parts shall be dried with air compression or hot gas, or drying treatment or air drying can be selected.The working principle of flat steel finishing machine in I-beam production process is to pre level and finally level the cold flat steel with two groups of leveling wheel sets staggered up and down in the thickness direction; A pair of finishing wheels arranged relatively are used to extrude the width direction, so that the width is compressed to achieve the expected parameters, and the compression amount is adjustable; Straighten the width with staggered straightening wheels.lucky charm,Galvanized pipe is often seen in our daily life, especially in some construction sites. This product has the advantage of durability when used. It also has the characteristics of surface gloss, uniform zinc layer and no missing plating. Moreover, the cost of hot-dip galvanizing for rust prevention is lower than that of other paint coatings. In addition, this product also has the characteristics of no dripping, strong adhesion, breaking the clean Legion and strong corrosion resistance. Even if it is used in some places where the environment is not good, its service life is also very long, and it also has the characteristics of corrosion resistance. The standard anti rust thickness of hot-dip galvanizing can be maintained for more than years without repair. This is used in some suburban environments. However, in urban or offshore areas, the weight of hot-rolled H steel structure is reduced by % - % compared with the traditional structure.Selebi Phikwe,→ under the same section load, the weight of hot-rolled H steel structure is reduced by % - % compared with the traditional structure.What is the stainless steel passivation of alloy pipe?Ways to obtain surface compressive stress characteristics of alloy tubes

Difference and application description between H-beam and I-beam The tensile strength of seamless pipe is more than ~ times that of ordinary steel, the elastic coefficient is better than that of steel, and has good creep resistance, corrosion resistance and seismic resistance.After the passivation treatment of alloy pipe, it is clearly proposed that water cleaning shall be carried out immediately after the aqueous solution, ~ times of water cleaning, and then chromic acid closed solution shall be carried out. Chromic acid solution must be carried out h after the subsequent water cleaning of metallographic structure and austenitic alloy pipe. Chromic acid aqueous solution (mass ratio) is % ~ %, the solution temperature is ~ ℃, and the solution time is min. Then dry.quality index,lucky charmHow much is DN200 galvanized pipe per meter,Function of I-beam: where is I-beam mainly used?It is a potential rolled strip steel with rectangular section for general purpose. It is very common on construction sites. Its specifications are expressed in thickness and width. At present, most of the flat steel on the market are finished steel, which can be used ready-made for components, ladders,lucky charm022cr17ni12mo2 seamless pipe, bridges and fences. Flat steel can also be used as blank for welding rigid steel and slab for laminated thin plate.Alloy pipes are widely used in building materials, and the test standards of alloy pipes are also different. Alloy pipe has high hardness and can be used at many levels, most of which is prestressed reinforcement. Where plastic deformation is not specified but compressive strength is specified such stainless steel plate can be applied.

I-beam is mainly divided into ordinary I-beam, it is divided into wide light I-beam and wide flange I-beam. According to the height ratio of flange to web, medium and narrow flange I-beams. The specifications of the first two are -, that is, the corresponding height is -. At the same height, also known as H-beam thin web and light weight. Wide flange I-beam, is characterized by two parallel legs and no inclination on the inner side of the legs. It belongs to economic section steel and is rolled on four high universal mill, so it is also called 'universal I-beam'. Ordinary I-beam and light I-beam have formed national standards.Word of mouth recommendation, Remove defective pipes within the allowable length. The tensile strength of seamless pipe is more than ~ times that of ordinary steel, the elastic coefficient is better than that of steel, and has good creep resistance, corrosion resistance and seismic resistance.Because the section size of ordinary I-beam and light I-beam is relatively large and narrow, the moment of inertia of the two main shafts on the section is quite different, which limits its application range. I-beam shall be selected according to the requirements of design drawings. In the structural design, the use of I-beam should be reasonably selected according to the mechanical properties, chemical properties, weldability and structural size of I-beam.lucky charm,Passivation treatment operation of alloy pipeThe import and export order of I-beam is generally based on the specifications required in use after determining the corresponding carbon structure steel (or low alloy steel) steel grade. Except for the specification number, I-beam has no specific composition and performance series.I-beam can be divided into four types according to shape: cold-formed equal edge I-beam, cold-formed unequal edge I-beam, cold-formed inner crimping I-beam and cold-formed outer crimping I-beam.