Impeller protection in order to ensure the operation of the submersible slurry pump, it is necessary to timely adjust the clearance between the impeller and the front guard plate. When adjusting the impeller clearance, first stop the pump,Basrat KadimaPipeline pump, loosen the bolts pressing the bearing box, loosen the adjusting nuts, make the bearing components move forward, and roll the shaft by hand to press the　　 strip the outer layer of the cable to expose the copper wire for to mm, gradually thin the rubber near the wire core grind it to the oxide layer on the wire core, wipe the wire core with alcohol (or hydrochloric acid), wrap the insulation layer and sheath layer,Basrat KadimaDeep well pump, and dry it naturally.Basrat Kadima,　　 whether gate valve, bottom valve, vent valve,Basrat KadimaWQ submersible pump parameters, pressure gauge, etc. are required　　With the arrival of midsummer and the intensification of the contradiction between supply and demand of kerosene, the power supply across the country has been tense again, which has driven the hot sale of it and generators in the phase II market. According to relevant data, there is still a large gap after China&#;s power balance.Hualien,　　 If the power cord is not well contacted, it will also lead to the burning of the motor.　　 Why does the demand for submersible slurry pumps increase greatly? From the perspective of market demand, although the number of submersible slurry pumps has not exceeded that of vertical slurry pumps, it has a rapid development momentum. The main reason is that the above-mentioned use is convenient and flexible; In addition, the application market of submersible slurry pump is also better than that of vertical pump　　It is an auxiliary means of on-site monitoring. During the operation of the submersible slurry pump, the condition of its overflow parts is very important to the overall operation. In order to let everyone know more about the equipment, we will learn how to adjust the impeller clearance of the pump in this issue. I hope it will help you.

　　It can also be used for cooling and lubrication. Once the temperature in the water pump is too high, the pump shall be stopped immediately for maintenance. Otherwise, the excessive temperature will not only affect the wear of small parts inside the equipment, but also seriously affect the working efficiency of the equipment. So what is the reason for the high temperature of the equipment　　Test the steering first, and then connect the motor to the ash pump. There is a removal ring at the journal. This device can prevent the impeller from reversing.　　The water slurry pump is a widely used equipment. Many people are interested in the water diversion and exhaust method of the slurry pump equipment. Now let&#;s talk about the water diversion and exhaust method of the submersible slurry pump: the submersible slurry pump needs to pump out the water to form a vacuum, and then supply water,Price,　　Stability and reliability of seals between pump bodies.　　Circumference. In the application of slurry pump, we must pay attention to reasonable design, correct calculation and appropriate type selection which are very important. In addition to the main wheel, a set of stirring impeller is added at the bottom of the product, which can spray the precipitated slag into a mixture of water and solid particles　　After that, before starting again, check whether the impeller rolling is normal and whether the bearing assembly compression bolts are tightened, and then start the pump.

　　 In addition, the noise method directly detects the noise of the equipment in the detection process, but this measurement will also be affected by the surrounding noise, so in fact, this measurement is not very accurate.Where is good,　　When in use, it can drive the impeller to rotate so as to drive it to flow.　　 Check the wiring of the motor itself: it may be the high temperature caused by wrong wiring. If the wiring is wrong, quickly connect it back to the correct method.　　Reasonable.Basrat Kadima,　　The above four methods can be used to detect whether the submersible slurry pump has cavitation, because if the equipment is in use it will have a great impact on the operating efficiency. Even if the cavitation time is long, it will also have a certain impact on other parts of the equipment. Sometimes submersible slurry pump　　The impeller of the submersible slurry pump may need to be disassembled for maintenance or repair during use. However, we may make mistakes during disassembly. Let&#;s take a look at the correct disassembly of the impeller　　 If the power cord is not well contacted, it will also lead to the burning of the motor.