Submersible slurry pump In addition, which also requires some time og quantity when switching on and off, so in fact, it can be adjusted to a certain extent during use. The submersible slurry pump needs to use a line when in use First of all, lets understand the causes of insufficient liquid supply: If the liquid level stored in the circulating liquid storage tank is lower than %, then insufficient liquid supply will occur when it is in use. Or the pump adds too much lubricating oil, which leads to accumulationKapshagai, On the basis, according to the type selection requirements of different transmission media and temperatures, it extends IRG vertical hot water circulating pipeline centrifugal pump,KapshagaiWQ submersible sewage pump, GRG vertical high temperature pipeline pump, IHG vertical chemical centrifugal pump, YG vertical pipeline centrifugal pump, ihgb vertical explosion-proof stainless steel pipeline centrifugal pump and isgb explosion-proof pipe Where ρ—— Density of transmission medium liquid (kg/m; γ—— Gravity of medium liquid (n/m; H -- pump lift (m); Q - water pump flow (m/s); G - gravitational acceleration (m/s. The difference between the shaft power P and the effective power PE is the power loss in the pump,KapshagaiVertical centrifugal slurry pump, which is measured by the pump efficiency. The pump efficiency is the ratio of the effective power and the shaft power, which is measured by η Indicates.Muharrak, No matter what type of slurry pump you need, Ritter pump will provide you with high-quality slurry pump products; New progress in submersible slurry pump technology in recent years The diving depth has increased from meters to meters! Some corrosive pastes containing crystals can also be transported. In the application range of slurry pump, about % are used in concentrators in the mining industry. Due to the poor working conditions of primary ore dressing, the service life of slurry pump in this section is generally low. Of course different minerals, bearing puller (commonly known as triangle puller) abrasion First remove the pump from the engine.
Prepare tools and materials: a set of metric box / open-end wrench, magnetic dial indicator, outside micrometer, caliper, square ruler, copper bar, screwdriver with handle, hammer, V-shaped irons of the same specification, clean kerosene, cotton yarn, etc. Change the oil: if the oil contains water, drain it change the oil, seal the gasket, and then tighten the screw plug. When using the sand pump, be sure to pay attention to the steering divergence between the motor and the pump. The sand pump has an arrow on the pump to mark the main steering. After the power supply is connected, be careful not to exceed the bearing on the pump support to avoidWhere to sell API, Why does the demand for submersible slurry pumps increase greatly? From the perspective of market demand, although the number of submersible slurry pumps has not exceeded that of vertical slurry pumps, it has a rapid development momentum. The main reason is that the above-mentioned use is convenient and flexible; In addition, the application market of submersible slurry pump is also better than that of vertical pump Submersible slurry pump is a kind of pump used in mines. Do you know the effect and form of its shaft seal? Lets have a look. Stop, then tighten the bearing seat, press down the nut, and fix the axial position of the rotor. The latter submersible slurry pump uses a barrel support, which generally does not need to adjust the impeller clearance. Therefore, if there is a problem with the clearance in the future use, loosen the support clamp first, and say that the nut is loose
It is also possible that the fan blades of the pump are few and the air volume is insufficient, resulting in poor heat dissipation effect.Product line, Although the shaft seal occupies a small position in the pump,KapshagaiZD slurry pump, the normal operation of the pump is closely related to the shaft seal. The main shaft of the water pump is bent or the main shaft of the water pump and the motor is not concentric or parallel. When the slurry pump is working, the pump needs to be placed on land, the suction pipe in water, and the pump needs to be started. Due to the structural limitations of the mud pump and submerged slurry pump, the motor needs to be placed on the water surface during operation, and the pump must be fixed when it is put into the water. Otherwise, the motor will fall into the waterKapshagai, Where ρ—— Density of transmission medium liquid (kg/m; γ—— Gravity of medium liquid (n/m; H -- pump lift (m); Q - water pump flow (m/s); G - gravitational acceleration (m/s. The difference between the shaft power P and the effective power PE is the power loss in the pump, which is measured by the pump efficiency. The pump efficiency is the ratio of the effective power and the shaft power, which is measured by η Indicates. In this way, a smooth surface can be formed on the surface. the submersible slag pump is often used to transport pulp containing solid particles so the wear resistance of the pipeline should also be considered.