industrial facilities and other places begin to use ground heating radiator, which is an important part of ground heating. Due to the corrosion resistance of copper, copper tubes are selected as the main material of radiator in many places.install,Advantages of red copper tube Durability: copper has stable chemical properties, integrating cold resistance,Olu5052 aluminum bar, heat resistance, pressure resistance, corrosion resistance and fire resistance, and can be used in different environments for a long time.As the inner wall of the pipe rubs with water, its film is damaged, resulting in erosion corrosion. The higher the water pressure, the greater the flow, and the more serious the corrosion.When stacking, it shall be stacked reasonably and placed first.Olu,On November , the market price of Cangzhou copper bar was stable. According to the monitoring data of Lange Iron and Steel s cloud business platform, the market price of * mm cold drawn steel produced in Linyi is yuan, the market price of * mm in Linyi is yuan, the market price of * mm in Jianlong is yuan, the market price of * mm in Yuanhua is yuan, the market price of * mm in Juneng is yuan, the market price of * mm in Baotou Steel is yuan, and the market price of * mm in Juneng thermal expansion is yuan.Although the opening continued the weak trend, the intraday transactions improved, and the prices of some copper bar manufacturers rose. From the specific situation, although the manufacturer feedback that the shipment is average, the mentality is relatively calm, the market inventory is not much, and the manufacturer is not willing to significantly reduce the price. In terms of the market, and the downstream mainly focuses on callback buying without panic inventory clearing. It can be seen that although the steel market continues to shake, the overall demand for strip steel remains in a good state.On October , according to the Economic and Information Commission oong Province, Shandong Province had resolved the overcapacity of million tons of pig iron and million tons of crude steel, and all the de capacity equipment had been shut down and withdrawn. On October