Fourth, wear resistance means that it is not easy to scratch with artifact.Some people say that this method is unscientific and laminate floors can&#;t soak in water, but I have done some experiments and come to another conclusionEmmen,Moreover, the formaldehyde in the floor mainly comes from the adhesives and coatings used in production.In order to improve the hardness of the board and have the effect of insect prevention and anti-corrosion, most artificial boards use urea formaldehyde resin as the adhesive. The main component is formaldehyde, and residual formaldehyde is inevitable.The environmental protection grade of domestic flooring is divided into E, E and E Only the flooring reaching grade E has a formaldehyde emission of no more than mg/l,EmmenCost effective laminate flooring, which meets the requirements of national standards.Needless to say, for a long time, the lacquered cloth market was occupied by low-grade unlined lacquered cloth produced in Taiwan and other overseas countries, giving consumers the wrong message that China&#;s quality is not up to standard. In fact, after the inspection of these, the surface wear-resistant layer is only .mm which is made of poorly processed and Recycled PVC. It does not meet the national standards for plastic coiled materials at all, so its service life is short, not comfortable to use.Watford,The first is cleaning to remove oil stains or dust;The second is leveling. The convex part shall be shoveled and polished. The concave part can be made into paste with glue and cement at the weight ratio of :, leveled with a spatula, and then leveled with sandpaper after drying.After the ground is flat, clean and dry, it can be glued and paved.Gluing is the last process before paving, and the tool shall be a toothed rubber scraper.During gluing, glue shall be applied on the ground according to the size of the floor paint cloth, and one piece shall be paved in this order.A width of cm shall be reserved at the joint of the floor paint cloth. No glue shall be applied first, it can be paved. When pasting, pay attention to aligning the sidelines, and use a long handle floor brush to blow out and compact.The joints are generally spliced by overlapping cutting, and the overlapping width is about cm.Align the long steel ruler with the center of the overlap, then remove the cut edge strips (note that there should be two edge strips, don&#;t forget to take out the lower one), apply an appropriate amount of glue to the joint with a paint brush, and then close and compact the joint with a pressing roller.The residual glue extruded at the joint shall be wiped clean to avoid affecting the appearance.Then apply a thin layer of joint liquid along the joint.Finally check whether there are bubbles and whether they are flat.If there are bubbles, use a syringe to insert and suck out the air, and then compact it.Finally, use washing powder to remove the residual glue marks on the lacquer cloth. If they cannot be removed, they can be wiped with alcohol.In this way, the whole process will be completed.Due to the improvement of the living standards of Chinese residents, the grade of interior decoration is also rising, and the decoration materials are increasingly developing towards the fixed decoration direction of elegance, high profile, long service life and good effect.As for the ground, the service life of paint, carpet or ordinary floor leather and floor brick is not as long as that of ground lacquer cloth.Whether it is solid wood composite floor or solid wood floor, its surface needs to be maintained and does not want to strengthen the surface of the floor.When cleaning the solid wood floor, remember not to wipe the solid wood floor directly with wetland.Please choose a special detergent for wood floor cleaning to keep the wood floor in its natural primary color and prevent the wood floor from cracking. Various surface treatments (concave convex pattern, hand grip pattern, pair pattern mirror pattern)

However, SPC floor and plastic are not the same thing at all. SPC floor does not need glue in the production process does not contain toxic substances such as formaldehyde and benzene, and does not have radiation. It is a green environmental protection decoration material and will not cause harm to human body. Select water resistance. Pay attention to the size.Supply chain quality management, Water resistanceThe flame retardant grade is B, and the formaldehyde concentration is acceptable.Precautions for solid wood floor installation : prevent uneven ground.The first is cleaning to remove oil stains or dust;The second is leveling. The convex part shall be shoveled and polished. The concave part can be made into paste with glue and cement at the weight ratio of :, leveled with a spatula, and then leveled with sandpaper after drying.After the ground is flat, clean and dry, it can be glued and paved.Gluing is the last process before paving, glue shall be applied on the ground according to the size of the floor paint cloth, and one piece shall be paved in this order.A width of cm shall be reserved at the joint of the floor paint cloth. No glue shall be applied first, so that the joint can be treated finally.When the glue coated on the ground feels sticky by hand, it can be paved. When pasting, pay attention to aligning the sidelines, and the overlapping width is about cm.Align the long steel ruler with the center of the overlap, cut with a cutter along the ruler, then remove the cut edge strips (note that there should be two edge strips, don&#;t forget to take out the lower one), apply an appropriate amount of glue to the joint with a paint brush, and then close and compact the joint with a pressing roller.The residual glue extruded at the joint shall be wiped clean to avoid affecting the appearance.Then apply a thin layer of joint liquid along the joint.Finally, check whether there are bubbles and whether they are flat.If there are bubbles, use a syringe to insert and suck out the air, and then compact it.Finally,EmmenHow much is the composite floor? One square meter, use washing powder to remove the residual glue marks on the lacquer cloth. If they cannot be removed, the whole process will be completed.Due to the improvement of the living standards of Chinese residents, the grade of interior decoration is also rising, and the decoration materials are increasingly developing towards the fixed decoration direction of elegance high profile, long service life and good effect.As for the ground, the service life of paint, carpet or ordinary floor leather and floor brick is not as long as that of ground lacquer cloth.

Is the home floor paved with solid wood or structurally reinforced floor?Fair price, Super wear resistanceSeventh, sound insulation and noise reduction.At the same time, for those who pursue value, SPC fine floor is also a good choice.The price of this floor is reasonable but fashionable.The best choice.Emmen,From the front,EmmenTunnel waterproof board, the relief surface is no different from the crystal surface. From the side, touch it with your hand, and there are wood grain patterns on the surface.I have seen the evaluation video before. Netizens rub the steel ball of cleaning tableware back and forth on the SPC floor, and there is no trace on the surface.If it&#;s a wooden floor, I think it&#;s not like it anymore. You can see how good its wear resistance is.WPC wood flooring is amazing in touch.It&#;s thick, so you&#;ll feel comfortable under your feet.Great stability.When you walk on the floor, you will feel that it has been buffered.The thickness of the floor has good thermal insulation, so the floor will remain warm in the cold season.