The characteristics of square pipe are as follows: the production process of square pipe is simple, the production efficiency is high, and square pipe with different pipe diameter with blank of the same width. However, compared with straight seam pipe of the same length, the weld length is increased by ~, which will be oriented to the whole country for a long time Individuals and enterprises provide all kinds of square tubes, square rectangular tubes, seamless square tubes,MonacoHow much is 80 galvanized pipe, galvanized square tubes, galvanized tubes, on-site settlement, honest operation, local offices, long-term cooperation, and low production speed. Therefore, most of the smaller square tubes adopt straight seam welding and most of the large-diameter square tubes adopt spiral welding.Generally speaking, square pipe welding has a process: ignition, pressurization and thermal insulation.MonacoHDPE plastic square pipe made according to the properties of square pipe has the advantages of light texture, high strength, good resistance, easy laying, low water resistance, low cost and corrosion resistance. Its service performance and economic benefits far exceed reinforced concrete pipe and general specification iron pipe. It is an updated product of engineering pipe.According to smelting classification and furnace type, A. open hearth steel: (a) acid open hearth steel; (b) Alkaline open hearth steel.Alemana townProduct description of square tube square tube is a light thin-walled steel tube with hollow square section, also known as steel cold-formed profile. It is a section steel with square section shape and size, which is made of Q hot-rolled or cold-rolled strip or coil as the base material, cold bending and high-frequency welding. In addition to wall thickness thickening, the corner size and edge flatness of hot-rolled special square pipe reach or even exceed the level of resistance welding cold-formed square pipe. Good comprehensive mechanical properties, weldability, cold and hot workability and corrosion resistance, and good low temperature toughness.For transportation: water supply, drainage, sewage treatment engineering, mud transportation, marine water transportation.For gas transmission: gas, steam and liquefied petroleum gas.

With the progress of the times and the development of science and technology, the application fields of square tubes are widely divided. The main fields are the construction industry. Affected by the environment and weather, and qb square tube factory continues to extend in the technical level which makes the current square tube develop more widely.The square tube is divided into a. boiling steel according to the degree of deoxidation and pouring; b. Semi killed steel; c. Killed steel; d. Special killed steel. The deformation of qb square tube is mainly caused by the shrinkage force of the weld greater than the strength of the base metal.A complete range of products,The floating mandrel mill is in its heydayIt should be noted that the position of the disc from the calibration line can be adjusted according to the reinforcement diameter,MonacoGalvanized square pipe, each, and R and R can be equal or different.Large diameter qb square tube production standard classification square tube is divided according to production standard: national standard square tube, Japanese standard square tube, British standard square tube, American standard square tube, European standard square tube and non-standard square tube.

The surface of fake and inferior square tubes is easy to produce scabs. There are two reasons: the material of fake and inferior square tubes is uneven and there are many impurities. The guide equipment of fake and shoddy material manufacturers is simple and easy to stick to steel. These impurities are easy to scar after biting the roll.Welcome calls ,After cold drawing and aging treatment, the yield point is improved, the tensile ultimate strength is also increased, and the plasticity continues to decrease. Due to the reduction of internal stress during aging, the modulus can be basically restored. According to this principle, cold drawing or cold drawing of reinforcement or low carbon steel wire rod is often carried out on site or prefabricated component factory, it is necessary to distinguish the carbon equivalent of the qb square tube, and the carbon equivalent of the qb square tube is the same. If the carbon equivalent of Q is less than .%, it can be said that the weldability is OK. Generally speaking, the cold crack increases when the carbon equivalent is .%.C. special performance steel: (a) stainless and acid resistant steel; (b) Heat resistant steel; (c) Electric heating alloy steel; (d) Electrical steel; (e) High manganese wear resistant steel.Monaco, the carbon content generally does not exceed %. In addition to iron and carbon, the main elements of steel also include silicon,MonacoElectro galvanized square pipe, manganese, sulfur, phosphorus, etc. There are various classifications of steel and square tubes, mainly including the following: square tubes are classified into ordinary steel according to quality (P & le; .%, S & le; .%)Oil drilling pipe (yb-) is a square pipe used for internal or external thickening at both ends of oil drilling. Steel pipes are divided into turning wire and non turning wire. Turning wire pipe is connected with joint, and non turning wire pipe is connected with tool joint by butt welding.Square tube, modified square tube, square tube, QB square tube and hot-rolled square tube are qualified in quality inspection. The manufacturer adopts advanced equipment to ensure the quality of each product. Magnetic flux leakage testing for surface defects of square tubes is very similar to magnetic particle testing for square tubes, and its scope of application, sensitivity and reliability are stronger than magnetic particle testing. Indirect square forming process the traditional forming process of cold-formed square pipe is to gradually roll the hot-rolled steel coil multi stand forming unit into round pipe at room temperature, which is called indirect square forming process. The traditional roll forming process uses the method of fixed bending point position and variable bending radian to complete the corner forming of pipe blank, which is suitable for rolling small and medium-sized products. Rolling with this process & ldquo; Superb & rdquo; Square tube will show its inherent defects. Because the roll work in the bending process of this process is always concentrated at the point, excessive stress concentration often shows microcracks in the bending process of profiles, which will lead to cracking in serious cases. The products with such defects have serious consequences when they are used in building steel structures. The study of the broken square tube column in the Hanshin earthquake in Japan shows that the corner microcrack is the main cause of the square tube fracture. At the same time, due to the different forming bending radians of products with different wall thickness, the universality of rolls is limited. The large-size cold-formed square tube used in the process adopts the advanced & ldquo; Direct Square & rdquo; The production process is to directly roll the hot-rolled steel coil into a square and rectangular shape at room temperature.