Ensure good power supply at the installation site, install a separate distribution box, and the leakage switch must meet the requirements for construction elevators when used in the distribution box. If the construction elevator installed is frequency conversion, the leakage switch should be adapted to the frequency converter when selecting the leakage switch .Guide rail lift (also known as freight elevator) is a non-scissor hydraulic lifting platform, which is mainly used in industrial plants, restaurants, restaurants, warehouses, docks, workshops and other places that need to move goods vertically between high-rise buildings above the second floor. The low height is especially suitable for sites where the site is not suitable for digging pits. What problems do we need to pay attention to in these places where elevators are used?Riverside Seine,The guide mechanism of the guide rail elevator manufacturer is mainly composed of guide plastic tube, guide bracket, compression spring, safety plug, guide shell and guide shaft. The lifting cloth belt protrudes from the box through this narrow slit to prevent the cloth belt from being rolled up and play a guiding role. The safety plug is supported by a guide bracket and a compression spring. In order to prevent the compression spring from losing stability after being stressed, a small guide rod is designed on the safety plug. The gap between the small guide rod and the spring is designed with reference to the table. The boom shaft is welded, and a boom hook is installed at both ends. The material is selected and quenched and tempered. It forms three suspension points with the hook of the lower shell of the box. The soft support spreader will be hoisted by the lifter. Bearing weight of the arm, in order to make the person being lifted in a comfortable state when riding, the reference table for the distance between the hooks of the two booms lists the relevant data of the horizontal dimension as a design reference, the balance bar is used to maintain the balance of the lifting device, and the material is designed to be The hollow tubular shape reduces the overall weight of the boom.System: explosion-proof electronic control system, remote control system, P IC system.Dilling,Regarding the cleanliness of the hydraulic station, is there any relevant rule requirement?Frequently check the humidity of the aerial work vehicle that is prone to water accumulation. It is inevitable that the aerial work vehicle is driving in rainy and snowy weather, or on muddy roads. The bottom and some gaps and indoor floors are easy to accumulate sludge. If the owner does not clean it in time this will hide the moisture. Therefore, the outer edge of the wheel hub, the door, the corner of the bottom of the trunk, the key hole and the wiper frame and other areas should be checked regularly, and the drainage holes in the door and various parts should be kept unblocked to ensure that the car seat covers, carpets and floors are protected from humidity. Rusty fittings.Uses: The scissor-type fixed lifting platform is mostly used for the transportation of goods between the height differences of the production line, the loading and unloading of materials, the adjustment of the working height during the assembly of the workpiece, the feeding of the installed machine at a high place, the lifting of parts during the assembly of large equipment, and the storage and unloading place and Forklifts and other handling vehicles are used for fast loading and unloading of goods, car lifting, fixed three-dimensional parking and other places.

The daily maintenance of the hydraulic lifting platform in normal use is essential, but even if there is normal maintenance on the equipment, any possible problem cannot be ignored, so in order to ensure that the process of using the hydraulic lifting platform for each operation What aspects do we need to check before operation? Today, the editor will give you a popular science.The purpose of the stage lift: The telescopic stage adopts an effective guiding system, so that the gap between the telescopic stage and the fixed stage is small during the translation process the operation is stable, and the speed changes steplessly. The synchronous device is driven by low speed and high torque, so that the stage can be paralleled, freely stretched and stretched in place during the expansion and contraction process, and can automatically achieve leveling. It is suitable for cultural and entertainment places such as auditoriums, theaters multi-functional halls, studios, cultural stadiums, hotels, etc.The wrong connection of the motor of the elevator When a coil, coil group or one-phase winding is reversed,The design of the hydraulic lifting platform is unreasonable. When the designer designs the cylinder barrel and rod,Riverside SeineTwo ton lifting cargo elevator, if there is a problem with the design size and angle, then there will definitely be problems in the later stage. Therefore, it is necessary to confirm the technical strength of the manufacturer when working on a hydraulic lifting platform; what is the problem with the sound of the oil cylinder of the hydraulic lifting platform? Design drawings to make, the angle of the oil cylinder is slightly deviated, it will cause the friction between the cylinder barrel and the rod, which will cause the sound; the seal quality of the hydraulic lifting platform is different, and the seal with excellent material The continuous friction between the parts and the cylinder wall will cause the sound to be very loud, and long-term wear and tear may scratch the oil cylinder and cause oil leakage, so when the hydraulic lifting platform is used, pay attention to ask the manufacturer what brand and material the seal is used; In some cases of mechanical running-in, it is not ruled out that the above three situations are normal, and there will still be noises. If there is no problem after investigation, then don’t worry. It’s just a running-in problem between mechanical parts. It will disappear naturally.Features of hydraulic lifts: According to the working mode, hydraulic lifting platform products are divided into crank arm hydraulic lifting machines, scissor hydraulic lifting machines, mast type hydraulic lifts, and straight arm hydraulic lifting machines. The hydraulic lift is a replacement product of the folding arm lift (lifting platform) and the scissor lift (lifting platform). It can be widely used in stations, docks, airports, post and telecommunications, municipal gardens, garages, cleaning companies, public building facade decoration, decoration or installation and maintenance of power systems,Riverside SeineCargo elevator, etc. The lift has the advantages of light weight, self-propelled, electric start, self-supporting legs, simple operation, large working area especially the ability to cross obstacles for high-altitude operations and the like.The surface of the brushes of each part should be kept clean, large quantity favorably and the pressure of the brushes should be adjusted so that the area is not less than %. Professional elevator factory, high quality and low price. Fire-resistant-waterproof-high temperature resistant, durable, safe and reliable.

Today, the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.Quality improvement,Pay attention to check whether there are any broken wires and loose strands in the wire ropes of each part. If it exceeds the relevant regulations, it must be replaced immediately. The maintenance of the wire rope should be strictly in accordance with regulations.The one-way valve is damaged. The one-way valve is to prevent the oil from returning. If there is a problem, so it can be replaced with a new one at this time.The water cooling of the hydraulic station is generally tube-type water cooling, and its type selection is based on the heat load to calculate the heat exchange area, while its air-cooled elevator is carried out by using an air cooler, and it is The heat transfer capacity is calculated according to the heat load, and then the type selection calculation is carried out under the condition that the flow rate can be satisfied. Therefore, and there is a big difference. Long-term promotion of freight elevator factories and other, Long-term cooperation, mutual benefit and win-win. If you choose the wrong supplier, you will be overwhelmed with all kinds of after-sales troubles in the later stage. Recently, I have seen many netizens report the problem of very loud oil cylinders. Today,Riverside SeineGuide rail lifting cargo elevator lifting, the editor will simply popularize the knowledge for everyone.Riverside Seine, from a professional point of view so it should not be careless. Moreover, there are relevant rules and requirements, and you should refer to the specification manual, so that you can have a correct understanding and know how to achieve better cleanliness.The safety device of the guide rail hydraulic lifting platform The mechanical part of the guide rail hydraulic lifting platform mainly includes the hydraulic system and the mechanical device.Brake operators of various mechanisms on the equipment should regularly check and adjust the gap between the brake shoe and the brake wheel to ensure flexibility and reliability. Long-term promotion of freight elevator factory, old brand, price advantage

It is strictly forbidden for personnel to take the freight elevator to go up and down floors and climb.The last thing to note is that, compared with the lifting platforms in some places, protective fences are generally added on the platforms. Since the lifting platforms are special equipment, the National Quality Inspection Bureau is very strict on this piece of inspection. All must be dismantled, so when the personnel ask you if you want to add a guardrail, don't blindly refuse, and consider whether it is necessary according to the site of use. In addition, you must have the 'People's Republic of Special Equipment Manufacturing License' and the 'People's Republic of Special Equipment Installation, Transformation and Maintenance License' to produce, install, and maintain. Therefore, you must ask whether the manufacturer has these two certificates.Limerick, safe the design structure is reasonable and compact, stable and reliable built-in safety valve, fully sealed oil cylinder, manual hydraulic system lifting, easy to operate. Equipped with guide wheels to save the operator's physical strength, and can protect the load wheels and pallet load wheels. Unique hydraulic pump design, the pump is simple and designed to maintain an ideal height for assembly line loading and unloading operations; coupled with the unique design concept, the operator's operation is simple and convenient.Outriggers: mechanical outriggers, hydraulic outriggers, ordinary hand-operated outriggers pull-out outriggers.Vennesla,Hydraulic pump station: special pump station for domestic lifting platform, protection device outside the pump station imported from Italy: organ m type, mesh type, iron plate seal type.Precautions for elevator installation Keep the access road of the external construction elevator smooth and have enough parking space for equipment. When it is necessary to use a steam crane for auxiliary installation, it should be fully considered whether the site environment meets the operating conditions of the steam crane.Anti-corrosion measures for the body of aerial work vehicles Pay attention to small scratches. The paint surface of aerial work vehicles is often corroded. In addition to common collisions scratches, small rocks on the driving tires, there may also be a peeling paint spot, and a small rust will appear after a long time. Because most of these scars are small, they are easy to ignore. Therefore, check regularly, and once found, go to a professional beauty shop for processing.

Frequently check the humidity of the aerial work vehicle that is prone to water accumulation. It is inevitable that the aerial work vehicle is driving in rainy and snowy weather, or on muddy roads. The bottom and some gaps and indoor floors are easy to accumulate sludge. If the owner does not clean it in time, this will hide the moisture. Therefore, the outer edge of the wheel hub, the door, the key hole and the wiper frame and other areas should be checked regularly, and the drainage holes in the door and various parts should be kept unblocked to ensure that the car seat covers, carpets and floors are protected from humidity. Rusty fittings.Adjust the helmet lining of the helmet before using the helmet, and keep a certain space between the helmet lining and the helmet shell.The anti-rust work of the aerial work vehicle generally needs to be paid attention to when the aerial work vehicle has not been used for a long time. How should we do anti-corrosion for the body of the aerial work vehicle? This is actually very simple. You don’t need to spend money to go to the repair station for anti-corrosion. As long as our car owners use some materials that they can find at hand, it can be realized. At the same time, paying attention to driving habits can ensure that the aerial work vehicle does not rust. Here are a few points that can be used as a reference.Installation materials,LimerickSimple track lifting cargo elevator,Whether it is used outdoors or indoors, some small problems will inevitably appear after a long period of time. At this time, what we should do is to maintain and maintain the elevator. How to follow the steps correctly It has become a difficult problem, it must be replaced immediately. The maintenance of the wire rope should be strictly in accordance with regulations.Ensure good power supply at the installation site, install a separate distribution box, and the leakage switch must meet the requirements for construction elevators when used in the distribution box. If the construction elevator installed is frequency conversion, the leakage switch should be adapted to the frequency converter when selecting the leakage switch .

The common types of lifts are simply introduced here for you. I hope you can learn more about this product. At present, this product can be said to be sold well in China, because many places need to use this product. Products that can be lifted and moved flexibly at the same time. Now companies that specialize in the production of this product combine a large-scale external publicity on the Internet. Friends in need can directly find the corresponding company on the Internet,Limerick3 ton fixed lifting cargo elevator, and then simply learn about the models of these products and Information on performance and price can be purchased directly through the Internet.Let's see,Guide rail lift (also known as freight elevator) is a non-scissor hydraulic lifting platform, which is mainly used in industrial plants, restaurants, restaurants,LimerickHydraulic guide rail type cargo elevator, warehouses, workshops and other places that need to move goods vertically between high-rise buildings above the second floor. The low height is especially suitable for sites where the site is not suitable for digging pits. What problems do we need to pay attention to in these places where elevators are used?Today, the temperature in Shandong suddenly dropped, catching office workers and the public by surprise. Dear friends, you must remember to add more clothes when you go out. Shandong is the hometown of elevators in China. There are countless large and small manufacturers. So, how to maintain the lifting stage and the elevator after entering the winter. Below is a detailed introduction for you.Unscrew the screw on the dust-proof hole outside the flange of the elevator, adjust the PCS system ring to align the side hole with the dust-proof hole, and tighten the inner hexagon. After that, remove the motor shaft key.Limerick,What types of lifts are there? There are many types of this equipment, for example, it can be divided into fixed lifting devices and vehicle-mounted lifting devices according to the form of movement. The so-called fixed lifting means that it is generally installed in one place and fixed, and then the lifting operation can be carried out. This type of lifting equipment is generally used more on the assembly line. Some large-scale production lines need to move the material when loading materials. Lifting to a certain position, and then putting it into the production line for production, a special lifting device is required to be fixed at a certain position of the production line.It is strictly forbidden for personnel to take the freight elevator to go up and down floors and climb.This kind of fixed lifting equipment can also be used in the warehouse. For example, a certain floor in the warehouse needs to be lifted to send goods or personnel into the designated warehouse.

Frequently check whether the various mechanisms are operating normally and whether there is any noise. If a fault is found, it must be eliminated in time.The safety device and application of the guide rail hydraulic lifting platform The use of the guide rail hydraulic lifting platform The guide rail hydraulic lifting platform is a non-scissor hydraulic lifting freight elevator. It is used for goods between different floors of industrial plants, restaurants, restaurants, etc. The low height can be made to -mm. The advantage is that it can be placed directly on the ground without digging pits, reducing engineering construction costs, and there is no need to set up hanging points on the top, which is safe. Reliable; the hydraulic lifting platform adopts hydraulic transmission mode, and can be non-calibrated according to customer needsSeveral types: Motor winding open circuit. When one of the motor windings is disconnected, or one of the parallel branches is disconnected the three-phase current will be unbalanced and the motor will overheat.Kessley,The guide mechanism of the guide rail elevator manufacturer is mainly composed of guide plastic tube, guide bracket, compression spring, safety plug, guide shell and guide shaft. The lifting cloth belt protrudes from the box through this narrow slit to prevent the cloth belt from being rolled up and play a guiding role. The safety plug is supported by a guide bracket and a compression spring. In order to prevent the compression spring from losing stability after being stressed, a small guide rod is designed on the safety plug. The gap between the small guide rod and the spring is designed with reference to the table. The boom shaft is welded, and a boom hook is installed at both ends. The material is selected and quenched and tempered. It forms three suspension points with the hook of the lower shell of the box. The soft support spreader will be hoisted by the lifter. Bearing weight of the arm, in order to make the person being lifted in a comfortable state when riding, the reference table for the distance between the hooks of the two booms lists the relevant data of the horizontal dimension as a design reference, the balance bar is used to maintain the balance of the lifting device, and the material is designed to be The hollow tubular shape reduces the overall weight of the boom.The elevator is a kind of elevator equipment composed of traveling mechanism, hydraulic mechanism, electric mechanism and supporting mechanism. The hydraulic oil is under a certain pressure formed by the vane pump, and enters the lower end of the hydraulic cylinder through the oil filter, explosion-proof electromagnetic reversing valve, throttle valve, hydraulic control check valve, and balance valve, so that the upward movement of the hydraulic cylinder can lift heavy objects , and the rated pressure relief valve is adjusted, and the pressure gauge reads the pressure gauge.Bwayogers,Nowadays, small and medium-sized enterprises are holding products with the idea of ​​good quality and favorable price.Brake operators of various mechanisms on the equipment should regularly check and adjust the gap between the brake shoe and the brake wheel to ensure flexibility and reliability. Long-term promotion of freight elevator factory, old brand, price advantage, quality guaranteed!When the freight elevator breaks down,KessleyOutdoor guide rail type cargo elevator, and the freight elevator cannot be altered without authorization.

Precautions for using guide rail elevators Precautions for using guide rail elevators: It is strictly forbidden to overload transport flammable and explosive products and other products.Based on the information you have investigated, choosing a lifting machine with better cost performance should be based on its technical parameters, practicability and versatility. Usually, there are many kinds of aluminum alloy lifting machines, including vehicle-mounted lifts, fixed lifts hydraulic lifts, etc. Lifting platforms, scissor lifts, etc. each have slightly different technical parameters and uses but there are also many similar functions. Therefore, as a customer, you have to choose with a purpose, that is, you buy a mechanical lift What to do, and which kind of lifting machinery can meet your needs and has multiple uses. The last point is that after the equipment arrives, when unpacking and accepting, check whether the accompanying technical information is complete, whether the accompanying accessories, tools, and accessories are consistent with the list, and whether the equipment and Check whether the accessories are damaged, defective etc., and make a record of unpacking and acceptance. The working principle of the aluminum alloy elevator: the hydraulic oil is formed by the vane pump to a certain pressure, and enters the lower end of the hydraulic cylinder through the oil filter, explosion-proof electromagnetic reversing valve, throttle valve, hydraulic control check valve, and balance valve, so that the hydraulic cylinder The upward movement of the cylinder lifts the heavy object, and the oil returned from the upper end of the hydraulic cylinder returns to the fuel tank through the explosion-proof electromagnetic reversing valve. The rated pressure relief valve is adjusted, and the pressure gauge reads the pressure gauge.What is the new price of fixed lifts? Fixed lifts are currently very popular in the market. Due to different manufacturers, different materials, and different brand awareness, the prices are also different. The current price of fixed lifts produced in the domestic market: rated load - tons, height of meters, table size mm *mm, the price is about - yuan; the rated load is - tons, the height is meters, the table size is mm*mm, the price is about yuan. Rated load,KessleyFloor to floor cargo elevator, lift height, table size of each fixed liftDifferent. (Specific bearing capacity and rising height can be customized according to user requirements)Create brilliance,Goods should be stacked on the platform and not tilted. When the freight elevator goes up and down beyond the range of the platform, no one should stand around to watch.The contact opening and closing of the travel switch of each safety device must be reliable, and new and old customers are welcome to come to consult.Executive standard,Safety performance: The lifting structure is made of high-strength manganese steel rectangular tube, and the scissor-type mechanical mechanism is easy to maintain with strong stability and high carrying capacity. The maximum lifting height is about meters, and the maximum load is about tons. .When the distribution box is used, the leakage switch meets the requirements for construction elevators. If the installed fixed elevator is frequency conversion, the leakage switch should be adapted to the frequency converter when selecting the leakage switch.The cleanliness of the hydraulic station is an important aspect of the elevator hydraulic station, so it should not be careless. Moreover, from a professional point of view, there are relevant rules and requirements, and you should refer to the specification manual, so that you can have a correct understanding and know how to achieve better cleanliness.Kessley,What types of lifts are there? There are many types of this equipment, for example,KessleyOrdering Elevators, it can be divided into fixed lifting devices and vehicle-mounted lifting devices according to the form of movement. The so-called fixed lifting means that it is generally installed in one place and fixed, and then the lifting operation can be carried out. This type of lifting equipment is generally used more on the assembly line. Some large-scale production lines need to move the material when loading materials. Lifting to a certain position, and then putting it into the production line for production, a special lifting device is required to be fixed at a certain position of the production line.Guide rail lift (also known as freight elevator) is a non-scissor hydraulic lifting platform, which is mainly used in industrial plants, restaurants, warehouses, docks, workshops and other places that need to move goods vertically between high-rise buildings above the second floor. The low height is especially suitable for sites where the site is not suitable for digging pits. What problems do we need to pay attention to in these places where elevators are used?Before using the aerial work platform, it is necessary to confirm whether the outriggers are well supported, refer to the level beads on the equipment to judge and debug, and then proceed with the operation; the rollers and slideways confirm whether the roller slideways of the hydraulic lifting platform are dry, and if there is When drying the site

Hydraulic pump station: special pump station for domestic lifting platform protection device outside the pump station imported from Italy: organ m type, mesh type, iron plate seal type.The safety device of the guide rail hydraulic lifting platform The mechanical part of the guide rail hydraulic lifting platform mainly includes the hydraulic system and the mechanical device.LadomscoThe open base of the adjustment plate makes it easier to clean up debris.In addition to the fixed mode, the elevator also has a vehicle-mounted mobile type. As the name implies, it combines the lifting equipment with the vehicle-mounted system. Such a lifting equipment is very flexible to move, and of course it is more useful. For example There is this kind of lifting equipment in the airport, and it is also possible to install this kind of equipment in stations or stadiums. Since it can be moved, the scope of operation is not limited to a certain place, and it can be used wherever lifting operations are required. It can be used. For example, when installing outdoor advertisements, the height of some advertisements is relatively high. At this time, mobile lifting equipment can be used to send billboards or staff to the designated height to work. This kind of equipment can also be divided into two types according to the driving mode: hydraulic lifting and electric lifting. The so-called hydraulic lifting is driven by hydraulic oil to reach a specified height. The electric mode is driven by a motor or geared to lift to A certain height, but at present, hydraulic lifting platforms are more widely used.Can GioIn the construction elevator, the switch box also has leakage protection equipment. Its wires and cables are well insulated, without leakage, and the metal threaded is not rusted, and its damage is close to zero. His steel wire rope should comply with the corresponding configuration requirements, the number of broken wires should not exceed the corresponding standard. His pulley movement is very flexible.Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, the lift also has a lot of safety equipment.The hydraulic lifting platform is widely used in the maintenance of industrial and mining enterprises, municipal construction, and decoration of hotels and hotels, with reliable quality and perfect performance.

The water cooling of the hydraulic station is generally tube-type water cooling, and its type selection is based on the heat load to calculate the heat exchange area, while its air-cooled elevator is carried out by using an air cooler, and it is The heat transfer capacity is calculated according to the heat load, and then the type selection calculation is carried out under the condition that the flow rate can be satisfied. Therefore, these two kinds of cooling are not the same, and there is a big difference. Long-term promotion of freight elevator factories and other, Long-term cooperation mutual benefit and win-win. If you choose the wrong supplier, you will be overwhelmed with all kinds of after-sales troubles in the later stage. Recently, I have seen many netizens report the problem of very loud oil cylinders. Today, the editor will simply popularize the knowledge for everyone.The second is that steel will have obvious effects of thermal expansion and cold contraction at low temperatures. Although this property of steel will be taken into account when designing and manufacturing hydraulic lifts, the environment is different. Under low conditions, steel will appear. Some unstable performances, such as increased hardness, decreased toughness, etc. At this time, it is necessary to pay more attention to the maintenance of equipment to keep the key parts in order to avoid dry grinding.Hydraulic pump station: special pump station for domestic lifting platform, protection device outside the pump station imported from Italy: organ m type, mesh type, iron plate seal type.management,LadomscoElectric cargo elevator,The cleanliness of the hydraulic station is an important aspect of the elevator hydraulic station, so it should not be careless. Moreover, there are relevant rules and requirements,LadomscoNew fixed lifting cargo elevator, and you should refer to the specification manual, so that you can have a correct understanding and know how to achieve better cleanliness.Brake operators of various mechanisms on the equipment should regularly check and adjust the gap between the brake shoe and the brake wheel to ensure flexibility and reliability. Long-term promotion of freight elevator factory, old brand,LadomscoFixed lifting cargo elevator, quality guaranteed!How to effectively prevent electric shock by using a hydraulic lifting platform It is very common to add a leakage protector, and the cost is not high. It is both affordable and safe, and can effectively prevent electric shock.

Before the elevator manufacturer connects the motor to the elevator, please make the keyway of the motor shaft perpendicular to the tightening bolt. In order to ensure uniform force, please screw on the mounting bolts at any diagonal position first, but do not tighten them tightly, then screw on the other two mounting bolts at diagonal positions, and then tighten the four mounting bolts one by one. Finally, tighten the tension bolts. All tightening bolts need a torque wrench to fix according to the marked fixed torque data and check whether the lift and lifting platform are used.How should we check the construction site of the construction hoist? you know?Workshop cost, scratches, small rocks on the driving tires, there may also be a peeling paint spot, and a small rust will appear after a long time. Because most of these scars are small, they are easy to ignore. Therefore, check regularly, the engine compartment cover and its surroundings, and once found, go to a professional beauty shop for processing.It is strictly forbidden to combine the two layers of the top lining of the safety helmet into one layer.Knowledge popularization of scissor-type fixed lifting platform Superior performance: equipped with safety devices to prevent overloading of the lifting platform; equipped with protection valves to prevent hydraulic oil pipes from breaking; equipped with emergency descending devices for sudden power failures; Lock safety device.Ladomsco,The last thing to note is that, compared with the lifting platforms in some places, protective fences are generally added on the platforms. Since the lifting platforms are special equipment, so when the personnel ask you if you want to add a guardrail, don't blindly refuse, and consider whether it is necessary according to the site of use. In addition, you must have the 'People's Republic of Special Equipment Manufacturing License' and the 'People's Republic of Special Equipment Installation, Transformation and Maintenance License' to produce, install, and maintain. Therefore, you must ask whether the manufacturer has these two certificates.The water cooling of the hydraulic station is generally tube-type water cooling, and its type selection is based on the heat load to calculate the heat exchange area, while its air-cooled elevator is carried out by using an air cooler, and it is The heat transfer capacity is calculated according to the heat load, and then the type selection calculation is carried out under the condition that the flow rate can be satisfied. Therefore, these two kinds of cooling are not the same, and there is a big difference. Long-term promotion of freight elevator factories and other, Long-term cooperation, mutual benefit and win-win. If you choose the wrong supplier, you will be overwhelmed with all kinds of after-sales troubles in the later stage. Recently, I have seen many netizens report the problem of very loud oil cylinders. Today, the editor will simply popularize the knowledge for everyone.Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, the lift also has a lot of safety equipment.

Many customers think that the operating power supply of the hydraulic lifting platform is below the safe voltage of V,Chula VistaProduction of lifting cargo elevators, there will be no electric shock, but if there is improper operation, it will still be very dangerous. So how can we effectively prevent the occurrence of electric shock accidents? Today, the editor will share safety knowledge with you.Low cost: The cost is much lower than that of the scissor-type mobile lifting platform, so when purchasing a lifting platform, you must consider the scope of use of the lifting platform, the frequency of work,Chula VistaProfessional cargo elevator, the load and other factors to choose a lifting platform that suits the work requirements .Chula Vista,Loose fixing screws of the motor: The motor fan itself makes a sound when it turns. If the screws fixing the motor are loose, coupled with its own vibration, the motor collides with other parts in a way, so it makes a sound; the joints of the pin shafts are dry, lack of oil, iron The rigid friction between the parts and the iron parts will not only damage the parts but also produce abnormal noises, so I still want to emphasize again, pay attention to timely maintenance and frequent refueling; if the hydraulic lifting platform does not rise, there is air in the hydraulic oil, you can open it to exhaust If the hydraulic oil is solidified: just replace the hydraulic oil; oil leakage: check whether there is oil leakage at the joints of each oil pipe, if there is oil leakage, timely manufacturers of hydraulic lifting platforms)Features of hydraulic lifts: According to the working mode hydraulic lifting platform products are divided into crank arm hydraulic lifting machines, scissor hydraulic lifting machines, mast type hydraulic lifts, and straight arm hydraulic lifting machines. The hydraulic lift is a replacement product of the folding arm lift (lifting platform) and the scissor lift (lifting platform). It can be widely used in stations, docks, airports, hotels, post and telecommunications, municipal gardens, garages, cleaning companies, public building facade decoration, decoration or installation and maintenance of power systems, etc. The lift has the advantages of light weight, self-propelled, electric start, self-supporting legs, simple operation, large working area, especially the ability to cross obstacles for high-altitude operations and the like.Fkih Ben Salah,The hydraulic lifting platform is widely used in the maintenance of industrial and mining enterprises, municipal construction, and decoration of hotels and hotels, with reliable quality and perfect performance.As for the guide rail elevator installed outdoors, it is often exposed to rain and sunlight, so special attention should be paid to regular maintenance and inspection to avoid accidents.The hydraulic lifting platform can be divided into: four-wheel mobile type, two-wheel traction type, car modified type, car type, auxiliary self-propelled type, and the lifting height ranges from a meter to s meter.

Avoid working in an environment. In the event of rain, snow and other weather, the use of the hydraulic lifting platform should be stopped to prevent the occurrence of a short circuit, resulting in electric leakage and electric shock; non-professionals are strictly prohibited from disassembling electrical appliances such as hydraulic lifting platforms. In the event of an accident, you can’t disassemble without permission to eliminate the cause. You must report to the manufacturer for repair in time, and the manufacturer will guide you to complete the inspection or send someone to repair it; do not disassemble the appliance without permission! Professional elevator factory guarantees quality, guarantees service. Guarantees quality. Your satisfaction is our pursuit! Welcome to inquire.When using mobile lifts for high-altitude operations, the safety requirements and specifications of the project site must be complied with.Before wearing the helmet, check whether the helmet shell, hat lining, the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.The cheapest,The hydraulic lifting platform can be divided into: four-wheel mobile type two-wheel traction type,Chula Vista1 ton lifting 8-meter cargo elevator, car modified type car type, auxiliary self-propelled type, and the lifting height ranges from a meter to s meter.It is strictly forbidden for personnel to take the freight elevator to go up and down floors and climb.The safety device of the guide rail hydraulic lifting platform The mechanical part of the guide rail hydraulic lifting platform mainly includes the hydraulic system and the mechanical device.

The price is guaranteed, the service is guaranteed, and it is a large-scale logistics and storage equipment service company directly operated by the manufacturer. Since the fixed lift is a mechanical device, the quality and performance of the product must be good. Do not accept the products of some manufacturers whose quality is not up to standard, so as to avoid some safety hazards in use.Variable cost,The hydraulic lifting platform is mainly the pressure transmission of hydraulic oil to realize the lifting function. Its scissor mechanical structure makes the lift stable and the wide operating platform and high carrying capacity make the high-altitude operation wide and suitable for many people work at the same time. It makes high-altitude operations efficient and secure.It adopts a scissor-type mechanical structure, so that the aerial work platform can still move stably when it carries a large weight and rises to a large working height. It is its larger range of high-altitude operations and carrying capacity that make it widely used in various fields. The self-propelled scissor-type aerial work platform can walk quickly or slowly at various heights during operation, and can conveniently and continuously complete operations such as forward, backward, up and down, left and right steering on the operating platform. Make high-altitude operations more efficient and more secure. Therefore, it has received more widespread attention in the market.As for the guide rail elevator installed outdoors it is often exposed to rain and sunlight, so special attention should be paid to regular maintenance and inspection to avoid accidents.Chula Vista,Mechanisms: Mechanisms such as tabletops, track grooves, wire ropes, chains, and pulleys are made of solid materials to ensure safety.The wrong connection of the motor of the elevator When a coil, coil group or one-phase winding is reversed, it will cause a serious imbalance in the three-phase current and cause the winding to overheat.Prepare the foundation according to the foundation plan, pay attention to the alignment, leveling

The motor connection is wrong. When the delta connection motor is wrongly connected into a star shape, the motor still runs with full load, and the current flowing through the stator winding will exceed the rated current, and even cause the motor to stop by itself. If it overheats, it will burn out. When the star-connected motor is wrongly connected into a triangle, or the motor with several coil groups connected in series to form a branch circuit is connected in parallel with two branches, it will cause the winding and core to overheat, and in severe cases, the winding will be burned.Before using the aerial work platform, it is necessary to confirm whether the outriggers are well supported, refer to the level beads on the equipment to judge and debug, and then proceed with the operation; the rollers and slideways confirm whether the roller slideways of the hydraulic lifting platform are dry, and if there is When drying the site,The load capacity of the goods and the tonnage of the goods transported at one time also affect the lifting speed. Reaching the excellent value of the lifting platform for transporting goods is the guarantee of speed. If the goods are too heavy, the speed will be affected. If the goods are too light, install a separate distribution box, and the leakage switch must meet the requirements for construction elevators when used in the distribution box. If the construction elevator installed is frequency conversion the leakage switch should be adapted to the frequency converter when selecting the leakage switch .Begoro,What types of lifts are there? There are many types of this equipment, for example, it can be divided into fixed lifting devices and vehicle-mounted lifting devices according to the form of movement. The so-called fixed lifting means that it is generally installed in one place and fixed, and then the lifting operation can be carried out. This type of lifting equipment is generally used more on the assembly line. Some large-scale production lines need to move the material when loading materials. Lifting to a certain position, and then putting it into the production line for production, or on muddy roads. The bottom and some gaps and indoor floors are easy to accumulate sludge. If the owner does not clean it in time, this will hide the moisture. Therefore, the outer edge of the wheel hub, the door, the corner of the bottom of the trunk, the key hole and the wiper frame and other areas should be checked regularly, and the drainage holes in the door and various parts should be kept unblocked to ensure that the car seat covers, carpets and floors are protected from humidity. Rusty fittings.The price is guaranteed the service is guaranteed, and it is a large-scale logistics and storage equipment service company directly operated by the manufacturer. Since the fixed lift is a mechanical device, the quality and performance of the product must be good. Do not accept the products of some manufacturers whose quality is not up to standard, so as to avoid some safety hazards in use.

The water cooling of the hydraulic station is generally tube-type water cooling, and its type selection is based on the heat load to calculate the heat exchange area, while its air-cooled elevator is carried out by using an air cooler, and it is The heat transfer capacity is calculated according to the heat load, and then the type selection calculation is carried out under the condition that the flow rate can be satisfied. Therefore, these two kinds of cooling are not the same, and there is a big difference. Long-term promotion of freight elevator factories and other, you will be overwhelmed with all kinds of after-sales troubles in the later stage. Recently mutual benefit and win-win. If you choose the wrong supplier, I have seen many netizens report the problem of very loud oil cylinders. Today, the editor will simply popularize the knowledge for everyone.The concept of the hydraulic boarding bridge power system of the boarding bridge, the large oil cylinder lifts the entire equipment slant plate, when it rises to the maximum height, the small oil cylinder starts to work, and the loose-leaf tongue plate is stretched out. The equipment plates are all made of high-quality patterned steel plates and profiles for effective welding ,long lasting.In the construction elevator, the switch box also has leakage protection equipment. Its wires and cables are well insulated, without leakage,BessabaElevating cargo elevator, and the metal threaded is not rusted, and its damage is close to zero. His steel wire rope should comply with the corresponding configuration requirements, and there is no problem of broken strands and diameter reduction. Of course, the number of broken wires should not exceed the corresponding standard. His pulley movement is very flexible.Quality recommendation,The water cooling of the hydraulic station is generally tube-type water cooling, and its type selection is based on the heat load to calculate the heat exchange area, while its air-cooled elevator is carried out by using an air cooler and it is The heat transfer capacity is calculated according to the heat load, these two kinds of cooling are not the same,BessabaChain lifting cargo elevator, and there is a big difference. Long-term promotion of freight elevator factories and other, Long-term cooperation, mutual benefit and win-win. If you choose the wrong supplier, you will be overwhelmed with all kinds of after-sales troubles in the later stage. Recently, I have seen many netizens report the problem of very loud oil cylinders. Today, the editor will simply popularize the knowledge for everyone.Ensure good power supply at the installation site install a separate distribution box, and the leakage switch must meet the requirements for construction elevators when used in the distribution box. If the construction elevator installed is frequency conversion, the leakage switch should be adapted to the frequency converter when selecting the leakage switch .Always check the connections of the various parts of the hydraulic lift,BessabaChain guide rail type cargo elevator, and tighten them if they are loose. The tightness of the connecting bolts of the body should be checked when the body is under pressure.

The last thing to note is that, compared with the lifting platforms in some places, protective fences are generally added on the platforms. Since the lifting platforms are special equipment, the National Quality Inspection Bureau is very strict on this piece of inspection. All must be dismantled, so when the personnel ask you if you want to add a guardrail, don't blindly refuse, and consider whether it is necessary according to the site of use. In addition, you must have the 'People's Republic of Special Equipment Manufacturing License' and the 'People's Republic of Special Equipment Installation, install, and maintain. Therefore, you must ask whether the manufacturer has these two certificates.resources,The motor winding is short-circuited. When a short-circuit fault occurs in the motor winding, the short-circuit current is much larger than the normal operating current, which increases the copper loss of the winding, causing the winding to overheat and even burn out.It is strictly forbidden to use the self-locking device that has been severely impacted.Unscrew the screw on the dust-proof hole outside the flange of the elevator, adjust the PCS system ring to align the side hole with the dust-proof hole, and tighten the inner hexagon. After that, remove the motor shaft key.Bessaba,The anti-rust work of the aerial work vehicle generally needs to be paid attention to when the aerial work vehicle has not been used for a long time. How should we do anti-corrosion for the body of the aerial work vehicle? This is actually very simple. You don’t need to spend money to go to the repair station for anti-corrosion. As long as our car owners use some materials that they can find at hand, it can be realized. At the same time, paying attention to driving habits can ensure that the aerial work vehicle does not rust. Here are a few points that can be used as a reference.It is strictly forbidden to switch the electric control switch with wet hands. Many people tend to ignore this detail. Although the safety voltage of the hydraulic lifting platform is below V, if you touch the power supply with your hands, it may cause lifting failure in light cases, or electric shock accidents in severe cases.It is best not to cover the aerial work vehicle and park the vehicle outside. If it is windy and rainy, the clothing will repeatedly slap the car paint, especially if the car blows sand on the clothes, it will draw many fine scratches on it. Because it will turn black over time. In addition, when the wind does not directly spray powder or clean the sand on the mechanism, but it should be washed with water, and prevent the sand particles on the paint surface from being scratched by the vacuum cleaner.

Many people think that the strength of the elevator itself is relatively high when using the elevator, so they did not strictly follow the installation method in the manual during the installation process, but they do not know that this will cause increased wear and tear of the parts and inflexible operation, and pay attention to the work The installation precautions corresponding to the environment should not be ignored. Correct installation, when you install the elevator,LouisvilleElevating cargo elevator 1-4 floors, and assemble and use it carefully.The boxes and distribution boxes of the hydraulic lift are always kept clean, and the dust on the electrical equipment is cleaned in time.Louisville,What is the pressure of the lifting platform? The movement of the lifting platform has always been our concern now. Our use occasions are uncertain, and most of them are part-time jobs. Therefore, in order to better favor customers, we are constantly researching lifting with good mobility. Platform, which can be used in different occasions, but for some large logistics companies or some enterprise processing plants, which can meet the needs of many customers. This is also In recent years, domestic lifting platforms have been used.When the freight elevator breaks down, professionals should be invited to repair it, and the freight elevator cannot be altered without authorization.Curuzu Cuatia,Safety performance: The lifting structure is made of high-strength manganese steel rectangular tube, and the scissor-type mechanical mechanism is easy to maintain, with strong stability and high carrying capacity. The maximum lifting height is about meters, compared with the lifting platforms in some places, protective fences are generally added on the platforms. Since the lifting platforms are special equipment, the National Quality Inspection Bureau is very strict on this piece of inspection. All must be dismantled, so when the personnel ask you if you want to add a guardrail, don't blindly refuse, and consider whether it is necessary according to the site of use. In addition, you must have the 'People's Republic of Special Equipment Manufacturing License' and the 'People's Republic of Special Equipment Installation, Transformation and Maintenance License' to produce, install, and maintain. Therefore, you must ask whether the manufacturer has these two certificates.It is strictly forbidden for personnel to take the freight elevator to go up and down floors and climb.

Pay attention to check whether there are any broken wires and loose strands in the wire ropes of each part. If it exceeds the relevant regulations, it must be replaced immediately. The maintenance of the wire rope should be strictly in accordance with regulations.The shafts in the middle of the support rods of the hydraulic lifting platform are inconsistent, causing the lifting platform to fail to work normally the platform is severely damaged,LouisvilleFloor to floor cargo elevator, and the table is tilted. Please check carefully that the general scissor aerial work platform has not been strictly tested before leaving the factory, and it has been put into the market. Caused a lot of accidents to take place, for the tilt detection, the detection of this link is not very concerned about for the majority of small enterprises, which is why there are such a large number of lifting equipment to have this problem. Problems with the oil cylinder and the power unit system are often caused by insufficient power and unqualified quality of the oil cylinder which is also a problem that the enterprise itself needs to pay attention to.Before the elevator manufacturer connects the motor to the elevator,LouisvilleTwo ton lifting cargo elevator, please screw on the mounting bolts at any diagonal position first please make the keyway of the motor shaft perpendicular to the tightening bolt. In order to ensure uniform force, but do not tighten them tightly then screw on the other two mounting bolts at diagonal positions, and then tighten the four mounting bolts one by one. Finally, tighten the tension bolts. All tightening bolts need a torque wrench to fix according to the marked fixed torque data and check whether the lift and lifting platform are used.How should we check the construction site of the construction hoist? you know?Credit guarantee,Correct construction elevator site inspection First of all, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, the lift also has a lot of safety equipment.The motor winding is short-circuited. When a short-circuit fault occurs in the motor winding, the short-circuit current is much larger than the normal operating current, which increases the copper loss of the winding, causing the winding to overheat and even burn out.In the construction elevator, the switch box also has leakage protection equipment. Its wires and cables are well insulated without leakage, and the metal threaded is not rusted, and its damage is close to zero. His steel wire rope should comply with the corresponding configuration requirements, and there is no problem of broken strands and diameter reduction. Of course, the number of broken wires should not exceed the corresponding standard. His pulley movement is very flexible.

Hydraulic system: mainly oil cylinders, high-strength chrome-plated rods, Japanese NOK seals, self-made external integrated pump stations, oil pipelines, gear pumps, solenoid valves, etc. The Japanese NOK seal used in the oil cylinder has good wear resistance, which ensures that the oil cylinder series will not leak oil for a long time. The gear pump pumps the oil in the oil tank into the oil circuit and enters the oil cylinder, thereby driving the top of the rod and raising the equipment; The valve is used to adjust the oil output, the ascending and descending speed, and contains an emergency descending device to ensure that the guide rail hydraulic lifting platform can descend safely in case of an emergency.Convenient and efficient,Today, the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.: High-pressure water abrasive derusting. Using the impact of high-pressure water jets and abrasives to polish and remove rust on the screw elevator, the advantage is that the damage to the material is small, but the water has certain damage to the electronic equipment, and it is suitable for the detachable type of screw elevator.Anti-corrosion measures for the body of aerial work vehicles Pay attention to small scratches. The paint surface of aerial work vehicles is often corroded. In addition to common collisions, scratches, small rocks on the driving tires, there may also be a peeling paint spot, and a small rust will appear after a long time. Because most of these scars are small, they are easy to ignore. Therefore, check regularly, the engine compartment cover and its surroundings, and once found, go to a professional beauty shop for processing.Louisville,Conscientiously write the special construction plan for installation and construction, and make safety technical disclosures to the installers.How to effectively prevent electric shock by using a hydraulic lifting platform It is very common to add a leakage protector, and the cost is not high. It is both affordable and safe, and can effectively prevent electric shock.Today, the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.

Today, the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.The common types of lifts are simply introduced here for you. I hope you can learn more about this product. At present, this product can be said to be sold well in China, because many places need to use this product. Products that can be lifted and moved flexibly at the same time. Now companies that specialize in the production of this product combine a large-scale external publicity on the Internet. Friends in need can directly find the corresponding company on the Internet, and then simply learn about the models of these products and Information on performance and price can be purchased directly through the Internet.Messina,In the daily maintenance of the elevator, if the motor is overheated, stop immediately and continue to run after removing the fault. The motor bearing should be lubricated with good quality.When the freight elevator breaks down,MessinaLifting cargo elevator, professionals should be invited to repair it, and the freight elevator cannot be altered without authorization.Consolacion-del-Sur,Guide rail lift (also known as freight elevator) is a non-scissor hydraulic lifting platform, which is mainly used in industrial plants, restaurants, restaurants, warehouses,MessinaElevating cargo elevator 1-4 floors, docks, workshops and other places that need to move goods vertically between high-rise buildings above the second floor. The low height is especially suitable for sites where the site is not suitable for digging pits. What problems do we need to pay attention to in these places where elevators are used?Check the front page of the oil pipe to check whether the skin of the oil pipe of the hydraulic lifting platform is damaged or cracked, and if so, replace it immediately; secondly, check whether there is any sign of looseness at the connection between the oil pipe and the oil pipe,MessinaGood comments on cargo elevators, and if so, tighten it immediately to avoid lifting on the hydraulic lifting platform There is an oil spill in the process, which leads to accidents; what items need to be checked before using the hydraulic lifting platform? Cut off the power first to avoid tragedies such as electric leakage and electric shock)Regular maintenance Regularly check whether the circuit system of the hydraulic lifting platform is loose, and check whether the wires and cables are aging and damaged, which may cause leakage of the line. If there is it should be repaired in time to avoid electric shock.

The hydraulic lifting platform is mainly the pressure transmission of hydraulic oil to realize the lifting function. Its scissor mechanical structure makes the lift stable, and the wide operating platform and high carrying capacity make the high-altitude operation wide and suitable for many people work at the same time. It makes high-altitude operations efficient and secure.Precautions for daily maintenance of hydraulic lifts Check all hydraulic pipes and joints of hydraulic lifts. The pipes must not be damaged, the joints must not be loose, and all joints must be tightened.It is best not to cover the aerial work vehicle and park the vehicle outside. If it is windy and rainy, the clothing will repeatedly slap the car paint, especially if the car blows sand on the clothes, it will draw many fine scratches on it. Because it will turn black over time. In addition when the wind does not directly spray powder or clean the sand on the mechanism, and prevent the sand particles on the paint surface from being scratched by the vacuum cleaner.Quality recommendation,The use of the hydraulic lifting platform The user can choose the power mode and configuration according to his own scope of use: the power system includes: DC power supply, single-phase or three-phase power supply, and diesel engine.Naturally connect the motor to the lift. When connecting, it will cause the motor shaft to break or the elevator gear to wear.Hydraulic pump station: special pump station for domestic lifting platform, protection device outside the pump station imported from Italy: organ m type, mesh type, iron plate seal type.

The daily maintenance of the hydraulic lifting platform in normal use is essential, but even if there is normal maintenance on the equipment, any possible problem cannot be ignored, so in order to ensure that the process of using the hydraulic lifting platform for each operation What aspects do we need to check before operation? Today, the editor will give you a popular science.Discount,The elevator is a kind of elevator equipment composed of traveling mechanism, hydraulic mechanism, electric mechanism and supporting mechanism. The hydraulic oil is under a certain pressure formed by the vane pump, and enters the lower end of the hydraulic cylinder through the oil filter, explosion-proof electromagnetic reversing valve, throttle valve, hydraulic control check valve, and balance valve, so that the upward movement of the hydraulic cylinder can lift heavy objects , The oil returned from the upper end of the hydraulic cylinder returns to the oil tank through the explosion-proof electromagnetic reversing valve, and the rated pressure relief valve is adjusted, and the pressure gauge reads the pressure gauge.In our daily life today, the application of hydraulic lifts is becoming more and more extensive, and it is deeply loved by customers. As a lifting tool the maintenance of lifts must not be sloppy. The following editor will introduce the daily maintenance of hydraulic lifts .Test the freight elevator every day to see if the freight elevator can operate normally.Messina,Unscrew the screw on the dust-proof hole outside the flange of the elevator, adjust the PCS system ring to align the side hole with the dust-proof hole and tighten the inner hexagon. After that, remove the motor shaft key.Nowadays, old brand, price advantage, quality guaranteed!

Safety performance: The lifting structure is made of high-strength manganese steel rectangular tube, and the scissor-type mechanical mechanism is easy to maintain, with strong stability and high carrying capacity. The maximum lifting height is about meters, and the maximum load is about tons. .Secondly, there must be no dirt on the friction surface. If there is dirt, it needs to be washed off with gasoline or thinner; the gear box, gearbox, external gear and other parts of the equipment and the hydraulic oil must be in accordance with the requirements in the table; Correctly maintain the hydraulic guide rail lift. Regularly check whether the wire ropes in each part are broken or loose. If this phenomenon is found, replace them in time. If there is any looseness, it should be tightened in time. The connecting bolts of the equipment should be checked for tightness when the body is under pressure. All connecting shafts should be equipped with cotter pins; check whether each mechanism is operating normally, whether there is noise or failure , to eliminate all faults in a timely manner; when installing, dismantling and adjusting the slewing mechanism of the equipment, it is necessary to pay attention to the parallelism between the reducer and the center line of the gear, and the appropriate meshing gap; conduct a comprehensive inspection of the equipment regularly, whether the wires and cables are If there is damage, whether the motor is overheated, each box, distribution box and brushes must be kept clean, and the travel switch points of each safety device must be safe and reliable.valence,Therefore, before heavy platform operation, including: operation content and requirements; safety matters and dangerous points; division of labor and scope of responsibility. The operator should not only check the condition of the vehicle and the operator, but also check the terrain environment, whether the flight and landing meet the needs of safety skills or the pre-established operation plan. If there is income and expenditure, corresponding measures should be formulated before starting to operate.It is strictly forbidden to switch the electric control switch with wet hands. Many people tend to ignore this detail. Although the safety voltage of the hydraulic lifting platform is below V, if you touch the power supply with your hands, it may cause lifting failure in light cases, or electric shock accidents in severe cases.Asbe Teferi,Use Hydraulic lifts are widely used in various industrial enterprises and production lines such as automobiles, containers, mold manufacturing, wood processing, etc., to meet the lifting needs of different operating heights, and can be equipped with various table forms (such as balls, rollers, Turntable steering, telescopic) tilting, with various methods (separate, linkage, explosion-proof), with the characteristics of stable and accurate lifting frequent starting, etc. large load capacity, effectively solving the difficulties of various lifting operations in industrial enterprises, so that Production operations freely. The professional elevator factory has advanced technology, strict testing, and more discounts are in progress, welcome to consult.What is the new price of fixed lifts? Fixed lifts are currently very popular in the market. Due to different manufacturers, different materials, different rated loads, and different brand awareness, the prices are also different. The current price of fixed lifts produced in the domestic market: rated load - tons, height of meters,valenceThree ton cargo elevator, table size mm *mm, the price is about - yuan; the rated load is - tons, the height is meters, the table size is mm*mm, the price is about yuan. Rated load, lift height, table size of each fixed liftDifferent. (Specific bearing capacity and rising height can be customized according to user requirements)This kind of fixed lifting equipment can also be used in the warehouse. For example a certain floor in the warehouse needs to be lifted to send goods or personnel into the designated warehouse.

The last thing to note is that, compared with the lifting platforms in some places, protective fences are generally added on the platforms. Since the lifting platforms are special equipment,valenceCar lift cargo elevator, the National Quality Inspection Bureau is very strict on this piece of inspection. All must be dismantled, so when the personnel ask you if you want to add a guardrail, don't blindly refuse, and consider whether it is necessary according to the site of use. In addition, you must have the 'People's Republic of Special Equipment Manufacturing License' and the 'People's Republic of Special Equipment Installation,valenceElevating cargo elevators from first to second floors, Transformation and Maintenance License' to produce, install, and maintain. Therefore, you must ask whether the manufacturer has these two certificates.The elevator incidents that occurred in China in recent years in mobile elevator manufacturers are caused by three factors, namely, human error, which is purely caused by the lack of equipment-related operators. The second type is simple lifts such as hoists that have been eliminated in China and are not allowed to be used. It is aging equipment, more prone to accidents. The third is that the quality of production is not good enough, the loading and unloading of materials, the adjustment of the working height during the assembly of the workpiece, the feeding of the installed machine at a high place the lifting of parts during the assembly of large equipment, and the storage and unloading place and Forklifts and other handling vehicles are used for fast loading and unloading of goods, car lifting, fixed three-dimensional parking and other places.Administration,Are the water cooling and air cooling of the hydraulic station the same?Frequently check the humidity of the aerial work vehicle that is prone to water accumulation. It is inevitable that the aerial work vehicle is driving in rainy and snowy weather, or on muddy roads. The bottom and some gaps and indoor floors are easy to accumulate sludge. If the owner does not clean it in time, this will hide the moisture. Therefore, the outer edge of the wheel hub, the door, the corner of the bottom of the trunk, the key hole and the wiper frame and other areas should be checked regularly, and the drainage holes in the door and various parts should be kept unblocked to ensure that the car seat covers, carpets and floors are protected from humidity. Rusty fittings.Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, the lift also has a lot of safety equipment.

The load of this series of products is divided into . to . tons, and can also be customized according to user requirements, with a load of up to tons.Design brand,The cleanliness of the hydraulic station is an important aspect of the elevator hydraulic station, so it should not be careless. Moreover, there are relevant rules and requirements, and you should refer to the specification manual, so that you can have a correct understanding and know how to achieve better cleanliness.The 'streamlined' open loose-leaf joint design of the hydraulic boarding bridge increases the welding area by more than times compared with the general tubular joint, which effectively prolongs the service life and simplifies maintenance.Avoid working in an environment. In the event of rain, snow and other weather the use of the hydraulic lifting platform should be stopped to prevent the occurrence of a short circuit, resulting in electric leakage and electric shock; non-professionals are strictly prohibited from disassembling electrical appliances such as hydraulic lifting platforms. In the event of an accident, you can’t disassemble without permission to eliminate the cause. You must report to the manufacturer for repair in time, inform the phenomenon of the accident, guarantees service. Guarantees quality. Your satisfaction is our pursuit! Welcome to inquire.valence,The boxes and distribution boxes of the hydraulic lift are always kept clean, and the dust on the electrical equipment is cleaned in time.Hydraulic pump station: special pump station for domestic lifting platform, protection device outside the pump station imported from Italy: organ m type, mesh type, iron plate seal type.Precautions for elevator installation Keep the access road of the external construction elevator smooth and have enough parking space for equipment. When it is necessary to use a steam crane for auxiliary installation, it should be fully considered whether the site environment meets the operating conditions of the steam crane.

After the goods are transported, clean up the debris on the platform.Avoid working in an environment. In the event of rain, snow and other weather, the use of the hydraulic lifting platform should be stopped to prevent the occurrence of a short circuit, resulting in electric leakage and electric shock; non-professionals are strictly prohibited from disassembling electrical appliances such as hydraulic lifting platforms. In the event of an accident, you can’t disassemble without permission to eliminate the cause. You must report to the manufacturer for repair in time, inform the phenomenon of the accident and the manufacturer will guide you to complete the inspection or send someone to repair it; do not disassemble the appliance without permission! Professional elevator factory guarantees quality, guarantees service. Guarantees quality. Your satisfaction is our pursuit! Welcome to inquire.Baja ,Check whether the self-locking device of the differential protector is normal before working at heights.Check the limit switch to see if all the limit switches are loose. If so, please tighten them. Pay special attention to the ultra-high protection stroke of the hydraulic lifting platform to avoid accidents caused by the equipment exceeding the high safety height; check the pins (ear pins and center pins) Check whether the nuts, nuts, screws, etc. are loose, if any, should be reinforced immediately; ensure that the hydraulic lifting platform rises and falls smoothly; outriggers (for high-altitude operating platform)Malangwa,Hydraulic system: mainly oil cylinders, high-strength chrome-plated rods, Japanese NOK seals, self-made external integrated pump stations, oil pipelines, gear pumps, solenoid valves, etc. The Japanese NOK seal used in the oil cylinder has good wear resistance, which ensures that the oil cylinder series will not leak oil for a long time. The gear pump pumps the oil in the oil tank into the oil circuit and enters the oil cylinder, the ascending and descending speed, and contains an emergency descending device to ensure that the guide rail hydraulic lifting platform can descend safely in case of an emergency.The load of this series of products is divided into . to . tons, and can also be customized according to user requirements, with a load of up to tons.Use Hydraulic lifts are widely used in various industrial enterprises and production lines such as automobiles, containers, mold manufacturing, wood processing, chemical filling, etc., to meet the lifting needs of different operating heights, and can be equipped with various table forms (such as balls, rollers, Turntable, steering, tilting telescopic), with various methods (separate, linkage, explosion-proof) with the characteristics of stable and accurate lifting, frequent starting, large load capacity, effectively solving the difficulties of various lifting operations in industrial enterprises, so that Production operations freely. The professional elevator factory has advanced technology strict testing, more affordable prices, and more discounts are in progress, welcome to consult.

The motor connection is wrong. When the delta connection motor is wrongly connected into a star shape, the motor still runs with full load, and the current flowing through the stator winding will exceed the rated current, and even cause the motor to stop by itself. If it overheats, it will burn out. When the star-connected motor is wrongly connected into a triangle, or the motor with several coil groups connected in series to form a branch circuit is connected in parallel with two branches, it will cause the winding and core to overheat, and in severe cases, and checked according to the bending fatigue strength of the tooth root. The bracket bracket is used to fix and support all the mechanical parts and some electrical components of the elevator box. It is mainly welded by side plates, connecting pipes and connecting pieces. You can choose any product, and the professional elevator factory has safe and secure transactions. At the same time, many craft holes are designed on the two side plates. Because the worm gear mechanism has the advantages of large transmission ratio, compact structure, small impact load, it also has the characteristics of reverse self-locking. It can ensure that the transmission mechanism can self-lock when the motor is powered off during the process of transporting patients, so the worm gear reducer is selected. The involute worm is used, the material is steel, and the helical surface is quenched to improve the transmission efficiency and increase the wear resistance. The material of the worm gear is polyoxymethylene. The plastic worm gear has the advantages of good processing economy, stable transmission, vibration absorption and noise reduction, light weight, wear resistance and self-improvement, which makes the design of the elevator more humanized.Whether it is used outdoors or indoors, some small problems will inevitably appear after a long period of time. At this time, what we should do is to maintain and maintain the elevator. How to follow the steps correctly It has become a difficult problem, and I will answer it with you.project, and the dust on the electrical equipment is cleaned in time.Precautions for using guide rail elevators Precautions for using guide rail elevators: It is strictly forbidden to overload, transport flammable and explosive products and other products.Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, the lift also has a lot of safety equipment.

The use of the hydraulic lifting platform The user can choose the power mode and configuration according to his own scope of use: the power system includes: DC power supply, single-phase or three-phase power supply and diesel engine.target,The safety device of the guide rail hydraulic lifting platform The mechanical part of the guide rail hydraulic lifting platform mainly includes the hydraulic system and the mechanical device.Now we have more and more demands for elevators,Baja Two story cargo elevator, so the editor will introduce the maintenance work of guide rail elevators. When we usually use the guide rail type elevator, we should often carry out inspection, maintenance and maintenance, which will not only prolong the service life of the guide rail type elevator, but also make it work more powerfully! For example, there should be enough oil in the transmission part,Baja Warehouse elevator, and the wearing parts must be checked,Baja Guide rail type cargo elevator cargo elevator, repaired or replaced frequently. For mechanical bolts, especially parts that vibrate frequently, such as slewing rings and lifting arm connecting bolts check whether they are loose. Loose must be tightened or replaced. The steps of maintenance are introduced below: important maintenance work of the rail-type elevator. Regularly check the tire pressure of the rail-type elevator and whether the condition of the bearing is normal; regularly check whether the structure of the bracket and the panel is in good condition. Grease is added once a month; the wearing parts must be checked, repaired or replaced frequently, and the parts that vibrate frequently, such as bolts and slewing bearings, should be checked for looseness. If they are loose, they must be tightened or replaced immediately.Many people think that the strength of the elevator itself is relatively high when using the elevator, so they did not strictly follow the installation method in the manual during the installation process, but they do not know that this will cause increased wear and tear of the parts and inflexible operation, and pay attention to the work The installation precautions corresponding to the environment should not be ignored. Correct installation, use and maintenance of elevators are an important part of ensuring the normal operation of mechanical equipment. Therefore, when you install the elevator, please be sure to strictly follow the installation and use related matters below, and assemble and use it carefully.Baja ,It is best not to cover the aerial work vehicle and park the vehicle outside. If it is windy and rainy, the clothing will repeatedly slap the car paint, especially if the car blows sand on the clothes, it will draw many fine scratches on it. Because it will turn black over time. In addition, when the wind does not directly spray powder or clean the sand on the mechanism, but it should be washed with water, and prevent the sand particles on the paint surface from being scratched by the vacuum cleaner.Safety performance: The lifting structure is made of high-strength manganese steel rectangular tube, and the scissor-type mechanical mechanism is easy to maintain, with strong stability and high carrying capacity. The maximum lifting height is about meters, and the maximum load is about tons. .Pay attention to check whether there are any broken wires and loose strands in the wire ropes of each part. If it exceeds the relevant regulations

It is strictly forbidden to switch the electric control switch with wet hands. Many people tend to ignore this detail. Although the safety voltage of the hydraulic lifting platform is below V, if you touch the power supply with your hands, it may cause lifting failure in light cases, or electric shock accidents in severe cases.The last thing to note is that, compared with the lifting platforms in some places, protective fences are generally added on the platforms. Since the lifting platforms are special equipment, the National Quality Inspection Bureau is very strict on this piece of inspection. All must be dismantled, so when the personnel ask you if you want to add a guardrail, don't blindly refuse, you must have the 'People's Republic of Special Equipment Manufacturing License' and the 'People's Republic of Special Equipment Installation, Transformation and Maintenance License' to produce, install and maintain. Therefore, you must ask whether the manufacturer has these two certificates.Spiegel Kenneth,Looseness occurs: The newly processed and assembled parts of mobile lifts and other aerial work platform equipment have a tendency to geometric shape and matching size. , Coupled with excessive wear and other reasons, it is easy to loosen the originally fastened parts of aerial work platform equipment such as mobile lifts.The cleanliness of the hydraulic station is an important aspect of the elevator hydraulic station, so it should not be careless. Moreover, there are relevant rules and requirements, and you should refer to the specification manual, so that you can have a correct understanding and know how to achieve better cleanliness.Kota,Check the front page of the oil pipe to check whether the skin of the oil pipe of the hydraulic lifting platform is damaged or cracked, and if so, replace it immediately; secondly, check whether there is any sign of looseness at the connection between the oil pipe and the oil pipe, and if so, tighten it immediately to avoid lifting on the hydraulic lifting platform There is an oil spill in the process, which leads to accidents; what items need to be checked before using the hydraulic lifting platform? Cut off the power first to avoid tragedies such as electric leakage and electric shock)Always check the connections of the various parts of the hydraulic lift, and tighten them if they are loose. The tightness of the connecting bolts of the body should be checked when the body is under pressure.Today, the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.

Nowadays, small and medium-sized enterprises are holding products with the idea of ​​good quality and favorable price.The one-way valve is damaged. The one-way valve is to prevent the oil from returning. If there is a problem, there will be some backflow, so it can be replaced with a new one at this time.The surface of the brushes of each part should be kept clean, and the pressure of the brushes should be adjusted so that the area is not less than %. Professional elevator factory, large quantity favorably, high quality and low price. Fire-resistant-waterproof-high temperature resistant, durable,Safety performance: The lifting structure is made of high-strength manganese steel rectangular tube, and the scissor-type mechanical mechanism is easy to maintain with strong stability and high carrying capacity. The maximum lifting height is about meters, and the maximum load is about tons. .If the motor of the hydraulic lift is overheated stop the machine in time and continue running after troubleshooting. The motor bearings must be in good condition.The design of the hydraulic lifting platform is unreasonable. When the designer designs the cylinder barrel and rod, if there is a problem with the design size and angle, then there will definitely be problems in the later stage. Therefore, it is necessary to confirm the technical strength of the manufacturer when working on a hydraulic lifting platform; what is the problem with the sound of the oil cylinder of the hydraulic lifting platform? Design drawings to make the angle of the oil cylinder is slightly deviated, it will cause the friction between the cylinder barrel and the rod, which will cause the sound; the seal quality of the hydraulic lifting platform is different, and the use of different seals will also affect the sound of the oil cylinder, and the seal with excellent material The continuous friction between the parts and the cylinder wall will cause the sound to be very loud, and long-term wear and tear may scratch the oil cylinder and cause oil leakage, so when the hydraulic lifting platform is used, pay attention to ask the manufacturer what brand and material the seal is used; In some cases of mechanical running-in it is not ruled out that the above three situations are normal, and there will still be noises. If there is no problem after investigation, then don’t worry. It’s just a running-in problem between mechanical parts. It will disappear naturally.

Naturally connect the motor to the lift. When connecting, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, and that the outer flanges of the two are parallel. If the concentricity is inconsistent, it will cause the motor shaft to break or the elevator gear to wear.Range,Outriggers: mechanical outriggers, hydraulic outriggers, ordinary hand-operated outriggers, pull-out outriggers.Avoid,Spiegel KennethOutdoor lifting cargo elevator, especially during storage. Store in a cool, dry place, snow and other weather, the use of the hydraulic lifting platform should be stopped to prevent the occurrence of a short circuit, resulting in electric leakage and electric shock; non-professionals are strictly prohibited from disassembling electrical appliances such as hydraulic lifting platforms. In the event of an accident, you can’t disassemble without permission to eliminate the cause. You must report to the manufacturer for repair in time, inform the phenomenon of the accident, and the manufacturer will guide you to complete the inspection or send someone to repair it; do not disassemble the appliance without permission! Professional elevator factory guarantees quality, guarantees service. Guarantees quality. Your satisfaction is our pursuit! Welcome to inquire.Spiegel Kenneth,Nowadays, small and medium-sized enterprises are holding products with the idea of ​​good quality and favorable price.The parts such as reduction box, external gear and hydraulic oil are all in accordance with the requirements in the table.Guide rail lift (also known as freight elevator) is a non-scissor hydraulic lifting platform, which is mainly used in industrial plants, restaurants, restaurants,Spiegel KennethFloor to floor cargo elevator, warehouses, docks, workshops and other places that need to move goods vertically between high-rise buildings above the second floor. The low height is especially suitable for sites where the site is not suitable for digging pits. What problems do we need to pay attention to in these places where elevators are used?

Pay attention to check whether there are any broken wires and loose strands in the wire ropes of each part. If it exceeds the relevant regulations, it must be replaced immediately. The maintenance of the wire rope should be strictly in accordance with regulations.The motor winding is short-circuited. When a short-circuit fault occurs in the motor winding, the short-circuit current is much larger than the normal operating current, which increases the copper loss of the winding, causing the winding to overheat and even burn out.Seventeen green ancient city,Safety ropes for mobile lifts. Personnel working at heights are always required to hang their safety belts on the safety ropes during mobile operations.Nowadays, small and medium-sized enterprises are holding products with the idea of ​​good quality and favorable price.Bekes,If the motor of the hydraulic lift is overheated stop the machine in time and continue running after troubleshooting. The motor bearings must be in good condition.The price is guaranteed, the service is guaranteed, and it is a large-scale logistics and storage equipment service company directly operated by the manufacturer. Since the fixed lift is a mechanical device, the quality and performance of the product must be good. Do not accept the products of some manufacturers whose quality is not up to standard, if there is a problem with the design size and angle then there will definitely be problems in the later stage. Therefore, the angle of the oil cylinder is slightly deviated, it will cause the friction between the cylinder barrel and the rod, which will cause the sound; the seal quality of the hydraulic lifting platform is different, and the use of different seals will also affect the sound of the oil cylinder, and the seal with excellent material The continuous friction between the parts and the cylinder wall will cause the sound to be very loud,Seventeen green ancient cityFixed lifting cargo elevator, and long-term wear and tear may scratch the oil cylinder and cause oil leakage, so when the hydraulic lifting platform is used, pay attention to ask the manufacturer what brand and material the seal is used; In some cases of mechanical running-in, it is not ruled out that the above three situations are normal, and there will still be noises. If there is no problem after investigation, then don’t worry. It’s just a running-in problem between mechanical parts. It will disappear naturally.

Secondly, there must be no dirt on the friction surface. If there is dirt, it needs to be washed off with gasoline or thinner; the gear box, gearbox, replace them in time. If there is any looseness it should be tightened in time. The connecting bolts of the equipment should be checked for tightness when the body is under pressure. All connecting shafts should be equipped with cotter pins; check whether each mechanism is operating normally, whether there is noise or failure , to eliminate all faults in a timely manner; when installing,Seventeen green ancient cityWarehouse elevator, dismantling and adjusting the slewing mechanism of the equipment, it is necessary to pay attention to the parallelism between the reducer and the center line of the gear, whether the wires and cables are If there is damage, whether the motor is overheated, replace it in time and continue to run after troubleshooting; ensure that the bearings of the motor, each box distribution box and brushes must be kept clean, and the travel switch points of each safety device must be safe and reliable.The daily maintenance of guide rail lifting equipment should pay attention to regular inspection and maintenance, eliminate hidden dangers, and eliminate faults. Doing this is good for improving work efficiency,Seventeen green ancient cityHydraulic lifting cargo elevator, prolonging the service life of equipment and ensuring the safety performance of the elevator.What are the maintenance rules for hydraulic lift machinery? The brakes of each mechanism should be checked frequently and the gap between the brake shoe and the brake wheel should be adjusted to ensure flexibility and reliability. There should be no dirt on the friction surface, and if there is dirt, it must be washed off with gasoline or thinner.For more, please check,When installing, dismantling and adjusting the slewing mechanism, care should be taken to ensure that the centerline of the slewing mechanism reducer is parallel to the centerline of the gear, the meshing surface is not less than %, and the meshing clearance is suitable.Always check the connections of the various parts of the hydraulic lift, and tighten them if they are loose. The tightness of the connecting bolts of the body should be checked when the body is under pressure.Use Hydraulic lifts are widely used in various industrial enterprises and production lines such as automobiles, containers, mold manufacturing, wood processing, chemical filling, etc., to meet the lifting needs of different operating heights, and can be equipped with various table forms (such as balls, rollers, Turntable, steering, tilting, telescopic), with various methods (separate, explosion-proof), with the characteristics of stable and accurate lifting, frequent starting, large load capacity, etc., effectively solving the difficulties of various lifting operations in industrial enterprises, so that Production operations freely. The professional elevator factory has advanced technology, strict testing, more affordable prices, and more discounts are in progress, welcome to consult.

The wrong connection of the motor of the elevator When a coil, it will cause a serious imbalance in the three-phase current and cause the winding to overheat.Professional is king,It is strictly forbidden for personnel to take the freight elevator to go up and down floors and climb.Novice operation: Since novices do not know much about mobile lifts and other aerial work platforms, or do not understand the operation method, they are prone to misoperation and cause equipment failure. Operators in this area need to study patiently and pass the training before they can operate and use.If the motor of the hydraulic lift is overheated stop the machine in time and continue running after troubleshooting. The motor bearings must be in good condition.Seventeen green ancient city,The price is guaranteed, the service is guaranteed, and it is a large-scale logistics and storage equipment service company directly operated by the manufacturer. Since the fixed lift is a mechanical device, the quality and performance of the product must be good. Do not accept the products of some manufacturers whose quality is not up to standard, so as to avoid some safety hazards in use.The hydraulic lifting platform is mainly the pressure transmission of hydraulic oil to realize the lifting function. Its scissor mechanical structure makes the lift stable, and the wide operating platform and high carrying capacity make the high-altitude operation wide and suitable for many people work at the same time. It makes high-altitude operations efficient and secure.The motor connection is wrong. When the delta connection motor is wrongly connected into a star shape, the motor still runs with full load, and the current flowing through the stator winding will exceed the rated current, and even cause the motor to stop by itself. If it overheats, it will burn out. When the star-connected motor is wrongly connected into a triangle, or the motor with several coil groups connected in series to form a branch circuit is connected in parallel with two branches, it will cause the winding and core to overheat, and in severe cases, the winding will be burned.

Test the freight elevator every day to see if the freight elevator can operate normally.It is best not to cover the aerial work vehicle and park the vehicle outside. If it is windy and rainy, the clothing will repeatedly slap the car paint, especially if the car blows sand on the clothes, it will draw many fine scratches on it. Because it will turn black over time. In addition when the wind does not directly spray powder or clean the sand on the mechanism, but it should be washed with water, and prevent the sand particles on the paint surface from being scratched by the vacuum cleaner.Shijiazhuang, if the motor is overheated, stop immediately and continue to run after removing the fault. The motor bearing should be lubricated with good quality.Unscrew the screw on the dust-proof hole outside the flange of the elevator adjust the PCS system ring to align the side hole with the dust-proof hole, and tighten the inner hexagon. After that, remove the motor shaft key.Petropolis,In the construction elevator, the switch box also has leakage protection equipment. Its wires and cables are well insulated, without leakage, and the metal threaded is not rusted, and its damage is close to zero. His steel wire rope should comply with the corresponding configuration requirements, and there is no problem of broken strands and diameter reduction. Of course, the number of broken wires should not exceed the corresponding standard. His pulley movement is very flexible.The design of the hydraulic lifting platform is unreasonable. When the designer designs the cylinder barrel and rod, if there is a problem with the design size and angle, then there will definitely be problems in the later stage. Therefore, it is necessary to confirm the technical strength of the manufacturer when working on a hydraulic lifting platform; what is the problem with the sound of the oil cylinder of the hydraulic lifting platform? Design drawings to make, the angle of the oil cylinder is slightly deviated, it will cause the friction between the cylinder barrel and the rod, which will cause the sound; the seal quality of the hydraulic lifting platform is different, and the use of different seals will also affect the sound of the oil cylinder, and the seal with excellent material The continuous friction between the parts and the cylinder wall will cause the sound to be very loud, and long-term wear and tear may scratch the oil cylinder and cause oil leakage, so when the hydraulic lifting platform is used, pay attention to ask the manufacturer what brand and material the seal is used; In some cases of mechanical running-in, it is not ruled out that the above three situations are normal, and there will still be noises. If there is no problem after investigation, then don’t worry. It’s just a running-in problem between mechanical parts. It will disappear naturally.The use of elevators is not to maintain and overhaul after the equipment fails. It is necessary to maintain the equipment according to the correct maintenance and overhaul, and start with the preparation work to prevent all possible failures and accidents. I hope that the editor can summarize the knowledge points today. Help everyone.

What is the new price of a fixed lift? Professionally improve the quality assurance of the freight elevator factory. The preferential activities are in progress, and new and old customers are welcome to come to consult.Make sure to add butter twice a month to the general transmission position where the grease fitting is located. For the parts that cannot be filled with butter, be sure to dredge the oil circuit or replace the grease fitting until the butter can be added, otherwise it is forbidden to use the equipment.The contact opening and closing of the travel switch of each safety device must be reliable and the contact arc crater should be polished in time.Safety and health,Walking: assisted self-propelled, self-driving, and car modified.Regular maintenance Regularly check whether the circuit system of the hydraulic lifting platform is loose, and check whether the wires and cables are aging and damaged, which may cause leakage of the line. If there is, it should be repaired in time to avoid electric shock.As for the guide rail elevator installed outdoors, it is often exposed to rain and sunlight, for example, it can be divided into fixed lifting devices and vehicle-mounted lifting devices according to the form of movement. The so-called fixed lifting means that it is generally installed in one place and fixed, and then the lifting operation can be carried out. This type of lifting equipment is generally used more on the assembly line. Some large-scale production lines need to move the material when loading materials. Lifting to a certain position, and then putting it into the production line for production, a special lifting device is required to be fixed at a certain position of the production line.assets,It is best not to cover the aerial work vehicle and park the vehicle outside. If it is windy and rainy, the clothing will repeatedly slap the car paint, especially if the car blows sand on the clothes, it will draw many fine scratches on it. Because it will turn black over time. In addition, when the wind does not directly spray powder or clean the sand on the mechanism, but it should be washed with water, and prevent the sand particles on the paint surface from being scratched by the vacuum cleaner.It is necessary to bandage and replace the damaged part in time. The elevator is a kind of hydraulic elevator, also known as the guide rail hydraulic elevator, which is suitable for the transportation of goods higher than buildings, Lipusheng Machinery will introduce to you the daily maintenance of the elevator.Goods should be stacked on the platform and not tilted. When the freight elevator goes up and down beyond the range of the platform, no one should stand around to watch.Shijiazhuang,In addition to the fixed mode, the elevator also has a vehicle-mounted mobile type. As the name implies, it combines the lifting equipment with the vehicle-mounted system. Such a lifting equipment is very flexible to move, and of course it is more useful. For example There is this kind of lifting equipment in the airport, and it is also possible to install this kind of equipment in stations or stadiums. Since it can be moved,Shijiazhuang3 ton fixed lifting cargo elevator, the scope of operation is not limited to a certain place and it can be used wherever lifting operations are required. It can be used. For example, when installing outdoor advertisements, the height of some advertisements is relatively high. At this time, mobile lifting equipment can be used to send billboards or staff to the designated height to work. This kind of equipment can also be divided into two types according to the driving mode: hydraulic lifting and electric lifting. The so-called hydraulic lifting is driven by hydraulic oil to reach a specified height. The electric mode is driven by a motor or geared to lift to A certain height, but at present, hydraulic lifting platforms are more widely used.What is the new price of a fixed lift? Professionally improve the quality assurance of the freight elevator factory. The preferential activities are in progress, and new and old customers are welcome to come to consult.The elevator is a kind of elevator equipment composed of traveling mechanism, hydraulic mechanism, and enters the lower end of the hydraulic cylinder through the oil filter explosion-proof electromagnetic reversing valve, throttle valve, hydraulic control check valve, and balance valve,ShijiazhuangCar lift cargo elevator, so that the upward movement of the hydraulic cylinder can lift heavy objects , The oil returned from the upper end of the hydraulic cylinder returns to the oil tank through the explosion-proof electromagnetic reversing valve, and the rated pressure relief valve is adjusted, and the pressure gauge reads the pressure gauge.

Outriggers: mechanical outriggers, hydraulic outriggers, ordinary hand-operated outriggers, pull-out outriggers.Mechanisms: Mechanisms such as tabletops, track grooves, chains,Mobile lift fault analysis mobileAnalysis of the mobile lift’s poor lift or weak lifting force: the pressure adjustment of the relief valve does not meet the requirements: adjust the pressure to the required value; the internal leakage of the oil cylinder: check or replace the oil cylinder assembly; the reversing valve is locked or internally leaked: check or exchange the valve assembly ;The oil level is too low,BerlinOne ton cargo elevator, and the oil inlet filter is blocked: add enough oil and clean the oil filter. Fuel pump defective: check or replace pump.The water cooling of the hydraulic station is generally tube-type water cooling, and its type selection is based on the heat load to calculate the heat exchange area, while its air-cooled elevator is carried out by using an air cooler, and it is The heat transfer capacity is calculated according to the heat load, and then the type selection calculation is carried out under the condition that the flow rate can be satisfied. Therefore, these two kinds of cooling are not the same, and there is a big difference. Long-term promotion of freight elevator factories and other, Long-term cooperation, mutual benefit and win-win. If you choose the wrong supplier, you will be overwhelmed with all kinds of after-sales troubles in the later stage. Recently, I have seen many netizens report the problem of very loud oil cylinders. Today, the editor will simply popularize the knowledge for everyone.Aler Province,Features of hydraulic lifts: According to the working mode, hydraulic lifting platform products are divided into crank arm hydraulic lifting machines, scissor hydraulic lifting machines, mast type hydraulic lifts, and straight arm hydraulic lifting machines. The hydraulic lift is a replacement product of the folding arm lift (lifting platform) and the scissor lift (lifting platform). It can be widely used in stations, docks, airports, hotels, post and telecommunications, municipal gardens, garages cleaning companies, public building facade decoration, decoration or installation and maintenance of power systems, etc. The lift has the advantages of light weight, self-propelled electric start, self-supporting legs, simple operation, large working area, especially the ability to cross obstacles for high-altitude operations and the like.As for the guide rail elevator installed outdoors, it is often exposed to rain and sunlight so special attention should be paid to regular maintenance and inspection to avoid accidents.When installing, dismantling and adjusting the slewing mechanism, care should be taken to ensure that the centerline of the slewing mechanism reducer is parallel to the centerline of the gear, the meshing surface is not less than %, and the meshing clearance is suitable.

The boxes and distribution boxes of the hydraulic lift are always kept clean, and the dust on the electrical equipment is cleaned in time.Beginners operating mobile lifts should pay attention to which equipment wears quickly: due to the processing and installation of mobile lifts and other aerial work platform equipment components, the surface of the equipment is rough, the area is small, and the load is uneven causing equipment wear. During the operation of aerial work platform equipment such as mobile lifts, the concave and convex parts on the surface of the parts fit and rub against each other, and the metal debris and the equipment undergo secondary friction, which will accelerate the wear of the surface of the equipment parts. Therefore, during the break-in period of mobile lifts and other aerial work platform equipment, it is easy to cause wear of parts and components, and the wear speed is fast.The safety device and application of the guide rail hydraulic lifting platform The use of the guide rail hydraulic lifting platform The guide rail hydraulic lifting platform is a non-scissor hydraulic lifting freight elevator. It is used for goods between different floors of industrial plants, restaurants, restaurants, etc. The low height can be made to -mm. The advantage is that it can be placed directly on the ground without digging pits, reducing engineering construction costs, and there is no need to set up hanging points on the top, which is safe. Reliable; the hydraulic lifting platform adopts hydraulic transmission mode, and can be non-calibrated according to customer needsSeveral types: Motor winding open circuit. When one of the motor windings is disconnected, or one of the parallel branches is disconnected, the three-phase current will be unbalanced and the motor will overheat.Honesty is the foundation,When installing, dismantling and adjusting the slewing mechanism, care should be taken to ensure that the centerline of the slewing mechanism reducer is parallel to the centerline of the gear, the meshing surface is not less than %, and the meshing clearance is suitable.Before using the aerial work platform, it is necessary to confirm whether the outriggers are well supported, and then proceed with the operation; the rollers and slideways confirm whether the roller slideways of the hydraulic lifting platform are dry, and if there is When drying the site, an appropriate amount of butter should be added to ensure the smoothness during operation and to avoid head-to-head wear between mechanical parts.Anti-corrosion measures for the body of aerial work vehicles Pay attention to small scratches. The paint surface of aerial work vehicles is often corroded. In addition to common collisions, scratches, small rocks on the driving tires, there may also be a peeling paint spot, and a small rust will appear after a long time. Because most of these scars are small, they are easy to ignore. Therefore, check regularly, the engine compartment cover and its surroundings, and once found, some small problems will inevitably appear after a long period of time. At this time, what we should do is to maintain and maintain the elevator. How to follow the steps correctly It has become a difficult problem, and I will answer it with you.Safety and health,The design of the hydraulic lifting platform is unreasonable. When the designer designs the cylinder barrel and rod, if there is a problem with the design size and angle, it is necessary to confirm the technical strength of the manufacturer when working on a hydraulic lifting platform; what is the problem with the sound of the oil cylinder of the hydraulic lifting platform? Design drawings to make, the angle of the oil cylinder is slightly deviated, it will cause the friction between the cylinder barrel and the rod,Berlin1 ton lifting cargo elevator, which will cause the sound; the seal quality of the hydraulic lifting platform is different, and the use of different seals will also affect the sound of the oil cylinder, and the seal with excellent material The continuous friction between the parts and the cylinder wall will cause the sound to be very loud, and long-term wear and tear may scratch the oil cylinder and cause oil leakage, so when the hydraulic lifting platform is used, pay attention to ask the manufacturer what brand and material the seal is used; In some cases of mechanical running-in it is not ruled out that the above three situations are normal, and there will still be noises. If there is no problem after investigation, then don’t worry. It’s just a running-in problem between mechanical parts. It will disappear naturally.After careful inspection, it was found that it was mainly caused by two reasons. One was the loss of hydraulic pressure,BerlinIndustrial cargo elevators, and the other was leakage of hydraulic valves or seals.The safety device of the guide rail hydraulic lifting platform The mechanical part of the guide rail hydraulic lifting platform mainly includes the hydraulic system and the mechanical device.Berlin,Many people think that the strength of the elevator itself is relatively high when using the elevator, so they did not strictly follow the installation method in the manual during the installation process, but they do not know that this will cause increased wear and tear of the parts and inflexible operation, and pay attention to the work The installation precautions corresponding to the environment should not be ignored. Correct installation, use and maintenance of elevators are an important part of ensuring the normal operation of mechanical equipment. Therefore when you install the elevator, please be sure to strictly follow the installation and use related matters below, adjust the PCS system ring to align the side hole with the dust-proof hole, and tighten the inner hexagon. After that, remove the motor shaft key.Today, the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.

Before using the aerial work platform it is necessary to confirm whether the outriggers are well supported, refer to the level beads on the equipment to judge and debug, and then proceed with the operation; the rollers and slideways confirm whether the roller slideways of the hydraulic lifting platform are dry, and if there is When drying the site, an appropriate amount of butter should be added to ensure the smoothness during operation and to avoid head-to-head wear between mechanical parts.Features of hydraulic lifts: According to the working mode, hydraulic lifting platform products are divided into crank arm hydraulic lifting machines, scissor hydraulic lifting machines, mast type hydraulic lifts, docks, hotels, post and telecommunications,ArezzoGuide rail lifting cargo elevator,ArezzoProfessional cargo elevator, municipal gardens, garages, cleaning companies, public building facade decoration, decoration or installation and maintenance of power systems, etc. The lift has the advantages of light weight, self-propelled, electric start, self-supporting legs, simple operation, large working area, balls, turntables and other table tops can be configured arbitrarily, which can meet the requirements of different working conditions.The contact opening and closing of the travel switch of each safety device must be reliable, and the contact arc crater should be polished in time.Pirot,Check the limit switch to see if all the limit switches are loose. If so, please tighten them. Pay special attention to the ultra-high protection stroke of the hydraulic lifting platform to avoid accidents caused by the equipment exceeding the high safety height; check the pins (ear pins and center pins) Check whether the nuts, nuts screws, etc. are loose, if any, should be reinforced immediately; ensure that the hydraulic lifting platform rises and falls smoothly; outriggers (for high-altitude operating platform)Frequently check the humidity of the aerial work vehicle that is prone to water accumulation. It is inevitable that the aerial work vehicle is driving in rainy and snowy weather, or on muddy roads. The bottom and some gaps and indoor floors are easy to accumulate sludge. If the owner does not clean it in time this will hide the moisture. Therefore, the door, the corner of the bottom of the trunk, the key hole and the wiper frame and other areas should be checked regularly, and the drainage holes in the door and various parts should be kept unblocked to ensure that the car seat covers, carpets and floors are protected from humidity. Rusty fittings.Regarding the cleanliness of the hydraulic station, is there any relevant rule requirement?

Use Hydraulic lifts are widely used in various industrial enterprises and production lines such as automobiles, containers, mold manufacturing, wood processing, chemical filling, etc., to meet the lifting needs of different operating heights,Arezzo1 ton small lifting cargo elevator, and can be equipped with various table forms (such as balls, rollers, Turntable, steering, tilting telescopic), with various methods (separate, linkage, explosion-proof), with the characteristics of stable and accurate lifting, large load capacity, etc., effectively solving the difficulties of various lifting operations in industrial enterprises, so that Production operations freely. The professional elevator factory has advanced technology, strict testing, more affordable prices, and more discounts are in progress, welcome to consult.How to solve the leakage of the oil pipe when the elevator sinks? It may be that the seal is damaged, or the oil pipe has cracks, which leads to a drop in pressure and cannot support it to a large height.As for the guide rail elevator installed outdoors, it is often exposed to rain and sunlight, so special attention should be paid to regular maintenance and inspection to avoid accidents.Word of mouth recommendation,When installing, dismantling and adjusting the slewing mechanism, care should be taken to ensure that the centerline of the slewing mechanism reducer is parallel to the centerline of the gear, the meshing surface is not less than %, and the meshing clearance is suitable.What are the maintenance rules for hydraulic lift machinery? The brakes of each mechanism should be checked frequently and the gap between the brake shoe and the brake wheel should be adjusted to ensure flexibility and reliability. There should be no dirt on the friction surface, and if there is dirt it must be washed off with gasoline or thinner.When installing, dismantling and adjusting the slewing mechanism, care should be taken to ensure that the centerline of the slewing mechanism reducer is parallel to the centerline of the gear, the meshing surface is not less than %, and the meshing clearance is suitable.

Precautions for using guide rail elevators Precautions for using guide rail elevators: It is strictly forbidden to overload, transport flammable and explosive products and other products.Quality recommendation,Use Hydraulic lifts are widely used in various industrial enterprises and production lines such as automobiles, containers, mold manufacturing, wood processing, chemical filling, etc., to meet the lifting needs of different operating heights, and can be equipped with various table forms (such as balls, rollers, Turntable, steering, tilting, telescopic), with various methods (separate, explosion-proof), with the characteristics of stable and accurate lifting, frequent starting, large load capacity, etc., effectively solving the difficulties of various lifting operations in industrial enterprises, so that Production operations freely. The professional elevator factory has advanced technology, strict testing, more affordable prices, and more discounts are in progress, welcome to consult.Card lock; it is also a tool used to prevent equipment from falling suddenly due to accidents. It can be used in combination with card locks and explosion-proof valves.The contact opening and closing of the travel switch of each safety device must be reliable, and the contact arc crater should be polished in time.Arezzo,If the motor of the hydraulic lift is overheated, stop the machine in time and continue running after troubleshooting. The motor bearings must be in good condition.The last thing to note is that, compared with the lifting platforms in some places, protective fences are generally added on the platforms. Since the lifting platforms are special equipment the National Quality Inspection Bureau is very strict on this piece of inspection. All must be dismantled, so when the personnel ask you if you want to add a guardrail, don't blindly refuse, and consider whether it is necessary according to the site of use. In addition, you must have the 'People's Republic of Special Equipment Manufacturing License' and the 'People's Republic of Special Equipment Installation, Transformation and Maintenance License' to produce install, and maintain. Therefore, you must ask whether the manufacturer has these two certificates.It is strictly forbidden for personnel to take the freight elevator to go up and down floors and climb.

Precautions for elevator installation Keep the access road of the external construction elevator smooth and have enough parking space for equipment. When it is necessary to use a steam crane for auxiliary installation, it should be fully considered whether the site environment meets the operating conditions of the steam crane.Low cost: The cost is much lower than that of the scissor-type mobile lifting platform, so when purchasing a lifting platform, you must consider the scope of use of the lifting platform, the frequency of work, the load and other factors to choose a lifting platform that suits the work requirements .Minneapolis,How to maintain the elevator in winter? One reason is also the primary reason. Many workers in other industries do not know that the hydraulic oil of hydraulic elevators is also used in summer and winter. freeze. After entering the low temperature in winter, you must remember to replace the hydraulic oil containing antifreeze in winter, it can be realized. At the same time, paying attention to driving habits can ensure that the aerial work vehicle does not rust. Here are a few points that can be used as a reference.Bella,Before the elevator manufacturer connects the motor to the elevator, please make the keyway of the motor shaft perpendicular to the tightening bolt. In order to ensure uniform force, please screw on the mounting bolts at any diagonal position first, but do not tighten them tightly then screw on the other two mounting bolts at diagonal positions, and then tighten the four mounting bolts one by one. Finally, tighten the tension bolts. All tightening bolts need a torque wrench to fix according to the marked fixed torque data and check whether the lift and lifting platform are used.How should we check the construction site of the construction hoist? you know?Hydraulic pump station: special pump station for domestic lifting platform, protection device outside the pump station imported from Italy: organ m type, mesh type, iron plate seal type.Uses: The scissor-type fixed lifting platform is mostly used for the transportation of goods between the height differences of the production line, the loading and unloading of materials, the adjustment of the working height during the assembly of the workpiece, the feeding of the installed machine at a high place, the lifting of parts during the assembly of large equipment, and the storage and unloading place and Forklifts and other handling vehicles are used for fast loading and unloading of goods car lifting, fixed three-dimensional parking and other places.

Check the front page of the oil pipe to check whether the skin of the oil pipe of the hydraulic lifting platform is damaged or cracked, and if so,MinneapolisElevating cargo elevator, replace it immediately; secondly, check whether there is any sign of looseness at the connection between the oil pipe and the oil pipe, and if so, tighten it immediately to avoid lifting on the hydraulic lifting platform There is an oil spill in the process, which leads to accidents; what items need to be checked before using the hydraulic lifting platform? Cut off the power first to avoid tragedies such as electric leakage and electric shock)Looseness occurs: The newly processed and assembled parts of mobile lifts and other aerial work platform equipment have a tendency to geometric shape and matching size. , Coupled with excessive wear and other reasons, which is mainly used in industrial plants, restaurants, restaurants, warehouses, docks, workshops and other places that need to move goods vertically between high-rise buildings above the second floor. The low height is especially suitable for sites where the site is not suitable for digging pits. What problems do we need to pay attention to in these places where elevators are used?Safety and health,The design of the hydraulic lifting platform is unreasonable. When the designer designs the cylinder barrel and rod, if there is a problem with the design size and angle, then there will definitely be problems in the later stage. Therefore, it is necessary to confirm the technical strength of the manufacturer when working on a hydraulic lifting platform; what is the problem with the sound of the oil cylinder of the hydraulic lifting platform? Design drawings to make, the angle of the oil cylinder is slightly deviated, it will cause the friction between the cylinder barrel and the rod, and the use of different seals will also affect the sound of the oil cylinder, and the seal with excellent material The continuous friction between the parts and the cylinder wall will cause the sound to be very loud, and long-term wear and tear may scratch the oil cylinder and cause oil leakage, so when the hydraulic lifting platform is used, pay attention to ask the manufacturer what brand and material the seal is used; In some cases of mechanical running-in, it is not ruled out that the above three situations are normal and there will still be noises. If there is no problem after investigation, then don’t worry. It’s just a running-in problem between mechanical parts. It will disappear naturally.Prepare the foundation according to the foundation plan, pay attention to the alignment, leveling, and alignment to ensure the level of the foundation and various requirements for use.How to effectively prevent electric shock by using a hydraulic lifting platform It is very common to add a leakage protector, and the cost is not high. It is both affordable and safe, and can effectively prevent electric shock.

Hydraulic pump station: special pump station for domestic lifting platform, protection device outside the pump station imported from Italy: organ m type, mesh type, iron plate seal type.Packaging strategy,The hydraulic lifting platform is widely used in the maintenance of industrial and mining enterprises, municipal construction, and decoration of hotels and hotels, with reliable quality and perfect performance.It is easy for the chassis parts to cause oil deterioration in the process of wading, especially in the steering, transmission and other systems, the chassis should be disassembled and inspected. When the elevator enters the water, everyone must pay attention to it and need to check clearly. The point must not be ignored.Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation,MinneapolisElevating cargo elevator 1-4 floors, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, the lift also has a lot of safety equipment.Minneapolis,MinneapolisGood comments on cargo elevators,Frequently check whether the various mechanisms are operating normally and whether there is any noise. If a fault is found, it must be eliminated in time.The surface of the brushes of each part should be kept clean, and the pressure of the brushes should be adjusted so that the area is not less than %. Professional elevator factory, large quantity favorably high quality and low price. Fire-resistant-waterproof-high temperature resistant, durable, safe and reliable.The motor connection is wrong. When the delta connection motor is wrongly connected into a star shape, the motor still runs with full load, and the current flowing through the stator winding will exceed the rated current, and even cause the motor to stop by itself. If it overheats, or the motor with several coil groups connected in series to form a branch circuit is connected in parallel with two branches, it will cause the winding and core to overheat and in severe cases

In addition to the fixed mode, and of course it is more useful. For example There is this kind of lifting equipment in the airport, and it is also possible to install this kind of equipment in stations or stadiums. Since it can be moved, the scope of operation is not limited to a certain place, and it can be used wherever lifting operations are required. It can be used. For example, when installing outdoor advertisements, the height of some advertisements is relatively high. At this time, mobile lifting equipment can be used to send billboards or staff to the designated height to work. This kind of equipment can also be divided into two types according to the driving mode: hydraulic lifting and electric lifting. The so-called hydraulic lifting is driven by hydraulic oil to reach a specified height. The electric mode is driven by a motor or geared to lift to A certain height, but at present, hydraulic lifting platforms are more widely used.Secondly, there must be no dirt on the friction surface. If there is dirt,GenoaConstruction site lifting cargo elevator, it needs to be washed off with gasoline or thinner; the gear box, gearbox, external gear and other parts of the equipment and the hydraulic oil must be in accordance with the requirements in the table; Correctly maintain the hydraulic guide rail lift. Regularly check whether the wire ropes in each part are broken or loose. If this phenomenon is found, replace them in time. If there is any looseness, it should be tightened in time. The connecting bolts of the equipment should be checked for tightness when the body is under pressure. All connecting shafts should be equipped with cotter pins; check whether each mechanism is operating normally, whether there is noise or failure , to eliminate all faults in a timely manner; when installing, dismantling and adjusting the slewing mechanism of the equipment, whether the wires and cables are If there is damage, whether the motor is overheated replace it in time and continue to run after troubleshooting; ensure that the bearings of the motor, each box, distribution box and brushes must be kept clean, and the travel switch points of each safety device must be safe and reliable.Genoa,As long as we transport the lifting platformTake the measures that need to be taken during the transportation of the lifting platform in advance to prevent all possible problems, and then the difficulties will be solved. The above is the company's arrangement of the issues that need to be considered during the transportation of the elevator. These factors It is a factor that needs to be considered for every lifting platform. Therefore, we must try our best to be perfect and impeccable. For the failure problems that often occur in lifts and lifting platforms, many operators of the user units have no way to solve them. They must apply for a professional personnel to perform on-site repairs. However due to the obstacles of the working environment and time factors of the equipment, and only some special measures can be taken to maintain the basic working performance of the equipment.The design of the hydraulic lifting platform is unreasonable. When the designer designs the cylinder barrel and rod the failures of the equipment cannot be fully repaired normally, if there is a problem with the design size and angle, then there will definitely be problems in the later stage. Therefore, it is necessary to confirm the technical strength of the manufacturer when working on a hydraulic lifting platform; what is the problem with the sound of the oil cylinder of the hydraulic lifting platform? Design drawings to make, it will cause the friction between the cylinder barrel and the rod, which will cause the sound; the seal quality of the hydraulic lifting platform is different, and the use of different seals will also affect the sound of the oil cylinder, and the seal with excellent material The continuous friction between the parts and the cylinder wall will cause the sound to be very loud, and long-term wear and tear may scratch the oil cylinder and cause oil leakage, so when the hydraulic lifting platform is used, pay attention to ask the manufacturer what brand and material the seal is used; In some cases of mechanical running-in, it is not ruled out that the above three situations are normal, and there will still be noises. If there is no problem after investigation, then don’t worry. It’s just a running-in problem between mechanical parts. It will disappear naturally.Telsiai,The hydraulic lifting platform is widely used in the maintenance of industrial and mining enterprises, municipal construction, and decoration of hotels and hotels, with reliable quality and perfect performance.Features of hydraulic lifts: According to the working mode, hydraulic lifting platform products are divided into crank arm hydraulic lifting machines, scissor hydraulic lifting machines, mast type hydraulic lifts, and straight arm hydraulic lifting machines. The hydraulic lift is a replacement product of the folding arm lift (lifting platform) and the scissor lift (lifting platform). It can be widely used in stations,GenoaSimple lifting cargo elevator requires, docks, airports, hotels, post and telecommunications, municipal gardens garages, cleaning companies, public building facade decoration, decoration or installation and maintenance of power systems, self-propelled, electric start, self-supporting legs, simple operation, large working area, and its type selection is based on the heat load to calculate the heat exchange area, while its air-cooled elevator is carried out by using an air cooler, and it is The heat transfer capacity is calculated according to the heat load, and then the type selection calculation is carried out under the condition that the flow rate can be satisfied. Therefore, these two kinds of cooling are not the same, and there is a big difference. Long-term promotion of freight elevator factories and other, Long-term cooperation, mutual benefit and win-win. If you choose the wrong supplier, you will be overwhelmed with all kinds of after-sales troubles in the later stage. Recently, I have seen many netizens report the problem of very loud oil cylinders. Today, the editor will simply popularize the knowledge for everyone.

Low cost: The cost is much lower than that of the scissor-type mobile lifting platform, so when purchasing a lifting platform, the frequency of work, the load and other factors to choose a lifting platform that suits the work requirements .The loading and unloading mobile boarding bridge is already a very obvious structural form in the modern logistics scene. It is the point and end point of the enterprise's logistics chain, and a loading and unloading operation platform for the enterprise's fast and turnover products and goods. The height of the loading and unloading operation platform is fixed, but there is always a certain height drop or gap between the height of the transport vehicles and the loading and unloading platform. As a result, the handling forklift cannot directly load and unload goods in and out of the transport vehicle. Utilize a boarding bridge to provide a reliable connection. It enables the forklift to move in and out of the transport vehicle efficiently and quickly for loading and unloading operations.Hydraulic system: mainly oil cylinders, high-strength chrome-plated rods, Japanese NOK seals, self-made external integrated pump stations, oil pipelines, gear pumps, solenoid valves etc. The Japanese NOK seal used in the oil cylinder has good wear resistance, which ensures that the oil cylinder series will not leak oil for a long time. The gear pump pumps the oil in the oil tank into the oil circuit and enters the oil cylinder, thereby driving the top of the rod and raising the equipment; The valve is used to adjust the oil output, the ascending and descending speed, and contains an emergency descending device to ensure that the guide rail hydraulic lifting platform can descend safely in case of an emergency.For more, please check,Uses: The scissor-type fixed lifting platform is mostly used for the transportation of goods between the height differences of the production line, the loading and unloading of materials, the adjustment of the working height during the assembly of the workpiece, the feeding of the installed machine at a high place, the lifting of parts during the assembly of large equipment, and the storage and unloading place and Forklifts and other handling vehicles are used for fast loading and unloading of goods, car lifting, fixed three-dimensional parking and other places.Knowledge popularization of scissor-type fixed lifting platform Superior performance: equipped with safety devices to prevent overloading of the lifting platform; equipped with protection valves to prevent hydraulic oil pipes from breaking; equipped with emergency descending devices for sudden power failures; Lock safety device.In addition to the fixed mode, the elevator also has a vehicle-mounted mobile type. As the name implies, it combines the lifting equipment with the vehicle-mounted system. Such a lifting equipment is very flexible to move, and of course it is more useful. For example There is this kind of lifting equipment in the airport, and it is also possible to install this kind of equipment in stations or stadiums. Since it can be moved, the scope of operation is not limited to a certain place, and it can be used wherever lifting operations are required. It can be used. For example, when installing outdoor advertisements, mobile lifting equipment can be used to send billboards or staff to the designated height to work. This kind of equipment can also be divided into two types according to the driving mode: hydraulic lifting and electric lifting. The so-called hydraulic lifting is driven by hydraulic oil to reach a specified height. The electric mode is driven by a motor or geared to lift to A certain height, but at present, hydraulic lifting platforms are more widely used.

In the construction elevator, the switch box also has leakage protection equipment. Its wires and cables are well insulated,GenoaChain guide rail cargo elevator lifting, without leakage, and the metal threaded is not rusted, and its damage is close to zero. His steel wire rope should comply with the corresponding configuration requirements, and there is no problem of broken strands and diameter reduction. Of course, the number of broken wires should not exceed the corresponding standard. His pulley movement is very flexible.Product range,Prepare the foundation according to the foundation plan, pay attention to the alignment, leveling, and alignment to ensure the level of the foundation and various requirements for use.When working at heights, hang the hook of the self-locking device on the metal ring of the safety belt.In the construction elevator, the switch box also has leakage protection equipment. Its wires and cables are well insulated, without leakage, and the metal threaded is not rusted, and its damage is close to zero. His steel wire rope should comply with the corresponding configuration requirements, and there is no problem of broken strands and diameter reduction. Of course, the number of broken wires should not exceed the corresponding standard. His pulley movement is very flexible.Genoa,The common types of lifts are simply introduced here for you. I hope you can learn more about this product. At present, this product can be said to be sold well in China because many places need to use this product. Products that can be lifted and moved flexibly at the same time. Now companies that specialize in the production of this product combine a large-scale external publicity on the Internet. Friends in need can directly find the corresponding company on the Internet, and then simply learn about the models of these products and Information on performance and price can be purchased directly through the Internet.Goods should be stacked on the platform and not tilted. When the freight elevator goes up and down beyond the range of the platform, no one should stand around to watch.Hydraulic pump station: special pump station for domestic lifting platform, protection device outside the pump station imported from Italy: organ m type, mesh type, iron plate seal type.

In addition, during installation it is strictly forbidden to use hammers, etc. to prevent damage to bearings or gears due to excessive axial force or radial force. Be sure to tighten the mounting bolts before tightening the force bolts. Before installation, clean the anti-rust oil on the motor input shaft, and to prevent unnecessary wear and tear.Avoid working in an environment. In the event of rain, the use of the hydraulic lifting platform should be stopped to prevent the occurrence of a short circuit, resulting in electric leakage and electric shock; non-professionals are strictly prohibited from disassembling electrical appliances such as hydraulic lifting platforms. In the event of an accident, you can’t disassemble without permission to eliminate the cause. You must report to the manufacturer for repair in time, inform the phenomenon of the accident, and the manufacturer will guide you to complete the inspection or send someone to repair it; do not disassemble the appliance without permission! Professional elevator factory guarantees quality, guarantees service. Guarantees quality. Your satisfaction is our pursuit! Welcome to inquire.Perpignan,At this time, if the aerial work platform is overloaded, it may cause damage to parts and cause some mechanical failures. Professional elevator factory quality assurance, professional company, timely supply, high cost performance, has become the preferred brand of many wire products, welcome to buy!Prepare the foundation according to the foundation plan, pay attention to the alignment, leveling,Regular maintenance Regularly check whether the circuit system of the hydraulic lifting platform is loose, and check whether the wires and cables are aging and damaged, which may cause leakage of the line. If there is, it should be repaired in time to avoid electric shock.Many people think that the strength of the elevator itself is relatively high when using the elevator, so they did not strictly follow the installation method in the manual during the installation process, but they do not know that this will cause increased wear and tear of the parts and inflexible operation, and pay attention to the work The installation precautions corresponding to the environment should not be ignored. Correct installation, use and maintenance of elevators are an important part of ensuring the normal operation of mechanical equipment. Therefore, when you install the elevator, please be sure to strictly follow the installation and use related matters below, and assemble and use it carefully.What is the new price of a fixed lift? Professionally improve the quality assurance of the freight elevator factory. The preferential activities are in progress, and new and old customers are welcome to come to consult.

Low cost: The cost is much lower than that of the scissor-type mobile lifting platform, so when purchasing a lifting platform, you must consider the scope of use of the lifting platform, the frequency of work, the load and other factors to choose a lifting platform that suits the work requirements .Regular inspection and maintenance,Perpignan8-meter cargo elevator, elimination of hidden dangers, and troubleshooting are all good for improving work efficiency, prolonging the service life of equipment and ensuring the safety performance of the elevator.The scissor-type fixed lifting platform is a kind of transportation and handling equipment for transporting goods from a certain height to another height. After the operation is completed, the platform is level with the ground, does not occupy the ground space, and does not affect the passageway.Highly recommended,Naturally connect the motor to the lift. When connecting it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, and that the outer flanges of the two are parallel. If the concentricity is inconsistent, it will cause the motor shaft to break or the elevator gear to wear.Brake operators of various mechanisms on the equipment should regularly check and adjust the gap between the brake shoe and the brake wheel to ensure flexibility and reliability. Long-term promotion of freight elevator factory, old brand, quality guaranteed!Before the elevator manufacturer connects the motor to the elevator, please make the keyway of the motor shaft perpendicular to the tightening bolt. In order to ensure uniform force, please screw on the mounting bolts at any diagonal position first, but do not tighten them tightly, then screw on the other two mounting bolts at diagonal positions, and then tighten the four mounting bolts one by one. Finally, tighten the tension bolts. All tightening bolts need a torque wrench to fix according to the marked fixed torque data and check whether the lift and lifting platform are used.How should we check the construction site of the construction hoist? you know?

The scissor-type fixed lifting platform is a kind of transportation and handling equipment for transporting goods from a certain height to another height. After the operation is completed, the platform is level with the ground, does not occupy the ground space,PerpignanHigh performance elevator, and does not affect the passageway.Work courses,In addition to the fixed mode, the elevator also has a vehicle-mounted mobile type. As the name implies it combines the lifting equipment with the vehicle-mounted system. Such a lifting equipment is very flexible to move, and it is also possible to install this kind of equipment in stations or stadiums. Since it can be moved and of course it is more useful. For example There is this kind of lifting equipment in the airport, the scope of operation is not limited to a certain place, and it can be used wherever lifting operations are required. It can be used. For example, when installing outdoor advertisements, the height of some advertisements is relatively high. At this time,PerpignanWarehouse elevator, mobile lifting equipment can be used to send billboards or staff to the designated height to work. This kind of equipment can also be divided into two types according to the driving mode: hydraulic lifting and electric lifting. The so-called hydraulic lifting is driven by hydraulic oil to reach a specified height. The electric mode is driven by a motor or geared to lift to A certain height, but at present, hydraulic lifting platforms are more widely used.It is strictly forbidden for two persons working at heights to use the same safety rope at the same time.Test the freight elevator every day to see if the freight elevator can operate normally.Perpignan,After the goods are transported, coil group or one-phase winding is reversed, it will cause a serious imbalance in the three-phase current and cause the winding to overheat.What are the maintenance rules for hydraulic lift machinery? The brakes of each mechanism should be checked frequently and the gap between the brake shoe and the brake wheel should be adjusted to ensure flexibility and reliability. There should be no dirt on the friction surface, and if there is dirt, it must be washed off with gasoline or thinner.

Are the water cooling and air cooling of the hydraulic station the same?The load of this series of products is divided into . to . tons, and can also be customized according to user requirements, with a load of up to tons.Dalas,Check whether the self-locking device of the differential protector is normal before working at heights.Always check the connections of the various parts of the hydraulic lift, and tighten them if they are loose. The tightness of the connecting bolts of the body should be checked when the body is under pressure.Vernier,The contact opening and closing of the travel switch of each safety device must be reliable, and the contact arc crater should be polished in time.Always check the connections of the various parts of the hydraulic lift, and tighten them if they are loose. The tightness of the connecting bolts of the body should be checked when the body is under pressure.Are the water cooling and air cooling of the hydraulic station the same?

The water cooling of the hydraulic station is generally tube-type water cooling, and its type selection is based on the heat load to calculate the heat exchange area while its air-cooled elevator is carried out by using an air cooler, and it is The heat transfer capacity is calculated according to the heat load, and then the type selection calculation is carried out under the condition that the flow rate can be satisfied. Therefore, and there is a big difference. Long-term promotion of freight elevator factories and other, Long-term cooperation, mutual benefit and win-win. If you choose the wrong supplier, you will be overwhelmed with all kinds of after-sales troubles in the later stage. Recently, I have seen many netizens report the problem of very loud oil cylinders. Today, the editor will simply popularize the knowledge for everyone.The lifting height is stable, which can meet the smooth lifting of large-tonnage cargo. The hydraulic lifting stage is equipped with an anti-attachment and overload protection hydraulic system to ensure operation. It is a long-term operating freight elevator factory. Welcome to consult.Check the front page of the oil pipe to check whether the skin of the oil pipe of the hydraulic lifting platform is damaged or cracked, and if so, replace it immediately; secondly, check whether there is any sign of looseness at the connection between the oil pipe and the oil pipe, and if so, tighten it immediately to avoid lifting on the hydraulic lifting platform There is an oil spill in the process, which leads to accidents; what items need to be checked before using the hydraulic lifting platform? Cut off the power first to avoid tragedies such as electric leakage and electric shock)Interpretation and observation,The daily maintenance of the hydraulic lifting platform in normal use is essential but even if there is normal maintenance on the equipment, any possible problem cannot be ignored, the editor will give you a popular science.Check the limit switch to see if all the limit switches are loose. If so,Dalas2 ton lifting cargo elevator, please tighten them. Pay special attention to the ultra-high protection stroke of the hydraulic lifting platform to avoid accidents caused by the equipment exceeding the high safety height; check the pins (ear pins and center pins) Check whether the nuts, nuts, screws, etc. are loose, should be reinforced immediately; ensure that the hydraulic lifting platform rises and falls smoothly; outriggers (for high-altitude operating platform)The contact opening and closing of the travel switch of each safety device must be reliable and the contact arc crater should be polished in time.

How to effectively prevent electric shock by using a hydraulic lifting platform It is very common to add a leakage protector, and the cost is not high. It is both affordable and safe, and can effectively prevent electric shock.Honest service,Test the freight elevator every day to see if the freight elevator can operate normally.It is forbidden to stay under the high-altitude operation site, and safety nets or other protective devices should be installed under the work site to avoid injury caused by falling objects.The use of elevators is not to maintain and overhaul after the equipment fails. It is necessary to maintain the equipment according to the correct maintenance and overhaul, and start with the preparation work to prevent all possible failures and accidents. I hope that the editor can summarize the knowledge points today. Help everyone.Dalas,How to effectively prevent electric shock by using a hydraulic lifting platform It is very common to add a leakage protector, and the cost is not high. It is both affordable and safe,DalasA cargo elevator, and can effectively prevent electric shock.It is strictly forbidden to switch the electric control switch with wet hands. Many people tend to ignore this detail. Although the safety voltage of the hydraulic lifting platform is below V, if you touch the power supply with your hands,Dalas4-ton cargo elevator, it may cause lifting failure in light cases, or electric shock accidents in severe cases.Check the limit switch to see if all the limit switches are loose. If so, please tighten them. Pay special attention to the ultra-high protection stroke of the hydraulic lifting platform to avoid accidents caused by the equipment exceeding the high safety height; check the pins (ear pins and center pins) Check whether the nuts, nuts, screws, etc. are loose, if any, should be reinforced immediately; ensure that the hydraulic lifting platform rises and falls smoothly; outriggers (for high-altitude operating platform)

After the goods are transported clean up the debris on the platform.The safety device and application of the guide rail hydraulic lifting platform The use of the guide rail hydraulic lifting platform The guide rail hydraulic lifting platform is a non-scissor hydraulic lifting freight elevator. It is used for goods between different floors of industrial plants, restaurants restaurants, etc. The low height can be made to -mm. The advantage is that it can be placed directly on the ground without digging pits, reducing engineering construction costs, and there is no need to set up hanging points on the top, which is safe. Reliable; the hydraulic lifting platform adopts hydraulic transmission mode, and can be non-calibrated according to customer needsSeveral types: Motor winding open circuit. When one of the motor windings is disconnected, or one of the parallel branches is disconnected the three-phase current will be unbalanced and the motor will overheat.Palais de Versailles,Looseness occurs: The newly processed and assembled parts of mobile lifts and other aerial work platform equipment have a tendency to geometric shape and matching size. , Coupled with excessive wear and other reasons, it is easy to loosen the originally fastened parts of aerial work platform equipment such as mobile lifts.The daily maintenance of the hydraulic lifting platform in normal use is essential, but even if there is normal maintenance on the equipment, any possible problem cannot be ignored, so in order to ensure that the process of using the hydraulic lifting platform for each operation What aspects do we need to check before operation? Today, the editor will give you a popular science.Talaz,Use Hydraulic lifts are widely used in various industrial enterprises and production lines such as automobiles, containers, mold manufacturing, wood processing, chemical filling, etc., to meet the lifting needs of different operating heights, and can be equipped with various table forms (such as balls, rollers, Turntable, steering, tilting, telescopic), with various methods (separate, linkage, explosion-proof), with the characteristics of stable and accurate lifting, frequent starting, large load capacity, etc., effectively solving the difficulties of various lifting operations in industrial enterprises, so that Production operations freely. The professional elevator factory has advanced technology, strict testing, more affordable prices, and more discounts are in progress, welcome to consult.In addition to the fixed mode,Palais de VersaillesHydraulic guide rail type cargo elevator, the elevator also has a vehicle-mounted mobile type. As the name implies, it combines the lifting equipment with the vehicle-mounted system. Such a lifting equipment is very flexible to move, and of course it is more useful. For example There is this kind of lifting equipment in the airport, the scope of operation is not limited to a certain place, and it can be used wherever lifting operations are required. It can be used. For example, when installing outdoor advertisements, the height of some advertisements is relatively high. At this time, mobile lifting equipment can be used to send billboards or staff to the designated height to work. This kind of equipment can also be divided into two types according to the driving mode: hydraulic lifting and electric lifting. The so-called hydraulic lifting is driven by hydraulic oil to reach a specified height. The electric mode is driven by a motor or geared to lift to A certain height but at present, if you touch the power supply with your hands, it may cause lifting failure in light cases, or electric shock accidents in severe cases.

It is strictly forbidden to switch the electric control switch with wet hands. Many people tend to ignore this detail. Although the safety voltage of the hydraulic lifting platform is below V, if you touch the power supply with your hands it may cause lifting failure in light cases, or electric shock accidents in severe cases.Maintenance should implement the 'Special Equipment Supervision Regulations', 'Elevator Supervision and Inspection Regulations', industry standards and local standards.Check the front page of the oil pipe to check whether the skin of the oil pipe of the hydraulic lifting platform is damaged or cracked, and if so, replace it immediately; secondly, check whether there is any sign of looseness at the connection between the oil pipe and the oil pipe, and if so, tighten it immediately to avoid lifting on the hydraulic lifting platform There is an oil spill in the process, which leads to accidents; what items need to be checked before using the hydraulic lifting platform? Cut off the power first to avoid tragedies such as electric leakage and electric shock)Good reputation,System: explosion-proof electronic control system, remote control system, P IC system.The last thing to note is that, compared with the lifting platforms in some places, protective fences are generally added on the platforms. Since the lifting platforms are special equipment,Palais de VersaillesFive ton cargo elevator, the National Quality Inspection Bureau is very strict on this piece of inspection. All must be dismantled, so when the personnel ask you if you want to add a guardrail, don't blindly refuse, and consider whether it is necessary according to the site of use. In addition, you must have the 'People's Republic of Special Equipment Manufacturing License' and the 'People's Republic of Special Equipment Installation, Transformation and Maintenance License' to produce, install, and maintain. Therefore you must ask whether the manufacturer has these two certificates.The price is guaranteed, the service is guaranteed, and it is a large-scale logistics and storage equipment service company directly operated by the manufacturer. Since the fixed lift is a mechanical device, the quality and performance of the product must be good. Do not accept the products of some manufacturers whose quality is not up to standard, so as to avoid some safety hazards in use.

The anti-rust work of the aerial work vehicle generally needs to be paid attention to when the aerial work vehicle has not been used for a long time. How should we do anti-corrosion for the body of the aerial work vehicle? This is actually very simple. You don’t need to spend money to go to the repair station for anti-corrosion. As long as our car owners use some materials that they can find at hand, it can be realized. At the same time, paying attention to driving habits can ensure that the aerial work vehicle does not rust. Here are a few points that can be used as a reference.Economic management,Use Hydraulic lifts are widely used in various industrial enterprises and production lines such as automobiles, containers, mold manufacturing, wood processing, chemical filling, etc., to meet the lifting needs of different operating heights, and can be equipped with various table forms (such as balls, rollers, Turntable steering, tilting, telescopic), explosion-proof), with the characteristics of stable and accurate lifting frequent starting, large load capacity, etc., effectively solving the difficulties of various lifting operations in industrial enterprises, so that Production operations freely. The professional elevator factory has advanced technology, strict testing, more affordable prices, welcome to consult.With the increase in the demand for boarding bridges, mobile boarding bridges are increasingly favored by mobile boarding bridges to show customers the appearance of hydraulic boarding bridges, and the demand for boarding bridges is also increasing. However, there are not many corresponding boarding bridge manufacturers. Many boarding bridge companies are leather bag companies. When the customer's technical requirements are given to the manufacturer, there will often be deviations, so customers who purchase boarding bridges are best to find a professional manufacturer directly. When purchasing a boarding bridge, you must first comprehensively consider factors such as the scope of use of the product, frequency of work, utilization rate, rated weight, etc., and choose a boarding bridge suitable for the use requirements of the unit. Carry out market research according to the proposed technical parameters. To choose a supplier, the first condition is to look at the manufacturer of the climbing bridge, and then the after-sales service capability. As long as it is a fixed boarding bridge with good product quality, excellent performance and complete equipment,Palais de VersaillesRail lift cargo elevator, it can be used as the object of choice if the price is reasonable.Mechanisms: Mechanisms such as tabletops, track grooves, wire ropes, chains, and pulleys are made of solid materials to ensure safety.Palais de Versailles,What is the new price of a fixed lift? Professionally improve the quality assurance of the freight elevator factory. The preferential activities are in progress, and new and old customers are welcome to come to consult.Precautions for elevator installation Keep the access road of the external construction elevator smooth and have enough parking space for equipment. When it is necessary to use a steam crane for auxiliary installation, it should be fully considered whether the site environment meets the operating conditions of the steam crane.The elevator is a kind of elevator equipment composed of traveling mechanism, electric mechanism and supporting mechanism. The hydraulic oil is under a certain pressure formed by the vane pump, and enters the lower end of the hydraulic cylinder through the oil filter, explosion-proof electromagnetic reversing valve, hydraulic control check valve, and balance valve, so that the upward movement of the hydraulic cylinder can lift heavy objects , The oil returned from the upper end of the hydraulic cylinder returns to the oil tank through the explosion-proof electromagnetic reversing valve, and the rated pressure relief valve is adjusted, and the pressure gauge reads the pressure gauge.