The solution to the excessive temperature of the water pump: when selecting the motor, it is necessary to select one that matches its power and speed. In addition, the cooling fan should be installed on the main shaft. It is also possible to appropriately increase the number of fan blades, but pay attention to adjusting the vacuum pump　　It is not correct that it has no effect on us.Salmas,　　 before starting, check all circuits and switches to see if their wiring is correct and reliable, then turn them over the ground for ~ minutes (the time should not be too long to avoid damaging parts or burning motor windings), and check whether the motor running direction is correct. If the above problems are not found it can be started　　The seal cannot bear the water pressure at this depth. Once the water leaks, the motor will not work normally, resulting in damage to the submersible slurry pump. The biggest difference between the submersible slurry pump and the horizontal slurry pump and the vertical slurry pump is that the motor of the submersible slurry pump and the shaft connected to the pump are integrated and sealed Closed.Makassar,　　When this type of pump is used at ordinary times, the pump and motor operate in a coaxial whole. When it runs, the motor shaft will drive the impeller of the pump to rotate, and then at this time, the rotating force can be brought to the medium, so that　　 If the head of the submersible slurry pump is too low or the head is higher than the practical condition, the flow will be large and the current will rise. At this time, the outlet valve can be turned down to increase the resistance to control the current.　　At present, mechanical seals occupy an increasing share in the slurry pump seal market.

　　In addition to the main impeller inside the equipment, a set of impeller for mixing will be added at the bottom of the equipment, so that some mortar slowly settled inside the equipment can be mixed with water to become a flowing medium, so that the equipment can be used without its　　 the resistance shall be greater than megohm after filling with water. Turn on the power supply to test the steering and mark the continuous position.　　Fourth, model selection parameters: outlet diameter, flow, dust, motor power, impeller speed, maximum particle and weight.Quality department,　　Water or air leakage in the pipeline. The nut may not be tightened during installation. If the leakage is not serious the air or water leakage can be treated with cement or cement slurry mixed with asphalt oil. Temporary repairs can be done with some wet mud or soft soap. If water leaks at the water pump joint, tighten the nut with a wrench. as　　 strip the outer layer of the cable to expose the copper wire for to mm, gradually thin the rubber near the wire core, wipe the wire core with alcohol (or hydrochloric acid),SalmasSplit vertical pipeline pump, wrap the insulation layer and sheath layer, and dry it naturally.　　The structure of the submersible slurry pump will be more intuitive. First, and then leave the edge of the impeller at a higher speed

　　For example, concentrate and tailings are treated in the concentrator, ash and slag are removed from the power plant, slime and dense medium coal are transported in the coal preparation plant, and slurry is transported in coastal river mining operations. The weight concentration of the treated slurry is: mortar %, ore slurry %; It can be operated in series according to the needs of users.OK or not?,　　It can also be used for cooling and lubrication. Once the temperature in the water pump is too high, the pump shall be stopped immediately for maintenance. Otherwise,SalmasQuotation slurry pump,SalmasSelf priming slurry pump wholesale, the excessive temperature will not only affect the wear of small parts inside the equipment, but also seriously affect the working efficiency of the equipment. So what is the reason for the high temperature of the equipment　　 pump room height and allowable lifting height of lifting equipment　　The motor is scrapped. Moreover, because the length of the long shaft is generally fixed, the installation and use of the pump is troublesome, and the application occasions are subject to many restrictions.Salmas,　　What is the solution to this situation?　　Start the priming pump. Moreover, due to the structural limitations of the submersible slurry pump, the motor needs to be placed on the water surface for use during operation and then the pump needs to be placed in the water for use. Therefore, the submersible slurry pump must be　　Commodity.