The pickling agent in the pickling process contains many acidic substances, including hydrochloric acid, sodium cyanide, etc., which has strong corrosion and reduction, and the temperature of etching substances is relatively high. Therefore, the corrosion resistance of alloy pipes is specified higher.The utility model has the advantages that the axial force of the roll is small, the axial movement is small, the working inclined plane is not required, the pass occupies a small length of the roll body, and more passes can be matched under the condition of a certain length of the roll body.Barilas,Idler pipe: it is used for electric welding steel pipe of idler of belt conveyor. It is generally made of Q, QA, B steel and steel, with a diameter of -mm. There are certain requirements for pipe tortuosity, end face straightness with the center line and ovality. Generally, water pressure and flattening tests are carried out.So why is the alloy pipe easy to rust after being pickled and passivated by the software?Jieyang City,Key technical characteristics of alloy pipe:H-section steel belongs to high-efficiency and economic cutting profile (other cold-formed thin-wall section steel, profiled steel plate, etc.). Due to the reasonable section shape, they can make the steel give more play to its performance and improve the cutting capacity. Different from ordinary I-type, the flange of H-section steel is widened, and the inner and outer surfaces are usually parallel, so it is convenient to connect with other components with high-strength bolts. Its size composition is reasonable, series and models are complete, which is convenient for settingX-ray or ultrasonic testing shall be carried out for repair welding of alloy pipe, dead end welding of strip steel and circumferential seam. For the spiral welding of steel for the transportation of flammable general liquids, wastewater, gas, heating steam and other general liquids, X-ray or ultrasonic testing sampling inspection (%) shall be carried out.

I-beam has the dual properties of high hardness and toughness materials. Compared with other engineering wear-resistant materials in China, such as various alloy steel plates, cast wear-resistant plates, cast stones, rubber, polyurethane, etc. it has irreplaceable comprehensive excellent properties.Classification by end shape The small length of repair welding is mm; The raw material shall not exceed mm after grinding by welding edge.assets,What are the uses of I-beam?Main uses: as a finished material, flat steel can be used to make hoop iron, tractors, railway transportation and other machinery.b. The professional two-sided arc welding processing technology can complete the electric welding at a good position, welding deviation and incomplete penetration and it is very easy to manipulate the welding quality.

Whether I-section steel is ordinary or light, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different so it can only be directly used for members bent in the plane of their web or form lattice stressed members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application. I-beam is widely used in buildings or other metal structures.Test conclusion,Methods of exerting efficiency in application of C-section steelLongitudinal welded pipe has the advantages of simple production and processing technology, high production efficiency, low cost and rapid development trend. The compressive strength of spiral welded pipe is generally higher than that of straight welded pipe. Narrow blank can be used to produce welded pipe with large pipe diameter,Barilas45crmo alloy pipe, and blank with the same total width can also be used to produce welded pipe with different pipe diameter. However, the welding length is increased by ~ , and the production rate is low.Under the action of thermal stress,BarilasGb5310 quotation of seamless pipe, because the initial temperature of the surface layer is lower than that of the heart and the shrinkage is greater than that of the heart, the heart is pulled. At the end of cooling because the final cooling volume shrinkage of the heart cannot be carried out freely, the surface layer is compressed and the heart is pulled. That is, under the action of thermal stress,BarilasHigh pressure alloy pipe, the surface of the workpiece is finally compressed and the center is pulled. This phenomenon is affected by factors such as cooling rate, material composition and heat treatment process. The faster the cooling rate, the higher the carbon content and alloy composition, the greater the uneven plastic deformation caused by thermal stress during cooling, and the greater the final residual stress. On the other hand, due to the change of microstructure during heat treatment, i.e. the transformation from austenite to martensite, the increase of specific volume will be accompanied by the expansion of workpiece volume, and each part of workpiece will undergo phase transformation successively, resulting in inconsistent volume growth and structural stress. The final result of the change of tissue stress is the tensile stress on the surface and the compressive stress in the center, which is just opposite to the thermal stress. The microstructure stress is related to the cooling rate, shape and chemical composition of the workpiece in the martensitic transformation zone.Barilas,b. The professional two-sided arc welding processing technology can complete the electric welding at a good position, which is not easy to have the disadvantages of staggered joint, welding deviation and incomplete penetration and it is very easy to manipulate the welding quality.The pickling agent in the pickling process contains many acidic substances, including hydrochloric acid, sodium cyanide, etc., which has strong corrosion and reduction, and the temperature of etching substances is relatively high. Therefore, the corrosion resistance of alloy pipes is specified higher.Performance parameters and application scope of I-beam