Measures to improve the welding quality of stainless steel pipe in order to ensure that the outer surface of stainless steel pipe is not damaged and purified, the maintenance of stainless steel pipe should be strengthened in each process of consumption, mainly including the following three aspects: the processing and consumption of stainless steel pipe should have a special consumption workshop (wood board is well used) , avoid the machining platform of austenitic stainless steel and carbon steel or solid overhead.Some reasons for product composition ratio: in order to reduce the production cost, reduce the proportion content of some important elements such as chromium and nickel, and increase the content of other elements such as carbon. This production phenomenon that the composition ratio is not strictly in accordance with the product model and product characteristics not only greatly reduces the product quality, for example, when the chromium content of stainless steel pipe is insufficient, it not only affects the production The corrosion resistance and formability of products have potential product quality and safety hazards when they are used in chemical, equipment and production industries. At the same time, they also affect the appearance and oxidation resistance of products.Sainte-Anne, Density & rdquo; Density of series: s, S and density stainless steel coils of are divided into Austenitic, ferrite, martensite, duplex (ferrite austenite) stainless steel cold rolled coil and stainless steel hot rolled coil.The intergranular corrosion of austenitic stainless steel can be prevented by adding Ti, Nb and other elements that can form stable carbides (tic or NBC) and avoiding the precipitation of crc on the grain boundary.Chililabombwe,Sainte-AnneStainless steel explosion-proof flexible connecting pipe,Austenitic stainless steel has good resistance to uniform corrosion, but there are still the following problems in local corrosion resistance: intergranular corrosion of austenitic stainless steel. Austenitic stainless steel will have intergranular corrosion when it is kept warm at ~ ℃ or cooled slowly. The higher the carbon content, the greater the tendency of intergranular corrosion. In addition, which is caused by corrosion of the primary cell. This intergranular corrosion phenomenon also exists in the ferritic stainless steel mentioned above.Austenitic stainless steel is generally used for manufacturing and manufacturing chemical equipment components, low-temperature equipment components in refrigeration industry, and can be used as stainless steel spring and clock spring after deformation strengthening.The protection mechanism of stainless steel backing wire + TIG process is that the back weld is protected by the metallurgical reaction of slag produced by welding wire melting and its alloy elements, and the front weld is protected by argon, slag and alloy elements.

Stainless steel pipe factory stainless steel products are widely used in hardware products, furniture, mechanical structure, precision medical instruments, fluid transmission pipelines, machinery, medical oil, natural gas, water, gas, steam and other industries.Low temperature embrittlement --- in low temperature environment, the deformation energy is small. In the low temperature environment, the phenomenon that the elongation and area shrinkage decrease is called low temperature embrittlement. Most of them are produced on the body centered cubic structure of ferrite series.Accounting for about % - % of the total steel, it is widely used in the national economy. Because the steel pipe has a hollow section, it is suitable for gas and solid transmission pipelines; at the same time, compared with the round steel of the same weight, the steel pipe has large section coefficient and high flexural and torsional strength, so it has also become an important material in various machinery and building structures. Stainless steel is used Under the condition of equal weight, the structure and components formed by pipe have a larger section modulus than solid parts. Therefore, stainless steel pipe itself is an economic section steel that saves metal. It is an important part of steel, especially in oil drilling, production and metallurgyLatest quotation,The shape of pipe end stainless steel pipe can be divided into smooth pipe and threaded pipe (threaded steel pipe) according to the state of pipe end. Threading pipe can also be divided into ordinary threading pipe (pipe for conveying low pressure such as water and gas, which is connected by ordinary cylindrical or conical pipe thread) and special threaded pipe (pipe for petroleum and geological drilling, which is connected by special thread for important threading pipe). For some special pipes, in order to make up for the impact of thread on the strength of pipe end, the pipe end is usually thickened before threading (inner thickening, outer thickening or inner and outer thickening).Stainless steel has two classifications: one is divided into chromium stainless steel and chromium nickel stainless steel according to the characteristics of alloy elements; The other is divided into m stainless steel, f stainless steel, a stainless steel and A-F duplex stainless steel according to the microstructure of steel in normalized state.Chloride ions exist in the service environment. Chloride ions exist widely such as salt, sweat, sea water sea breeze, soil, floating rust of iron foam and so on. Stainless steel corrodes rapidly in the presence of chloride ions even more than ordinary low carbon steel. Therefore, there are requirements for the service environment of stainless steel, and it is necessary to remove dust frequently and keep it clean and dry. (in this way, we can give him a & ldquo; improper use & rdquo;) there is an example in the United States: an enterprise uses an oak container to contain a solution containing chloride ions. The container has been used for nearly years. The ninetieth generation of the last century plans to replace it. Because the oak material is not modern enough the container leaks due to corrosion days after it is replaced with stainless steel.

Brinell hardness in stainless steel pipe standards, Brinell hardness is widely used, and the hardness of the material is often expressed by indentation diameter, which is intuitive and convenient. However, it is not suitable for steel pipes with hard or thin steel.market,When using this process, the following key points should be paid attention to: during the welding process, the correct included angle between the welding handle,Sainte-AnnePrice of stainless steel strip, welding wire and weldment should be maintained. The ideal caster angle of the welding handle nozzle is & deg; & mdash; & deg;, and the included angle between the welding wire and the weldment surface is & deg; & mdash; & deg;; correct the molten pool temperature, change the included angle between the welding handle and weldment, change the welding speed, so as to ensure Beautiful weld formation (uniform width, no concave, convex and other defects) During operation, the current shall be slightly larger than that of solid core welding wire, and the welding handle shall be slightly adjusted to accelerate the separation of molten iron and molten flux coating, so as to facilitate the observation of molten pool and penetration; when filling the welding wire it shall be sent to places of molten pool and pressed inward slightly to ensure penetration and prevent concave; during welding, the welding wire shall be regularly sent and taken out, and the welding wire shall always be ensured Under the protection of argon to prevent the end of the welding wire from being oxidized and affect the welding quality; pay attention to the welding quality of the arc and arc stop,Sainte-AnneStainless steel rusty, and the spot weld shall be polished to & deg; the slope shall be gentle, and pay attention to the defects such as arc pit and shrinkage hole during arc stop.With the development of social economy, the application of stainless steel pipe has been more and more popular. It will bring new changes in various fields.AUSTENITIC FERRITIC duplex stainless steel. It has the advantages of both austenitic and ferritic stainless steel, and has superplasticity. Martensitic stainless steel. High strength,Stainless steel pipe is safe, reliable, hygienic, environmentally friendly, economical and applicable. The successful development of pipeline and new reliable, simple and convenient connection makes it have more irreplaceable advantages of other pipes. It will be used more and more in engineering, and the use will be more and more popular. It has a good prospect.Austenitic stainless steel austenitic stainless steel is developed to overcome the lack of corrosion resistance and brittleness of martensitic stainless steel. The basic composition is crl% and Ni%, which is referred to as - steel for short. Its characteristic is that the carbon content is less than .%, and the single-phase austenite structure is obtained by the combination of Cr and Ni.After that, the second widely used steel is mainly used in food industry, pharmaceutical industry and surgical equipment. Adding molybdenum makes it obtain a special corrosion-resistant structure. Because it has better chloride corrosion resistance than stainless steel pipe