The manufacturer of the hydraulic cargo elevator tells you the reason and cleaning method: Reason: Overload cleaning method: Reduce the load to clean. Reason: The return valve is not closed. Cleaning method: Tighten the return valve to clean. Reason: The one-way valve of the manual pump is stuck and the return valve is malfunctioning. Cleaning method: Unscrew the bolt at the valve port of the oil pump, conduct maintenance, and replace the cleaning hydraulic oil to clean.The hydraulic lifting platform often checks the connection status of each part, and if there is any looseness it should be tightened. The connection bolts of the machine body should be checked for tightness when the elevator body is under pressure (the compression condition can be formed by rotating the arm). All connecting shafts need to have split pins and need to be fully opened.Tilburg,The hydraulic system of the fixed lifting platform of the hydraulic cargo elevator is equipped with anti fall and overload safety protection devices, and operation buttons can be set on each floor and the lifting platform workbench to achieve multi-point operation.Therefore, it is necessary to avoid dead bends as much as possible and check the tightness of the sleeve in a timely manner.Herzliya,Surface paint quality: The paint should be smooth and flat, have good adhesion with metal, have uniform color, no bubbles, no cracks, and there should be no wrinkles, pits, paint leakage and sagging.When the hydraulic lifting platform is working, the larger the mass of the object the load cannot exceed its rated load. When it is raised to a certain height, the greater the shakingHydraulic lift cargo elevators belong to high-altitude work equipment. Small shaking of the scissor type structure is normal, but excessive deviation is a symptom. It is necessary to find the cause and make correct judgments in a timely manner. Generally speaking, operations above meters are generally allowed. Due to its own weight, devices above this height begin to vibrate in different ranges. The vibration range depends on factors such as weight, lifting height, and intensity of high-altitude operations.

Voltage too low: Measure the starter voltage,TilburgHydraulic guide rail lifting platform, with an allowable fluctuation range of± %.The hydraulic elevator has no counterweight device, which improves the utilization rate of the well surface.Separate: Loading and unloading on different platforms.Quality inspection report, the location of the platform should be selected to minimize the distance of the handling tools and vehicles in the factory. It is much easier to move a fully loaded transport vehicle to a designated location outside the building than to transport the loaded materials one by one to the designated location indoors. When selecting a platform location, full consideration should be given to the production process and operational needs of the factory. There are two modes of platform layout: merging: loading and unloading on the same platform.After hours of elevator operation, perform minor repairs to the mechanical and electrical systems.For hydraulic cylinders in hydraulic elevators, it is not practical to change their effective working area A (equivalent to displacement) to adjust the speed. Generally, the speed can only be adjusted by changing the flow rate. For variable displacement motors, speed regulation can change both the flow rate and the motor displacement.

Protective device: In case of power or oil circuit failure, there should be a safety rope to prevent the workbench from falling out of control. (Allow controlled descent)retailer,Reason: Cleaning method for internal leakage in the oil cylinder: Replace the sealing element of the oil cylinder. The lifting platform does not lower. Reason: The lowering valve is malfunctioning. Cleaning method: When pressing the lowering button, check whether the lowering valve is powered on. If there is no electricity, clean it as much as possible; If there is power, clear the malfunction of the lowering valve itself or replace the lowering valve. The sliding valve should be kept clean and.The overflow valve cannot be debugged on its own. The reason why hydraulic cargo elevators are slow is mainly due to human factors in the later stage. Therefore, attention should be paid to maintenance and upkeep during use to reduce accidentsBefore installation,TilburgTwo ton hydraulic lifting platform, the installation personnel should confirm the infrastructure such as the foundation and shaft, pay attention to alignment,TilburgHydraulic lifting platform, leveling, and alignment points, and confirm that the foundation meets the requirements before construction.Tilburg,Stability: The workbench should evenly withstand % of the MAX load capacity and be stable at the MAX elevation.Separate: Loading and unloading on different platforms.When the hydraulic system malfunctions, the hydraulic elevator may experience problems with the hydraulic pump, motor, valve, and hydraulic installation after repairing the hydraulic system, which can easily cause vibration and generate significant noise.