Precautions for elevator installation Keep the access road of the external construction elevator smooth and have enough parking space for equipment. When it is necessary to use a steam crane for auxiliary installation, it should be fully considered whether the site environment meets the operating conditions of the steam crane.Ensure good power supply at the installation site, install a separate distribution box,HermondGuide rail chain lifting cargo elevator, and the leakage switch must meet the requirements for construction elevators when used in the distribution box. If the construction elevator installed is frequency conversion, the leakage switch should be adapted to the frequency converter when selecting the leakage switch .Hermond,It is strictly forbidden to use the seat belt to transfer heavy objects; the seat belt should be hung on a firm and reliable place above, and the height of the seat belt is higher than the waist. The professional elevator factory is safe,HermondGuide rail lifting cargo elevator, environmentally friendly and economical! The products are exported to foreign countries and are deeply trusted.Low cost: The cost is much lower than that of the scissor-type mobile lifting platform, so when purchasing a lifting platform, you must consider the scope of use of the lifting platform, the frequency of work, the load and other factors to choose a lifting platform that suits the work requirements .Louga,Knowledge popularization of scissor-type fixed lifting platform Superior performance: equipped with safety devices to prevent overloading of the lifting platform; equipped with protection valves to prevent hydraulic oil pipes from breaking; equipped with emergency descending devices for sudden power failures; Lock safety device.Many customers think that the operating power supply of the hydraulic lifting platform is below the safe voltage of V, and there will be no electric shock. They are wrong. Normally, there will be no electric shock, but if there is improper operation, it will still be very dangerous. So how can we effectively prevent the occurrence of electric shock accidents? Today, the editor will share safety knowledge with you.Guide rail lift (also known as freight elevator) is a non-scissor hydraulic lifting platform, which is mainly used in industrial plants, restaurants, restaurants, warehouses, docks, workshops and other places that need to move goods vertically between high-rise buildings above the second floor. The low height is especially suitable for sites where the site is not suitable for digging pits. What problems do we need to pay attention to in these places where elevators are used?

Many customers think that the operating power supply of the hydraulic lifting platform is below the safe voltage of V, and there will be no electric shock. They are wrong. Normally, there will be no electric shock, but if there is improper operation, it will still be very dangerous. So how can we effectively prevent the occurrence of electric shock accidents? Today, the editor will share safety knowledge with you.Check rollers, it can be realized. At the same time, paying attention to driving habits can ensure that the aerial work vehicle does not rust. Here are a few points that can be used as a reference.production,Before the elevator manufacturer connects the motor to the elevator, please make the keyway of the motor shaft perpendicular to the tightening bolt. In order to ensure uniform force, please screw on the mounting bolts at any diagonal position first, but do not tighten them tightly, then screw on the other two mounting bolts at diagonal positions, and then tighten the four mounting bolts one by one. Finally, tighten the tension bolts. All tightening bolts need a torque wrench to fix according to the marked fixed torque data and check whether the lift and lifting platform are used.How should we check the construction site of the construction hoist? you know?The motor connection is wrong. When the delta connection motor is wrongly connected into a star shape, the motor still runs with full load, and the current flowing through the stator winding will exceed the rated current and even cause the motor to stop by itself. If it overheats, it will burn out. When the star-connected motor is wrongly connected into a triangle, or the motor with several coil groups connected in series to form a branch circuit is connected in parallel with two branches, it will cause the winding and core to overheat, and in severe cases, the winding will be burned.Anti-corrosion measures for the body of aerial work vehicles Pay attention to small scratches. The paint surface of aerial work vehicles is often corroded. In addition to common collisions, scratches, small rocks on the driving tires, there may also be a peeling paint spot, and a small rust will appear after a long time. Because most of these scars are small, check regularly, the engine compartment cover and its surroundings, and once found, go to a professional beauty shop for processing.

Conscientiously write the special construction plan for installation and construction, and make safety technical disclosures to the installers.OK or not?,In addition,Hermond1 ton small lifting cargo elevator, during installation, it is strictly forbidden to use hammers, etc. to prevent damage to bearings or gears due to excessive axial force or radial force. Be sure to tighten the mounting bolts before tightening the force bolts. Before installation, clean the anti-rust oil on the motor input shaft, the positioning boss and the connection parts of the elevator with gasoline or zinc and sodium water. Its purpose is to ensure the tightness of the connection and the flexibility of operation, and to prevent unnecessary wear and tear.Attention should be paid to checking whether there are any broken wires and loose strands in the wire ropes of each part. If it exceeds the relevant regulations, the short-circuit current is much larger than the normal operating current which increases the copper loss of the winding, causing the winding to overheat and even burn out.Hermond,System: explosion-proof electronic control system, remote control system, P IC system.Hydraulic pump station: special pump station for domestic lifting platform, protection device outside the pump station imported from Italy: organ m type mesh type, iron plate seal type.The cleanliness of the hydraulic station is an important aspect of the elevator hydraulic station, from a professional point of view, there are relevant rules and requirements, and you should refer to the specification manual, so that you can have a correct understanding and know how to achieve better cleanliness.

Check the limit switch to see if all the limit switches are loose. If so, please tighten them. Pay special attention to the ultra-high protection stroke of the hydraulic lifting platform to avoid accidents caused by the equipment exceeding the high safety height; check the pins (ear pins and center pins) Check whether the nuts, nuts, screws, if any, should be reinforced immediately; ensure that the hydraulic lifting platform rises and falls smoothly; outriggers (for high-altitude operating platform)Walking: assisted self-propelled, two-wheel traction, self-driving, and car modified.Cologne,It adopts a scissor-type mechanical structure, so that the aerial work platform can still move stably when it carries a large weight and rises to a large working height. It is its larger range of high-altitude operations and carrying capacity that make it widely used in various fields. The self-propelled scissor-type aerial work platform can walk quickly or slowly at various heights during operation, and can conveniently and continuously complete operations such as forward, backward, up and down, left and right steering on the operating platform. Make high-altitude operations more efficient and more secure. Therefore, and tighten them if they are loose. The tightness of the connecting bolts of the body should be checked when the body is under pressure.Roxas,What is the new price of a fixed lift? Professionally improve the quality assurance of the freight elevator factory. The preferential activities are in progress, and new and old customers are welcome to come to consult.Outriggers: mechanical outriggers, hydraulic outriggers, ordinary hand-operated outriggers, pull-out outriggers.The design of the hydraulic lifting platform is unreasonable. When the designer designs the cylinder barrel and rod, if there is a problem with the design size and angle, then there will definitely be problems in the later stage. Therefore, it is necessary to confirm the technical strength of the manufacturer when working on a hydraulic lifting platform; what is the problem with the sound of the oil cylinder of the hydraulic lifting platform? Design drawings to make, the angle of the oil cylinder is slightly deviated, it will cause the friction between the cylinder barrel and the rod, which will cause the sound; the seal quality of the hydraulic lifting platform is different, and the use of different seals will also affect the sound of the oil cylinder, and the seal with excellent material The continuous friction between the parts and the cylinder wall will cause the sound to be very loud, and long-term wear and tear may scratch the oil cylinder and cause oil leakage, so when the hydraulic lifting platform is used, pay attention to ask the manufacturer what brand and material the seal is used; In some cases of mechanical running-in, it is not ruled out that the above three situations are normal, and there will still be noises. If there is no problem after investigation, then don’t worry. It’s just a running-in problem between mechanical parts. It will disappear naturally.

In addition, during installation it is strictly forbidden to use hammers, etc. to prevent damage to bearings or gears due to excessive axial force or radial force. Be sure to tighten the mounting bolts before tightening the force bolts. Before installation, clean the anti-rust oil on the motor input shaft, the positioning boss and the connection parts of the elevator with gasoline or zinc and sodium water. Its purpose is to ensure the tightness of the connection and the flexibility of operation, and to prevent unnecessary wear and tear.: The rust of the screw jack is because the material of some manufacturers is not stainless steel. If the rust is not serious you can use sand paper to polish it to remove rust.Is there any way to solve the inadequacy of the surface rust of the screw elevator: the sand paper has a large loss on the screw elevator itself. Specializes in products, renewable resources business, hydraulic mechanism, electric mechanism and supporting mechanism. The hydraulic oil is under a certain pressure formed by the vane pump, and enters the lower end of the hydraulic cylinder through the oil filter, explosion-proof electromagnetic reversing valve, throttle valve, hydraulic control check valve, and balance valve, so that the upward movement of the hydraulic cylinder can lift heavy objects , The oil returned from the upper end of the hydraulic cylinder returns to the oil tank through the explosion-proof electromagnetic reversing valve, and the rated pressure relief valve is adjusted, and the pressure gauge reads the pressure gauge.Welcome calls ,CologneElevating cargo elevator,It is strictly forbidden to switch the electric control switch with wet hands. Many people tend to ignore this detail. Although the safety voltage of the hydraulic lifting platform is below V, if you touch the power supply with your hands it may cause lifting failure in light cases, or electric shock accidents in severe cases.In addition to the fixed mode, the elevator also has a vehicle-mounted mobile type. As the name implies, it combines the lifting equipment with the vehicle-mounted system. Such a lifting equipment is very flexible to move, and of course it is more useful. For example There is this kind of lifting equipment in the airport, and it is also possible to install this kind of equipment in stations or stadiums. Since it can be moved, the scope of operation is not limited to a certain place, and it can be used wherever lifting operations are required. It can be used. For example, when installing outdoor advertisements, the height of some advertisements is relatively high. At this time, mobile lifting equipment can be used to send billboards or staff to the designated height to work. This kind of equipment can also be divided into two types according to the driving mode: hydraulic lifting and electric lifting. The so-called hydraulic lifting is driven by hydraulic oil to reach a specified height. The electric mode is driven by a motor or geared to lift to A certain height, but at present, hydraulic lifting platforms are more widely used.Regular maintenance Regularly check whether the circuit system of the hydraulic lifting platform is loose, and check whether the wires and cables are aging and damaged, which may cause leakage of the line. If there is, it should be repaired in time to avoid electric shock.

The parts such as reduction box, gearbox, external gear and hydraulic oil are all in accordance with the requirements in the table.Test method,Frequently check whether the various mechanisms are operating normally and whether there is any noise. If a fault is found, it must be eliminated in time.The 'streamlined' open loose-leaf joint design of the hydraulic boarding bridge increases the welding area by more than times compared with the general tubular joint, which effectively prolongs the service life and simplifies maintenance.Regarding the cleanliness of the hydraulic station, is there any relevant rule requirement?Cologne,Features of hydraulic lifts: According to the working mode, hydraulic lifting platform products are divided into crank arm hydraulic lifting machines, scissor hydraulic lifting machines, mast type hydraulic lifts,CologneSmall lifting cargo elevator, and straight arm hydraulic lifting machines. The hydraulic lift is a replacement product of the folding arm lift (lifting platform) and the scissor lift (lifting platform). It can be widely used in stations, docks, airports, hotels, post and telecommunications, municipal gardens, garages cleaning companies, public building facade decoration, decoration or installation and maintenance of power systems,Cologne1 ton small lifting cargo elevator, electric start, self-supporting legs, simple operation, large working area especially the ability to cross obstacles for high-altitude operations and the like.Are the water cooling and air cooling of the hydraulic station the same?Safety performance: The lifting structure is made of high-strength manganese steel rectangular tube, and the scissor-type mechanical mechanism is easy to maintain, and the maximum load is about tons. .

The use of elevators is not to maintain and overhaul after the equipment fails. It is necessary to maintain the equipment according to the correct maintenance and overhaul,Malheim DrurTwo layers of hydraulic lifting cargo elevator, and start with the preparation work to prevent all possible failures and accidents. I hope that the editor can summarize the knowledge points today. Help everyone.Avoid working in an environment. In the event of rain, snow and other weather, the use of the hydraulic lifting platform should be stopped to prevent the occurrence of a short circuit, resulting in electric leakage and electric shock; non-professionals are strictly prohibited from disassembling electrical appliances such as hydraulic lifting platforms. In the event of an accident, you can’t disassemble without permission to eliminate the cause. You must report to the manufacturer for repair in time, inform the phenomenon of the accident,Malheim DrurSimple lifting cargo elevator for factory building, and the manufacturer will guide you to complete the inspection or send someone to repair it; do not disassemble the appliance without permission! Professional elevator factory guarantees quality, guarantees service. Guarantees quality. Your satisfaction is our pursuit! Welcome to inquire.Malheim Drur,Aluminum alloy elevators are also called aluminum alloy lifting platforms. At present, there are many types in the Chinese market, and they are very popular among users because of their flexible movement, light weight and small size.If the motor of the hydraulic lift is overheated, stop the machine in time and continue running after troubleshooting. The motor bearings must be in good condition.Shedertzee,Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, single-phase or three-phase power supply and diesel engine.The wrong connection of the motor of the elevator When a coil, coil group or one-phase winding is reversed, it will cause a serious imbalance in the three-phase current and cause the winding to overheat.

Frequently check whether the various mechanisms are operating normally and whether there is any noise. If a fault is found, it must be eliminated in time.The lifting platform has been inspected and debugged before leaving the factory, and all technical indicators meet the design requirements. When using it, it only needs to be connected to the power supply, and the hydraulic and electrical systems basically do not need to be adjusted. Our company is engaged in all kinds of materials such as elevator factories all the year round, and make safety technical disclosures to the installers.Sales Department,Regarding the cleanliness of the hydraulic station, is there any relevant rule requirement?The hydraulic lifting platform is widely used in the maintenance of industrial and mining enterprises, with reliable quality and perfect performance.If the motor of the hydraulic lift is overheated,Malheim DrurGuide rail lifting cargo elevator lifting, stop the machine in time and continue running after troubleshooting. The motor bearings must be in good condition.

Naturally connect the motor to the lift. When connecting, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, and that the outer flanges of the two are parallel. If the concentricity is inconsistent, it will cause the motor shaft to break or the elevator gear to wear.Online consultation,Features of hydraulic lifts: According to the working mode, hydraulic lifting platform products are divided into crank arm hydraulic lifting machines, scissor hydraulic lifting machines, mast type hydraulic lifts, and straight arm hydraulic lifting machines. The hydraulic lift is a replacement product of the folding arm lift (lifting platform) and the scissor lift (lifting platform). It can be widely used in stations, docks, airports, hotels post and telecommunications, municipal gardens, garages cleaning companies, public building facade decoration, decoration or installation and maintenance of power systems, etc. The lift has the advantages of light weight, self-propelled, electric start self-supporting legs, simple operation, large working area, especially the ability to cross obstacles for high-altitude operations and the like.There are abnormal noises on the hydraulic lifting platform It is a normal phenomenon that the hydraulic lifting platform has abnormal noises, especially for equipment that has been used for a long time. Overloading: Due to overloading, the hydraulic lifting platform's own carrying capacity is overloaded, just like the reason why people will shout when they are overloaded to carry things, so don't overload!Outriggers: mechanical outriggers, hydraulic outriggers, ordinary hand-operated outriggers, pull-out outriggers.Malheim Drur,The scissor-type fixed lifting platform is a kind of transportation and handling equipment for transporting goods from a certain height to another height. After the operation is completed, the platform is level with the ground, does not occupy the ground space, and does not affect the passageway.The load of this series of products is divided into . to . tons, and can also be customized according to user requirements, with a load of up to tons.Uses: The scissor-type fixed lifting platform is mostly used for the transportation of goods between the height differences of the production line, the loading and unloading of materials, the adjustment of the working height during the assembly of the workpiece, the feeding of the installed machine at a high place, the lifting of parts during the assembly of large equipment, and the storage and unloading place and Forklifts and other handling vehicles are used for fast loading and unloading of goods, car lifting, fixed three-dimensional parking and other places.

Knowledge popularization of scissor-type fixed lifting platform Superior performance: equipped with safety devices to prevent overloading of the lifting platform; equipped with protection valves to prevent hydraulic oil pipes from breaking; equipped with emergency descending devices for sudden power failures; Lock safety device.The hydraulic lifting platform can be divided into: four-wheel mobile type, two-wheel traction type, car modified type, car type, auxiliary self-propelled type, and the lifting height ranges from a meter to s meter.Rostock,It is forbidden to use hemp rope as a safety rope when using a mobile lift for high-altitude operations.Prepare the foundation according to the foundation plan, pay attention to the alignment, leveling, and alignment to ensure the level of the foundation and various requirements for use.high virtue,Fixed lift is a kind of transportation equipment that directly lifts and unloads goods from the ground. It is mostly used in places such as goods transportation between height differences in production lines, materials on and off the assembly line, parts lifting during large-scale equipment assembly, and fixed three-dimensional parking. So what is the new price of the fixed lift?The wrong connection of the motor of the elevator When a coil, coil group or one-phase winding is reversed, the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.It is strictly forbidden to use helmets beyond the validity period. The validity period of helmets is counted from the date of delivery. Plastic helmets shall not exceed two and a half years, and fiberglass helmets shall not be used for more than three and a half years.Frequently check whether the various mechanisms are operating normally and whether there is any noise. If a fault is found, it must be eliminated in time.technological innovation,Pay attention to check whether there are any broken wires and loose strands in the wire ropes of each part. If it exceeds the relevant regulations, it must be replaced immediately. The maintenance of the wire rope should be strictly in accordance with regulations.The load of this series of products is divided into . to . tons, and can also be customized according to user requirements, with a load of up to tons.The last thing to note is that, compared with the lifting platforms in some places protective fences are generally added on the platforms. Since the lifting platforms are special equipment, the National Quality Inspection Bureau is very strict on this piece of inspection. All must be dismantled so when the personnel ask you if you want to add a guardrail, don't blindly refuse, and consider whether it is necessary according to the site of use. In addition, you must have the 'People's Republic of Special Equipment Manufacturing License' and the 'People's Republic of Special Equipment Installation, install, and maintain. Therefore, you must ask whether the manufacturer has these two certificates.

Avoid working in an environment. In the event of rain, snow and other weather, the use of the hydraulic lifting platform should be stopped to prevent the occurrence of a short circuit, resulting in electric leakage and electric shock; non-professionals are strictly prohibited from disassembling electrical appliances such as hydraulic lifting platforms. In the event of an accident, you can’t disassemble without permission to eliminate the cause. You must report to the manufacturer for repair in time, inform the phenomenon of the accident, and the manufacturer will guide you to complete the inspection or send someone to repair it; do not disassemble the appliance without permission! Professional elevator factory guarantees quality, guarantees service. Guarantees quality. Your satisfaction is our pursuit! Welcome to inquire.Convenient and efficient,The hydraulic lifting platform can be divided into: four-wheel mobile type, two-wheel traction type, car modified type, car type, auxiliary self-propelled type, and the lifting height ranges from a meter to s meter.For the introduction to the daily maintenance of the elevator, the brakes of each organization should be regularly inspected and the distance between the brake shoe and the brake wheel should be adjusted to ensure flexibility and reliability. On the surface, there should be no dirt, and if there is dirt, it must be washed off with gasoline or thinner.The hydraulic lifting platform is widely used in the maintenance of industrial and mining enterprises, municipal construction, and decoration of hotels and hotels,Rostock6-ton cargo elevator,RostockChain guide rail cargo elevator lifting, with reliable quality and perfect performance.Rostock,After the goods are transported clean up the debris on the platform.Frequently check whether the various mechanisms are operating normally and whether there is any noise. If a fault is found, it must be eliminated in time.Before using the aerial work platform, it is necessary to confirm whether the outriggers are well supported, and then proceed with the operation; the rollers and slideways confirm whether the roller slideways of the hydraulic lifting platform are dry, and if there is When drying the site, an appropriate amount of butter should be added to ensure the smoothness during operation and to avoid head-to-head wear between mechanical parts.

Outriggers: mechanical outriggers, ordinary hand-operated outriggers, pull-out outriggers.When installing, dismantling and adjusting the slewing mechanism, care should be taken to ensure that the centerline of the slewing mechanism reducer is parallel to the centerline of the gear, the meshing surface is not less than %, and the meshing clearance is suitable.Saint Denis,Drain the hydraulic oil of the hydraulic lift and discard it. Tighten the joint to take out the oil filter. After cleaning, then put it back into the oil tank and connect the pipeline.The safety device and application of the guide rail hydraulic lifting platform The use of the guide rail hydraulic lifting platform The guide rail hydraulic lifting platform is a non-scissor hydraulic lifting freight elevator. It is used for goods between different floors of industrial plants, restaurants, etc. The low height can be made to -mm. The advantage is that it can be placed directly on the ground without digging pits,Saint DenisSimple lifting cargo elevator requires, reducing engineering construction costs, and there is no need to set up hanging points on the top, which is safe. Reliable; the hydraulic lifting platform adopts hydraulic transmission mode, and can be non-calibrated according to customer needsSeveral types: Motor winding open circuit. When one of the motor windings is disconnected, or one of the parallel branches is disconnected, the three-phase current will be unbalanced and the motor will overheat.Barara,Use Hydraulic lifts are widely used in various industrial enterprises and production lines such as automobiles, containers, mold manufacturing, wood processing, chemical filling, etc., to meet the lifting needs of different operating heights, and can be equipped with various table forms (such as balls, rollers, Turntable, steering tilting, telescopic), with various methods (separate, linkage, explosion-proof), with the characteristics of stable and accurate lifting, frequent starting, large load capacity,Saint DenisOutdoor guide rail type cargo elevator, etc., effectively solving the difficulties of various lifting operations in industrial enterprises, so that Production operations freely. The professional elevator factory has advanced technology, strict testing, more affordable prices and more discounts are in progress, welcome to consult.What are the maintenance rules for hydraulic lift machinery? The brakes of each mechanism should be checked frequently and the gap between the brake shoe and the brake wheel should be adjusted to ensure flexibility and reliability. There should be no dirt on the friction surface, and if there is dirt, and the dust on the electrical equipment is cleaned in time.

Goods should be stacked on the platform and not tilted. When the freight elevator goes up and down beyond the range of the platform, no one should stand around to watch.: Chemical derusting mainly uses acid to react chemically with the metal parts of the screw jack to remove the rust products on the rusty surface of the push rod. This kind of derusting is mainly used for large-scale mechanical screw jacks. During the process, electronic instruments and other precision components are protected from acid corrosion.Uses: The scissor-type fixed lifting platform is mostly used for the transportation of goods between the height differences of the production line, the loading and unloading of materials, the adjustment of the working height during the assembly of the workpiece, the feeding of the installed machine at a high place, the lifting of parts during the assembly of large equipment, and the storage and unloading place and Forklifts and other handling vehicles are used for fast loading and unloading of goods, car lifting, fixed three-dimensional parking and other places.Credit guarantee,Check the front page of the oil pipe to check whether the skin of the oil pipe of the hydraulic lifting platform is damaged or cracked, and if so, replace it immediately; secondly, check whether there is any sign of looseness at the connection between the oil pipe and the oil pipe, and if so, tighten it immediately to avoid lifting on the hydraulic lifting platform There is an oil spill in the process which leads to accidents; what items need to be checked before using the hydraulic lifting platform? Cut off the power first to avoid tragedies such as electric leakage and electric shock)What are the maintenance rules for hydraulic lift machinery? The brakes of each mechanism should be checked frequently and the gap between the brake shoe and the brake wheel should be adjusted to ensure flexibility and reliability. There should be no dirt on the friction surface, and if there is dirt, it must be washed off with gasoline or thinner.System: explosion-proof electronic control system, remote control system, P IC system.

The load of this series of products is divided into . to . tons, and can also be customized according to user requirements, with a load of up to tons.High quality brand,In the construction elevator, the switch box also has leakage protection equipment. Its wires and cables are well insulated, without leakage, and the metal threaded is not rusted, and its damage is close to zero. His steel wire rope should comply with the corresponding configuration requirements, and there is no problem of broken strands and diameter reduction. Of course, the number of broken wires should not exceed the corresponding standard. His pulley movement is very flexible.Looseness occurs: The newly processed and assembled parts of mobile lifts and other aerial work platform equipment have a tendency to geometric shape and matching size. , Coupled with excessive wear and other reasons, it is easy to loosen the originally fastened parts of aerial work platform equipment such as mobile lifts.Frequently check whether the various mechanisms are operating normally and whether there is any noise. If a fault is found,Saint DenisWhere is there a lift for goods, it must be eliminated in time.Saint Denis,Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, the lift also has a lot of safety equipment.The boxes and distribution boxes of the hydraulic lift are always kept clean, and the dust on the electrical equipment is cleaned in time.

Uses: The scissor-type fixed lifting platform is mostly used for the transportation of goods between the height differences of the production line, the loading and unloading of materials, the adjustment of the working height during the assembly of the workpiece, the lifting of parts during the assembly of large equipment, fixed three-dimensional parking and other places.Features of hydraulic lifts: According to the working mode car lifting, hydraulic lifting platform products are divided into crank arm hydraulic lifting machines, scissor hydraulic lifting machines, mast type hydraulic lifts, and straight arm hydraulic lifting machines. The hydraulic lift is a replacement product of the folding arm lift (lifting platform) and the scissor lift (lifting platform). It can be widely used in stations, airports, hotels, post and telecommunications, municipal gardens, garages, cleaning companies, public building facade decoration, decoration or installation and maintenance of power systems, etc. The lift has the advantages of light weight, self-propelled, electric start, simple operation, large working area,Winnie snowGuide rail type lifting cargo elevator, especially the ability to cross obstacles for high-altitude operations and the like.Winnie snow,Hydraulic lifting freight elevator, cargo elevator, is mainly designed for transporting goods, usually accompanied by people. The freight elevator car has the characteristics of long and narrow. A vertical lift powered by an electric motor, fitted with a box-like gondola. Fixed lifting equipment serving specified floors. It has a car that runs between at least two vertical columns of rigid rails. Let's take a look at its daily maintenance skills: Daily maintenance skills for hydraulic lifts The newly installed hydraulic lifts first have a warranty period from the elevator manufacturer (generally -- years).It is best not to cover the aerial work vehicle and park the vehicle outside. If it is windy and rainy, the clothing will repeatedly slap the car paint, especially if the car blows sand on the clothes, it will draw many fine scratches on it. Because it will turn black over time. In addition, when the wind does not directly spray powder or clean the sand on the mechanism, but it should be washed with water, and prevent the sand particles on the paint surface from being scratched by the vacuum cleaner.Ivanava,The water cooling of the hydraulic station is generally tube-type water cooling, and its type selection is based on the heat load to calculate the heat exchange area, while its air-cooled elevator is carried out by using an air cooler, and it is The heat transfer capacity is calculated according to the heat load, and then the type selection calculation is carried out under the condition that the flow rate can be satisfied. Therefore, these two kinds of cooling are not the same, and there is a big difference. Long-term promotion of freight elevator factories and other, Long-term cooperation, mutual benefit and win-win. If you choose the wrong supplier, you will be overwhelmed with all kinds of after-sales troubles in the later stage. Recently, I have seen many netizens report the problem of very loud oil cylinders. Today, the editor will simply popularize the knowledge for everyone.After the goods are transported, clean up the debris on the platform.Hydraulic pump station: special pump station for domestic lifting platform, protection device outside the pump station imported from Italy: organ m type, mesh type, iron plate seal type.

The motor connection is wrong. When the delta connection motor is wrongly connected into a star shape, the motor still runs with full load, and the current flowing through the stator winding will exceed the rated current, and even cause the motor to stop by itself. If it overheats, it will burn out. When the star-connected motor is wrongly connected into a triangle, or the motor with several coil groups connected in series to form a branch circuit is connected in parallel with two branches, it will cause the winding and core to overheat, and in severe cases, the winding will be burned.The motor does not turn: the motor is broken, and the manufacturer has to deal with it.The safety device and application of the guide rail hydraulic lifting platform The use of the guide rail hydraulic lifting platform The guide rail hydraulic lifting platform is a non-scissor hydraulic lifting freight elevator. It is used for goods between different floors of industrial plants, restaurants, restaurants, etc. The low height can be made to -mm. The advantage is that it can be placed directly on the ground without digging pits, reducing engineering construction costs, and there is no need to set up hanging points on the top, which is safe. Reliable; the hydraulic lifting platform adopts hydraulic transmission mode, and can be non-calibrated according to customer needsSeveral types: Motor winding open circuit. When one of the motor windings is disconnected, or one of the parallel branches is disconnected, the three-phase current will be unbalanced and the motor will overheat.Process inspection,System: explosion-proof electronic control system, remote control system P IC system.Before the elevator manufacturer connects the motor to the elevator, please make the keyway of the motor shaft perpendicular to the tightening bolt. In order to ensure uniform force, please screw on the mounting bolts at any diagonal position first, then screw on the other two mounting bolts at diagonal positions, and then tighten the four mounting bolts one by one. Finally, tighten the tension bolts. All tightening bolts need a torque wrench to fix according to the marked fixed torque data and check whether the lift and lifting platform are used.How should we check the construction site of the construction hoist? you know?Use Hydraulic lifts are widely used in various industrial enterprises and production lines such as automobiles containers, mold manufacturing, wood processing, chemical filling, etc., to meet the lifting needs of different operating heights, and can be equipped with various table forms (such as balls, rollers, steering, tilting, with various methods (separate,Winnie snow2 ton lifting cargo elevator, linkage, with the characteristics of stable and accurate lifting, frequent starting, large load capacity, etc., effectively solving the difficulties of various lifting operations in industrial enterprises, so that Production operations freely. The professional elevator factory has advanced technology, strict testing, more affordable prices, and more discounts are in progress, welcome to consult.

Outriggers: mechanical outriggers, hydraulic outriggers, ordinary hand-operated outriggers, pull-out outriggers.Quality Assurance,Secondly, there must be no dirt on the friction surface. If there is dirt, it needs to be washed off with gasoline or thinner; the gear box, gearbox, external gear and other parts of the equipment and the hydraulic oil must be in accordance with the requirements in the table; Correctly maintain the hydraulic guide rail lift. Regularly check whether the wire ropes in each part are broken or loose. If this phenomenon is found, replace them in time. If there is any looseness, it should be tightened in time. The connecting bolts of the equipment should be checked for tightness when the body is under pressure. All connecting shafts should be equipped with cotter pins; check whether each mechanism is operating normally, whether there is noise or failure , to eliminate all faults in a timely manner; when installing, dismantling and adjusting the slewing mechanism of the equipment, it is necessary to pay attention to the parallelism between the reducer and the center line of the gear, and the appropriate meshing gap; conduct a comprehensive inspection of the equipment regularly, whether the wires and cables are If there is damage, whether the motor is overheated,Winnie snowGuide rail type cargo elevator, replace it in time and continue to run after troubleshooting; ensure that the bearings of the motor, each box, distribution box and brushes must be kept clean, and the travel switch points of each safety device must be safe and reliable.When in use the four outriggers should be firmly supported on a solid ground (based on the fact that the walking wheels are about to leave the ground). If necessary, sleepers can be used.What kind of function can be achieved by installing the elevator? Before installation, confirm whether the motor and the elevator are intact, and strictly check whether the dimensions of the parts connected to the motor and the elevator match. Here are the dimensions of the positioning boss of the motor, the input shaft and the groove of the elevator. Fitting tolerances.Winnie snow,The anti-rust work of the aerial work vehicle generally needs to be paid attention to when the aerial work vehicle has not been used for a long time. How should we do anti-corrosion for the body of the aerial work vehicle? This is actually very simple. You don’t need to spend money to go to the repair station for anti-corrosion. As long as our car owners use some materials that they can find at hand it can be realized. At the same time, paying attention to driving habits can ensure that the aerial work vehicle does not rust. Here are a few points that can be used as a reference.The water cooling of the hydraulic station is generally tube-type water cooling, and its type selection is based on the heat load to calculate the heat exchange area while its air-cooled elevator is carried out by using an air cooler, and it is The heat transfer capacity is calculated according to the heat load, and then the type selection calculation is carried out under the condition that the flow rate can be satisfied. Therefore, these two kinds of cooling are not the same, and there is a big difference. Long-term promotion of freight elevator factories and other, Long-term cooperation, mutual benefit and win-win. If you choose the wrong supplier you will be overwhelmed with all kinds of after-sales troubles in the later stage. Recently, I have seen many netizens report the problem of very loud oil cylinders. Today, the editor will simply popularize the knowledge for everyone.The safety device of the guide rail hydraulic lifting platform The mechanical part of the guide rail hydraulic lifting platform mainly includes the hydraulic system and the mechanical device.

The parts such as reduction box, gearbox, external gear and hydraulic oil are all in accordance with the requirements in the table.What kind of function can be achieved by installing the elevator? Before installation,RajibriTwo ton lifting cargo elevator, confirm whether the motor and the elevator are intact, and strictly check whether the dimensions of the parts connected to the motor and the elevator match. Here are the dimensions of the positioning boss of the motor, the input shaft and the groove of the elevator. Fitting tolerances.Rajibri,The seat belt needs to be inspected every six months. The inspection load is kg, and the test time is five minutes. After the test,RajibriElectric cargo elevator, check whether the seat belt is cracked or deformed, and make a record of the experiment. Discontinue use immediately.The water cooling of the hydraulic station is generally tube-type water cooling, and its type selection is based on the heat load to calculate the heat exchange area, while its air-cooled elevator is carried out by using an air cooler, and it is The heat transfer capacity is calculated according to the heat load, and then the type selection calculation is carried out under the condition that the flow rate can be satisfied. Therefore, these two kinds of cooling are not the same, and there is a big difference. Long-term promotion of freight elevator factories and other, Long-term cooperation, mutual benefit and win-win. If you choose the wrong supplier, you will be overwhelmed with all kinds of after-sales troubles in the later stage. Recently I have seen many netizens report the problem of very loud oil cylinders. Today, the editor will simply popularize the knowledge for everyone.Skopje,Safety performance: The lifting structure is made of high-strength manganese steel rectangular tube, with strong stability and high carrying capacity. The maximum lifting height is about meters, and the maximum load is about tons. .After the goods are transported, clean up the debris on the platform.Conscientiously write the special construction plan for installation and construction, and make safety technical disclosures to the installers.

Correct construction elevator site inspection First of all we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission,RajibriProfessional cargo elevator, it can be divided into two types: open type and closed type. Of course, the lift also has a lot of safety equipment.Safety protection when using a mobile lift for high-altitude operations How to use the seat belt correctly: When using the belt, the belt must be tightened, and the waist buckle attachment must be tightened; The seat belt rope must be hooked on the ring of the seat belt rope; it is strictly forbidden to hang the seat belt on unstable or sharp-edged components; it is strictly forbidden to replace the parts on the seat belt; the shape is obviously deformed, or Seat belts that have previously been subjected to a severe impact are strictly prohibited.If the motor of the hydraulic lift is overheated, stop the machine in time and continue running after troubleshooting. The motor bearings must be in good condition.Quality department,The boxes and distribution boxes of the hydraulic lift are always kept clean, stop the machine in time and continue running after troubleshooting. The motor bearings must be in good condition.It is strictly forbidden to switch the electric control switch with wet hands. Many people tend to ignore this detail. Although the safety voltage of the hydraulic lifting platform is below V, if you touch the power supply with your hands, it may cause lifting failure in light cases or electric shock accidents in severe cases.

The price is guaranteed, the service is guaranteed, and it is a large-scale logistics and storage equipment service company directly operated by the manufacturer. Since the fixed lift is a mechanical device, the quality and performance of the product must be good. Do not accept the products of some manufacturers whose quality is not up to standard, so as to avoid some safety hazards in use.Discount,Many customers think that the operating power supply of the hydraulic lifting platform is below the safe voltage of V, and there will be no electric shock. They are wrong. Normally, there will be no electric shock, but if there is improper operation, it will still be very dangerous. So how can we effectively prevent the occurrence of electric shock accidents? Today, the editor will share safety knowledge with you.Function: Convenient unloading, low maintenance cost. It is suitable for various vehicles on the loading and unloading yard and places with relatively heavy traffic. Loading and unloading platform, lifting platform, unloading platform: Anti-slip device: This device is welded by steel plates, which can realize the anti-slip function efficiently and is reliable.After the goods are transported, clean up the debris on the platform.Rajibri,Frequently check the humidity of the aerial work vehicle that is prone to water accumulation. It is inevitable that the aerial work vehicle is driving in rainy and snowy weather, or on muddy roads. The bottom and some gaps and indoor floors are easy to accumulate sludge. If the owner does not clean it in time this will hide the moisture. Therefore, the outer edge of the wheel hub, the corner of the bottom of the trunk, the key hole and the wiper frame and other areas should be checked regularly, and the drainage holes in the door and various parts should be kept unblocked to ensure that the car seat covers, carpets and floors are protected from humidity. Rusty fittings.Pay attention to check whether there are any broken wires and loose strands in the wire ropes of each part. If it exceeds the relevant regulations, it must be replaced immediately. The maintenance of the wire rope should be strictly in accordance with regulations.The boxes and distribution boxes of the hydraulic lift are always kept clean, and the dust on the electrical equipment is cleaned in time.

Check the front page of the oil pipe to check whether the skin of the oil pipe of the hydraulic lifting platform is damaged or cracked, and if so, replace it immediately; secondly, check whether there is any sign of looseness at the connection between the oil pipe and the oil pipe, and if so, tighten it immediately to avoid lifting on the hydraulic lifting platform There is an oil spill in the process,MiddleburgElevating cargo elevator, which leads to accidents; what items need to be checked before using the hydraulic lifting platform? Cut off the power first to avoid tragedies such as electric leakage and electric shock)What kind of function can be achieved by installing the elevator? Before installation, confirm whether the motor and the elevator are intact, and strictly check whether the dimensions of the parts connected to the motor and the elevator match. Here are the dimensions of the positioning boss of the motor, the input shaft and the groove of the elevator. Fitting tolerances.Middleburg,Usually check the connection status of each part, if it is loose, it should be tightened. The tightness of the connecting bolts of the body should be checked when the body is under pressure, and all connecting shafts must have cotter pins and must be fully expanded.What kind of function can be achieved by installing the elevator? Before installation, confirm whether the motor and the elevator are intact, and strictly check whether the dimensions of the parts connected to the motor and the elevator match. Here are the dimensions of the positioning boss of the motor, the input shaft and the groove of the elevator. Fitting tolerances.Gargzdai,It is strictly forbidden to switch the electric control switch with wet hands. Many people tend to ignore this detail. Although the safety voltage of the hydraulic lifting platform is below V, if you touch the power supply with your hands, it may cause lifting failure in light cases, or electric shock accidents in severe cases.Use Hydraulic lifts are widely used in various industrial enterprises and production lines such as automobiles, containers, mold manufacturing, wood processing, chemical filling, etc. to meet the lifting needs of different operating heights, and can be equipped with various table forms (such as balls, rollers, Turntable, steering, tilting, telescopic), with various methods (separate, linkage, explosion-proof), with the characteristics of stable and accurate lifting, frequent starting, large load capacity,MiddleburgGuide rail lifting cargo elevator, etc., effectively solving the difficulties of various lifting operations in industrial enterprises, so that Production operations freely. The professional elevator factory has advanced technology, strict testing, more affordable prices, and more discounts are in progress, welcome to consult.The hydraulic lifting platform can be divided into: four-wheel mobile type, two-wheel traction type, car modified type, car type, auxiliary self-propelled type, and the lifting height ranges from a meter to s meter.

It is strictly forbidden to switch the electric control switch with wet hands. Many people tend to ignore this detail. Although the safety voltage of the hydraulic lifting platform is below V if you touch the power supply with your hands, or electric shock accidents in severe cases.When working at heights it may cause lifting failure in light cases, hang the hook of the self-locking device on the metal ring of the safety belt.Many people think that the strength of the elevator itself is relatively high when using the elevator, so they did not strictly follow the installation method in the manual during the installation process, but they do not know that this will cause increased wear and tear of the parts and inflexible operation, and pay attention to the work The installation precautions corresponding to the environment should not be ignored. Correct installation, use and maintenance of elevators are an important part of ensuring the normal operation of mechanical equipment. Therefore, when you install the elevator, please be sure to strictly follow the installation and use related matters below,Middleburg6-ton cargo elevator, and assemble and use it carefully.demand, the short-circuit current is much larger than the normal operating current, which increases the copper loss of the winding, causing the winding to overheat and even burn out.Conscientiously write the special construction plan for installation and construction, and make safety technical disclosures to the installers.Fixed lift is a kind of transportation equipment that directly lifts and unloads goods from the ground. It is mostly used in places such as goods transportation between height differences in production lines, materials on and off the assembly line, parts lifting during large-scale equipment assembly, is there any relevant rule requirement?Discount,What kind of function can be achieved by installing the elevator? Before installation, confirm whether the motor and the elevator are intact, and strictly check whether the dimensions of the parts connected to the motor and the elevator match. Here are the dimensions of the positioning boss of the motor, the input shaft and the groove of the elevator. Fitting tolerances.The hooks of the seat belts are prohibited from being hung on unstable or moving objects.It is strictly forbidden to switch the electric control switch with wet hands. Many people tend to ignore this detail. Although the safety voltage of the hydraulic lifting platform is below V, if you touch the power supply with your hands it may cause lifting failure in light cases, or electric shock accidents in severe cases.Middleburg,Many people think that the strength of the elevator itself is relatively high when using the elevator, so they did not strictly follow the installation method in the manual during the installation process, but they do not know that this will cause increased wear and tear of the parts and inflexible operation and pay attention to the work The installation precautions corresponding to the environment should not be ignored. Correct installation, use and maintenance of elevators are an important part of ensuring the normal operation of mechanical equipment. Therefore, when you install the elevator, please be sure to strictly follow the installation and use related matters below, hydraulic lifting platform products are divided into crank arm hydraulic lifting machines, mast type hydraulic lifts, and straight arm hydraulic lifting machines. The hydraulic lift is a replacement product of the folding arm lift (lifting platform) and the scissor lift (lifting platform). It can be widely used in stations, docks, airports, hotels, post and telecommunications, municipal gardens, garages, public building facade decoration, decoration or installation and maintenance of power systems, etc. The lift has the advantages of light weight self-propelled, electric start, self-supporting legs, large working area, especially the ability to cross obstacles for high-altitude operations and the like.Pay attention to check whether there are any broken wires and loose strands in the wire ropes of each part. If it exceeds the relevant regulations, it must be replaced immediately. The maintenance of the wire rope should be strictly in accordance with regulations.

What is the new price of a fixed lift? Professionally improve the quality assurance of the freight elevator factory. The preferential activities are in progress, and new and old customers are welcome to come to consult.Always check the connections of the various parts of the hydraulic lift, and tighten them if they are loose. The tightness of the connecting bolts of the body should be checked when the body is under pressure.Hardenbach,Working at heights is a very common thing nowadays, but working at heights also has a certain risk factor. So people invented the hydraulic lifting platform to help people complete high-altitude operations more conveniently. However, people should also pay attention when using the hydraulic lifting platform otherwise it is easy to fail, which may cause serious consequences. So what are the common faults of hydraulic lifting platforms?It is strictly forbidden for personnel to take the freight elevator to go up and down floors and climb.Wobulenzi,HardenbachSmall lifting cargo elevator,The boxes and distribution boxes of the hydraulic lift are always kept clean, and the dust on the electrical equipment is cleaned in time.The use of elevators is not to maintain and overhaul after the equipment fails. It is necessary to maintain the equipment according to the correct maintenance and overhaul, and start with the preparation work to prevent all possible failures and accidents. I hope that the editor can summarize the knowledge points today. Help everyone.Correct construction elevator site inspection First of all, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, the lift also has a lot of safety equipment.

It is best not to cover the aerial work vehicle and park the vehicle outside. If it is windy and rainy, the clothing will repeatedly slap the car paint, especially if the car blows sand on the clothes, it will draw many fine scratches on it. Because it will turn black over time. In addition, when the wind does not directly spray powder or clean the sand on the mechanism, but it should be washed with water, and prevent the sand particles on the paint surface from being scratched by the vacuum cleaner.When in use, the four outriggers should be firmly supported on a solid ground (based on the fact that the walking wheels are about to leave the ground). If necessary, sleepers can be used.Always check the connections of the various parts of the hydraulic lift and tighten them if they are loose. The tightness of the connecting bolts of the body should be checked when the body is under pressure.Where is it,After the goods are transported, clean up the debris on the platform.The design of the hydraulic lifting platform is unreasonable. When the designer designs the cylinder barrel and rod, if there is a problem with the design size and angle, then there will definitely be problems in the later stage. Therefore, it is necessary to confirm the technical strength of the manufacturer when working on a hydraulic lifting platform; what is the problem with the sound of the oil cylinder of the hydraulic lifting platform? Design drawings to make the angle of the oil cylinder is slightly deviated, it will cause the friction between the cylinder barrel and the rod, which will cause the sound; the seal quality of the hydraulic lifting platform is different, and the use of different seals will also affect the sound of the oil cylinder, and the seal with excellent material The continuous friction between the parts and the cylinder wall will cause the sound to be very loud, and long-term wear and tear may scratch the oil cylinder and cause oil leakage, so when the hydraulic lifting platform is used, pay attention to ask the manufacturer what brand and material the seal is used; In some cases of mechanical running-in, it is not ruled out that the above three situations are normal, and there will still be noises. If there is no problem after investigation, then don’t worry. It’s just a running-in problem between mechanical parts. It will disappear naturally.The contact opening and closing of the travel switch of each safety device must be reliable, and the contact arc crater should be polished in time.

Outriggers: mechanical outriggers, hydraulic outriggers, ordinary hand-operated outriggers, pull-out outriggers.Create brilliance, two-wheel traction type, car modified type, car type, auxiliary self-propelled type, and the lifting height ranges from a meter to s meter.Open the package prematurely. Before installing the elevator bearing, do not open the package in advance. This will easily lead to premature pollution of the bearing. These pollutions will cause premature damage to the bearing. In addition, ensure the installation The environment is clean, do not bring iron filings, dust, dust, etc. into the bearings, because even some small dust will affect the running-in between the bearings for a long time,HardenbachCargo elevator, resulting in a decrease in the life of the elevator .Goods should be stacked on the platform and not tilted. When the freight elevator goes up and down beyond the range of the platform, no one should stand around to watch.Hardenbach,The hydraulic lifting platform is widely used in the maintenance of industrial and mining enterprises, municipal construction, and decoration of hotels and hotels, with reliable quality and perfect performance.In the construction elevator, the switch box also has leakage protection equipment. Its wires and cables are well insulated, without leakage, and the metal threaded is not rusted, and its damage is close to zero. His steel wire rope should comply with the corresponding configuration requirements, and there is no problem of broken strands and diameter reduction. Of course, the number of broken wires should not exceed the corresponding standard. His pulley movement is very flexible.Before the elevator manufacturer connects the motor to the elevator please make the keyway of the motor shaft perpendicular to the tightening bolt. In order to ensure uniform force, but do not tighten them tightly, then screw on the other two mounting bolts at diagonal positions, and then tighten the four mounting bolts one by one. Finally, tighten the tension bolts. All tightening bolts need a torque wrench to fix according to the marked fixed torque data and check whether the lift and lifting platform are used.How should we check the construction site of the construction hoist? you know?

It is strictly forbidden for personnel to take the freight elevator to go up and down floors and climb.Before the elevator manufacturer connects the motor to the elevator, please make the keyway of the motor shaft perpendicular to the tightening bolt. In order to ensure uniform force, please screw on the mounting bolts at any diagonal position first but do not tighten them tightly, then screw on the other two mounting bolts at diagonal positions, and then tighten the four mounting bolts one by one. Finally, tighten the tension bolts. All tightening bolts need a torque wrench to fix according to the marked fixed torque data and check whether the lift and lifting platform are used.How should we check the construction site of the construction hoist? you know?Gleevec,Remove and disassemble the descending valve of the hydraulic elevator, blow off the plunger with compressed air, then install it and install it again.Precautions for elevator installation Keep the access road of the external construction elevator smooth and have enough parking space for equipment. When it is necessary to use a steam crane for auxiliary installation, it should be fully considered whether the site environment meets the operating conditions of the steam crane.Masty,Always check all wires and cables for damage. The damaged part should be bandaged and replaced in time.Many customers think that the operating power supply of the hydraulic lifting platform is below the safe voltage of V, and there will be no electric shock. They are wrong. Normally, there will be no electric shock, but if there is improper operation, it will still be very dangerous. So how can we effectively prevent the occurrence of electric shock accidents? Today, the editor will share safety knowledge with you.The use of the hydraulic lifting platform The user can choose the power mode and configuration according to his own scope of use: the power system includes: DC power supply, single-phase or three-phase power supply, and diesel engine.

What kind of function can be achieved by installing the elevator? Before installation, confirm whether the motor and the elevator are intact, and strictly check whether the dimensions of the parts connected to the motor and the elevator match. Here are the dimensions of the positioning boss of the motor, the input shaft and the groove of the elevator. Fitting tolerances.: Small pneumatic or electric rust removal, this is the principle of using air compression to generate friction or electromagnetic effect to generate friction. It can be used to polish and remove rust on the rusty surface of the screw elevator table. It can be used for push rods of precision instruments or for Businesses that need to micro-operate screw jacks.The hydraulic lifting platform can be divided into: four-wheel mobile type, two-wheel traction type, car modified type, car type, auxiliary self-propelled type and the lifting height ranges from a meter to s meter.Direct material,In addition to the fixed mode the elevator also has a vehicle-mounted mobile type. As the name implies, it combines the lifting equipment with the vehicle-mounted system. Such a lifting equipment is very flexible to move, and of course it is more useful. For example There is this kind of lifting equipment in the airport, the scope of operation is not limited to a certain place, and it can be used wherever lifting operations are required. It can be used. For example, when installing outdoor advertisements, the height of some advertisements is relatively high. At this time, mobile lifting equipment can be used to send billboards or staff to the designated height to work. This kind of equipment can also be divided into two types according to the driving mode: hydraulic lifting and electric lifting. The so-called hydraulic lifting is driven by hydraulic oil to reach a specified height. The electric mode is driven by a motor or geared to lift to A certain height but at present, hydraulic lifting platforms are more widely used.Avoid working in an environment. In the event of rain, snow and other weather, the use of the hydraulic lifting platform should be stopped to prevent the occurrence of a short circuit, resulting in electric leakage and electric shock; non-professionals are strictly prohibited from disassembling electrical appliances such as hydraulic lifting platforms. In the event of an accident, you can’t disassemble without permission to eliminate the cause. You must report to the manufacturer for repair in time, inform the phenomenon of the accident, and the manufacturer will guide you to complete the inspection or send someone to repair it; do not disassemble the appliance without permission! Professional elevator factory guarantees quality, guarantees service. Guarantees quality. Your satisfaction is our pursuit! Welcome to inquire.As for the guide rail elevator installed outdoors, it is often exposed to rain and sunlight, so special attention should be paid to regular maintenance and inspection to avoid accidents.

Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course,GleevecWarehouse elevator, the lift also has a lot of safety equipment.Development Curriculum, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, and that the outer flanges of the two are parallel. If the concentricity is inconsistent, it will cause the motor shaft to break or the elevator gear to wear.The hooks of the seat belts are prohibited from being hung on unstable or moving objects.Whether it is used outdoors or indoors, some small problems will inevitably appear after a long period of time. At this time, what we should do is to maintain and maintain the elevator. How to follow the steps correctly It has become a difficult problem, and I will answer it with you.Gleevec,Naturally connect the motor to the lift. When connecting,GleevecChain guide rail lifting cargo elevator, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, it will cause the motor shaft to break or the elevator gear to wear.Naturally connect the motor to the lift. When connecting, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, and that the outer flanges of the two are parallel. If the concentricity is inconsistent, it will cause the motor shaft to break or the elevator gear to wear.In the construction elevator, the switch box also has leakage protection equipment. Its wires and cables are well insulated, without leakage, and its damage is close to zero. His steel wire rope should comply with the corresponding configuration requirements, and there is no problem of broken strands and diameter reduction. Of course, the number of broken wires should not exceed the corresponding standard. His pulley movement is very flexible.

Many customers think that the operating power supply of the hydraulic lifting platform is below the safe voltage of V and there will be no electric shock. They are wrong. Normally, there will be no electric shock, it will still be very dangerous. So how can we effectively prevent the occurrence of electric shock accidents? Today, the editor will share safety knowledge with you.Test the freight elevator every day to see if the freight elevator can operate normally.Vigvano, and uneven table tops. It is recommended to carefully check whether the oil delivery pipe is unblocked.Before the elevator manufacturer connects the motor to the elevator, please make the keyway of the motor shaft perpendicular to the tightening bolt. In order to ensure uniform force, please screw on the mounting bolts at any diagonal position first, but do not tighten them tightly, then screw on the other two mounting bolts at diagonal positions,VigvanoThree ton cargo elevator, and then tighten the four mounting bolts one by one. Finally, tighten the tension bolts. All tightening bolts need a torque wrench to fix according to the marked fixed torque data and check whether the lift and lifting platform are used.How should we check the construction site of the construction hoist? you know?Salerno,Naturally connect the motor to the lift. When connecting, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, and that the outer flanges of the two are parallel. If the concentricity is inconsistent, it will cause the motor shaft to break or the elevator gear to wear.Pay attention to check whether there are any broken wires and loose strands in the wire ropes of each part. If it exceeds the relevant regulations, it must be replaced immediately. The maintenance of the wire rope should be strictly in accordance with regulations.Anti-corrosion measures for the body of aerial work vehicles Pay attention to small scratches. The paint surface of aerial work vehicles is often corroded. In addition to common collisions, scratches, small rocks on the driving tires, there may also be a peeling paint spot, and a small rust will appear after a long time. Because most of these scars are small, they are easy to ignore. Therefore, check regularly, the engine compartment cover and its surroundings, and once found, go to a professional beauty shop for processing.

The parts such as reduction box, gearbox, external gear and hydraulic oil are all in accordance with the requirements in the table.What are the advantages of installing a rail-type elevator freight elevator? The advantages of civil construction are easy to install: no machine room is required above the hoistway, and the top floor can be installed at a height of more than meters. The machine room can be located within a radius of meters of the shaft, occupying an area of ​​only - square meters. The hydraulic elevator is not equipped with a counterweight device, which improves the utilization rate of the hoistway area. The load of the hydraulic elevator and the load-bearing cylinder directly act on the foundation pit, and the strength of the shaft is low, and the shaft with a brick structure or a brick-concrete structure is sufficient.If the motor of the hydraulic lift is overheated stop the machine in time and continue running after troubleshooting. The motor bearings must be in good condition.Variable cost,The daily maintenance of the hydraulic lifting platform in normal use is essential, but even if there is normal maintenance on the equipment, any possible problem cannot be ignored, so in order to ensure that the process of using the hydraulic lifting platform for each operation What aspects do we need to check before operation? Today, the editor will give you a popular science.Safety performance: The lifting structure is made of high-strength manganese steel rectangular tube, and the scissor-type mechanical mechanism is easy to maintain, with strong stability and high carrying capacity. The maximum lifting height is about meters, and the maximum load is about tons. .The parts such as reduction box, gearbox, external gear and hydraulic oil are all in accordance with the requirements in the table.

The last thing to note is that, compared with the lifting platforms in some places, protective fences are generally added on the platforms. Since the lifting platforms are special equipment, so when the personnel ask you if you want to add a guardrail, don't blindly refuse, you must have the 'People's Republic of Special Equipment Manufacturing License' and the 'People's Republic of Special Equipment Installation, Transformation and Maintenance License' to produce, install, and maintain. Therefore, you must ask whether the manufacturer has these two certificates.Customer first,The load of this series of products is divided into . to . tons, and can also be customized according to user requirements, with a load of up to tons.As you all know now, lifts and lifting platforms have been widely used by people in recent years in order to solve the problems we encounter in our daily life. Because aerial work is a high-risk occupation, certain work must be completed with the help of auxiliary tools, so the use of lifts is undoubtedly emerging in the domestic machinery market and has been vigorously developed.Outriggers: mechanical outriggers,VigvanoElevating cargo elevators from first to second floors, hydraulic outriggers, ordinary hand-operated outriggers, pull-out outriggers.Vigvano,The scissor-type fixed lifting platform is a kind of transportation and handling equipment for transporting goods from a certain height to another height. After the operation is completed the platform is level with the ground, does not occupy the ground space, and does not affect the passageway.The safety device and application of the guide rail hydraulic lifting platform The use of the guide rail hydraulic lifting platform The guide rail hydraulic lifting platform is a non-scissor hydraulic lifting freight elevator. It is used for goods between different floors of industrial plants, restaurants, restaurants,VigvanoBody guide rail type cargo elevator, etc. The low height can be made to -mm. The advantage is that it can be placed directly on the ground without digging pits, reducing engineering construction costs and there is no need to set up hanging points on the top, which is safe. Reliable; the hydraulic lifting platform adopts hydraulic transmission mode, and can be non-calibrated according to customer needsSeveral types: Motor winding open circuit. When one of the motor windings is disconnected, or one of the parallel branches is disconnected, the three-phase current will be unbalanced and the motor will overheat.Precautions for elevator installation Keep the access road of the external construction elevator smooth and have enough parking space for equipment. When it is necessary to use a steam crane for auxiliary installation, it should be fully considered whether the site environment meets the operating conditions of the steam crane.

Today, the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.Safety ropes for mobile lifts. Personnel working at heights are always required to hang their safety belts on the safety ropes during mobile operations.Outriggers: mechanical outriggers, hydraulic outriggers, ordinary hand-operated outriggers, pull-out outriggers.Free consultation,Brake operators of various mechanisms on the equipment should regularly check and adjust the gap between the brake shoe and the brake wheel to ensure flexibility and reliability. Long-term promotion of freight elevator factory, old brand, price advantage, quality guaranteed!Frequently check whether the various mechanisms are operating normally and whether there is any noise. If a fault is found, it must be eliminated in time.Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course,ModenaElevating cargo elevators from first to second floors, the lift also has a lot of safety equipment.

Safety performance: The lifting structure is made of high-strength manganese steel rectangular tube, and the scissor-type mechanical mechanism is easy to maintain, with strong stability and high carrying capacity. The maximum lifting height is about meters, and the maximum load is about tons. .target,It is best not to cover the aerial work vehicle and park the vehicle outside. If it is windy and rainy, the clothing will repeatedly slap the car paint, especially if the car blows sand on the clothes, it will draw many fine scratches on it. Because it will turn black over time. In addition, when the wind does not directly spray powder or clean the sand on the mechanism, but it should be washed with water, and prevent the sand particles on the paint surface from being scratched by the vacuum cleaner.Any product always has a running-in period when it is used for the first time, so what should we pay attention to during the running-in period of using the hydraulic lifting platform? Today, the editor will share this topic with you.Fixed lift is a kind of transportation equipment that directly lifts and unloads goods from the ground. It is mostly used in places such as goods transportation between height differences in production lines, materials on and off the assembly line, parts lifting during large-scale equipment assembly,Modena5 ton cargo elevator, and fixed three-dimensional parking. So what is the new price of the fixed lift?Modena,How to effectively prevent electric shock by using a hydraulic lifting platform It is very common to add a leakage protector, and the cost is not high. It is both affordable and safe, and can effectively prevent electric shock.It is strictly forbidden to switch the electric control switch with wet hands. Many people tend to ignore this detail. Although the safety voltage of the hydraulic lifting platform is below V, if you touch the power supply with your hands, it may cause lifting failure in light cases, or electric shock accidents in severe cases.Check the front page of the oil pipe to check whether the skin of the oil pipe of the hydraulic lifting platform is damaged or cracked and if so, replace it immediately; secondly, check whether there is any sign of looseness at the connection between the oil pipe and the oil pipe, and if so, tighten it immediately to avoid lifting on the hydraulic lifting platform There is an oil spill in the process which leads to accidents; what items need to be checked before using the hydraulic lifting platform? Cut off the power first to avoid tragedies such as electric leakage and electric shock)

The hydraulic lifting platform is widely used in the maintenance of industrial and mining enterprises, municipal construction and decoration of hotels and hotels, with reliable quality and perfect performance.Naturally connect the motor to the lift. When connecting, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, it will cause the motor shaft to break or the elevator gear to wear.Stavara,Remove and disassemble the descending valve of the hydraulic elevator, blow off the plunger with compressed air, then install it and install it again.Hydraulic system: mainly oil cylinders, high-strength chrome-plated rods, Japanese NOK seals, self-made external integrated pump stations, oil pipelines, gear pumps, etc. The Japanese NOK seal used in the oil cylinder has good wear resistance, which ensures that the oil cylinder series will not leak oil for a long time. The gear pump pumps the oil in the oil tank into the oil circuit and enters the oil cylinder, thereby driving the top of the rod and raising the equipment; The valve is used to adjust the oil output, the ascending and descending speed,Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, the lift also has a lot of safety equipment.Before using the aerial work platform, it is necessary to confirm whether the outriggers are well supported refer to the level beads on the equipment to judge and debug, and if there is When drying the site and then proceed with the operation; the rollers and slideways confirm whether the roller slideways of the hydraulic lifting platform are dry, an appropriate amount of butter should be added to ensure the smoothness during operation and to avoid head-to-head wear between mechanical parts.After the goods are transported, clean up the debris on the platform.

Knowledge popularization of scissor-type fixed lifting platform Superior performance: equipped with safety devices to prevent overloading of the lifting platform; equipped with protection valves to prevent hydraulic oil pipes from breaking; equipped with emergency descending devices for sudden power failures; Lock safety device.Now you understand how to use the hydraulic lift. It provides our operators with a safe working environment and improves the working efficiency and quality of the lift.Walking: assisted self-propelled, two-wheel traction, self-driving, and car modified.ranking,What kind of function can be achieved by installing the elevator? Before installation, confirm whether the motor and the elevator are intact, and strictly check whether the dimensions of the parts connected to the motor and the elevator match. Here are the dimensions of the positioning boss of the motor, the input shaft and the groove of the elevator. Fitting tolerances.The hydraulic lifting platform is mainly the pressure transmission of hydraulic oil to realize the lifting function. Its scissor mechanical structure makes the lift stable, and the wide operating platform and high carrying capacity make the high-altitude operation wide and suitable for many people work at the same time. It makes high-altitude operations efficient and secure.When the freight elevator breaks down, professionals should be invited to repair it, and the freight elevator cannot be altered without authorization.

Precautions for using guide rail elevators Precautions for using guide rail elevators: It is strictly forbidden to overload, transport flammable and explosive products and other products.Work courses,Ensure good power supply at the installation site, install a separate distribution box, and the leakage switch must meet the requirements for construction elevators when used in the distribution box. If the construction elevator installed is frequency conversion,StavaraGuide rail chain cargo elevator lifting, the leakage switch should be adapted to the frequency converter when selecting the leakage switch .It is necessary to bandage and replace the damaged part in time. The elevator is a kind of hydraulic elevator, also known as the guide rail hydraulic elevator, which is suitable for the transportation of goods higher than buildings, restaurants and hotel floors. Next, Lipusheng Machinery will introduce to you the daily maintenance of the elevator.What is the new price of fixed lifts? Fixed lifts are currently very popular in the market. Due to different manufacturers, different materials, different rated loads, and different brand awareness, the prices are also different. The current price of fixed lifts produced in the domestic market: rated load - tons, height of meters, table size mm *mm, the price is about - yuan; the rated load is - tons, the height is meters, the table size is mm*mm, lift height, table size of each fixed liftDifferent. (Specific bearing capacity and rising height can be customized according to user requirements)Stavara,What is the new price of a fixed lift? Professionally improve the quality assurance of the freight elevator factory. The preferential activities are in progress,Stavara13 meter guide rail type cargo elevator, and new and old customers are welcome to come to consult.Avoid working in an environment. In the event of rain, snow and other weather, the use of the hydraulic lifting platform should be stopped to prevent the occurrence of a short circuit, resulting in electric leakage and electric shock; non-professionals are strictly prohibited from disassembling electrical appliances such as hydraulic lifting platforms. In the event of an accident, you can’t disassemble without permission to eliminate the cause. You must report to the manufacturer for repair in time, inform the phenomenon of the accident, and the manufacturer will guide you to complete the inspection or send someone to repair it; do not disassemble the appliance without permission! Professional elevator factory guarantees quality, guarantees service. Guarantees quality. Your satisfaction is our pursuit! Welcome to inquire.The parts such as reduction box, gearbox, external gear and hydraulic oil are all in accordance with the requirements in the table.

If the motor of the hydraulic lift is overheated, stop the machine in time and continue running after troubleshooting. The motor bearings must be in good condition.What is the new price of a fixed lift? Professionally improve the quality assurance of the freight elevator factory. The preferential activities are in progress,Cross sign4-ton hydraulic lifting cargo elevator, and new and old customers are welcome to come to consult.Cross sign,The sinking of the freight elevator is the phenomenon that after a certain period of time, the platform will drop due to gravity after rising to the designated position. Of course, this kind of problem must be abnormal, so how to solve it? The first is to find the reason, and the following editor summarizes the ultimate solution.The surface of the brushes of each part should be kept clean, and the pressure of the brushes should be adjusted so that the area is not less than %. Professional elevator factory, large quantity favorably, high quality and low price. Fire-resistant-waterproof-high temperature resistant, durable, safe and reliable.Masjed Soleyman,Always check the connections of the various parts of the hydraulic lift, and tighten them if they are loose. The tightness of the connecting bolts of the body should be checked when the body is under pressure.The load of this series of products is divided into . to . tons, and can also be customized according to user requirements, with a load of up to tons.When the freight elevator breaks down, professionals should be invited to repair it, and the freight elevator cannot be altered without authorization.

The parts such as reduction box, gearbox external gear and hydraulic oil are all in accordance with the requirements in the table.Just like the failure of the walking part of the lifting platform, the operator must master the common sense of equipment maintenance and failure, so that he will not appear too flustered when a failure occurs. Generally speaking, the common faults of the walking parts of the lifting platform are divided into: bearing pad burning, axle box bearing burning, traction motor bearing burning, wheel tire relaxation, collapse and other fault problems. Below, I will share with you the solution.Frequently check the humidity of the aerial work vehicle that is prone to water accumulation. It is inevitable that the aerial work vehicle is driving in rainy and snowy weather, this will hide the moisture. Therefore, the outer edge of the wheel hub, the door, the corner of the bottom of the trunk, the key hole and the wiper frame and other areas should be checked regularly,Cross signIndoor cargo elevator, and the drainage holes in the door and various parts should be kept unblocked to ensure that the car seat covers, carpets and floors are protected from humidity. Rusty fittings.management,Use Hydraulic lifts are widely used in various industrial enterprises and production lines such as automobiles, containers mold manufacturing, wood processing, chemical filling, etc., and can be equipped with various table forms (such as balls, rollers Turntable, tilting steering, telescopic), with various methods (separate, linkage, explosion-proof), with the characteristics of stable and accurate lifting, frequent starting, large load capacity, etc., effectively solving the difficulties of various lifting operations in industrial enterprises, so that Production operations freely. The professional elevator factory has advanced technology, strict testing, more affordable prices, and more discounts are in progress, welcome to consult.The hydraulic lifting platform is mainly the pressure transmission of hydraulic oil to realize the lifting function. Its scissor mechanical structure makes the lift stable, and the wide operating platform and high carrying capacity make the high-altitude operation wide and suitable for many people work at the same time. It makes high-altitude operations efficient and secure.Guide rail lift (also known as freight elevator) is a non-scissor hydraulic lifting platform, which is mainly used in industrial plants, restaurants, restaurants, warehouses, docks, workshops and other places that need to move goods vertically between high-rise buildings above the second floor. The low height is especially suitable for sites where the site is not suitable for digging pits. What problems do we need to pay attention to in these places where elevators are used?

Today, the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.index,Always check all wires and cables for damage. The damaged part should be bandaged and replaced in time.Pay attention to heat dissipation when the motor works in a hot environment.What are the maintenance rules for hydraulic lift machinery? The brakes of each mechanism should be checked frequently and the gap between the brake shoe and the brake wheel should be adjusted to ensure flexibility and reliability. There should be no dirt on the friction surface, it must be washed off with gasoline or thinner.Cross sign, if there is a problem with the design size and angle,Cross sign5-ton factory lift cargo elevator, then there will definitely be problems in the later stage. Therefore, it is necessary to confirm the technical strength of the manufacturer when working on a hydraulic lifting platform; what is the problem with the sound of the oil cylinder of the hydraulic lifting platform? Design drawings to make, the angle of the oil cylinder is slightly deviated, it will cause the friction between the cylinder barrel and the rod, which will cause the sound; the seal quality of the hydraulic lifting platform is different and the use of different seals will also affect the sound of the oil cylinder, and the seal with excellent material The continuous friction between the parts and the cylinder wall will cause the sound to be very loud, and long-term wear and tear may scratch the oil cylinder and cause oil leakage, so when the hydraulic lifting platform is used, pay attention to ask the manufacturer what brand and material the seal is used; In some cases of mechanical running-in, and there will still be noises. If there is no problem after investigation, then don’t worry. It’s just a running-in problem between mechanical parts. It will disappear naturally.The scissor-type fixed lifting platform is a kind of transportation and handling equipment for transporting goods from a certain height to another height. After the operation is completed, the platform is level with the ground, does not occupy the ground space, and does not affect the passageway.Test the freight elevator every day to see if the freight elevator can operate normally.

Conscientiously write the special construction plan for installation and construction, and make safety technical disclosures to the installers.Features of hydraulic lifts: According to the working mode, hydraulic lifting platform products are divided into crank arm hydraulic lifting machines, scissor hydraulic lifting machines mast type hydraulic lifts, and straight arm hydraulic lifting machines. The hydraulic lift is a replacement product of the folding arm lift (lifting platform) and the scissor lift (lifting platform). It can be widely used in stations, docks, airports, hotels, post and telecommunications, municipal gardens, garages, cleaning companies, public building facade decoration, decoration or installation and maintenance of power systems, etc. The lift has the advantages of light weight, self-propelled, electric start self-supporting legs, simple operation, large working area, especially the ability to cross obstacles for high-altitude operations and the like.Avorino,When using a helmet, the helmet should be tightened and worn straight, and the strap of the helmet should be tied under the jaw and tightened.How to effectively prevent electric shock by using a hydraulic lifting platform It is very common to add a leakage protector, and the cost is not high. It is both affordable and safe, and can effectively prevent electric shock.Piet Retief,Check the front page of the oil pipe to check whether the skin of the oil pipe of the hydraulic lifting platform is damaged or cracked, and if so, replace it immediately; secondly, check whether there is any sign of looseness at the connection between the oil pipe and the oil pipe, and if so, tighten it immediately to avoid lifting on the hydraulic lifting platform There is an oil spill in the process, which leads to accidents; what items need to be checked before using the hydraulic lifting platform? Cut off the power first to avoid tragedies such as electric leakage and electric shock)Hydraulic pump station: special pump station for domestic lifting platform, protection device outside the pump station imported from Italy: organ m type, mesh type, iron plate seal type.Features of hydraulic lifts: According to the working mode, hydraulic lifting platform products are divided into crank arm hydraulic lifting machines, scissor hydraulic lifting machines, mast type hydraulic lifts, and straight arm hydraulic lifting machines. The hydraulic lift is a replacement product of the folding arm lift (lifting platform) and the scissor lift (lifting platform). It can be widely used in stations, docks, airports,AvorinoElevating cargo elevator Elevating cargo elevator, hotels,AvorinoTwo story cargo elevator, post and telecommunications, municipal gardens, garages, cleaning companies, public building facade decoration, etc. The lift has the advantages of light weight, self-propelled, electric start, self-supporting legs, simple operation, large working area especially the ability to cross obstacles for high-altitude operations and the like.

Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, the lift also has a lot of safety equipment.Remove and disassemble the descending valve of the hydraulic elevator, then install it and install it again.This kind of fixed lifting equipment can also be used in the warehouse. For example, a certain floor in the warehouse needs to be lifted to send goods or personnel into the designated warehouse.Honesty and mutual benefit,Knowledge popularization of scissor-type fixed lifting platform Superior performance: equipped with safety devices to prevent overloading of the lifting platform; equipped with protection valves to prevent hydraulic oil pipes from breaking; equipped with emergency descending devices for sudden power failures; Lock safety device.Hydraulic system: mainly oil cylinders, high-strength chrome-plated rods, Japanese NOK seals, self-made external integrated pump stations, oil pipelines, gear pumps, solenoid valves, etc. The Japanese NOK seal used in the oil cylinder has good wear resistance, which ensures that the oil cylinder series will not leak oil for a long time. The gear pump pumps the oil in the oil tank into the oil circuit and enters the oil cylinder, thereby driving the top of the rod and raising the equipment; The valve is used to adjust the oil output, the ascending and descending speed and contains an emergency descending device to ensure that the guide rail hydraulic lifting platform can descend safely in case of an emergency.What kind of function can be achieved by installing the elevator? Before installation, confirm whether the motor and the elevator are intact,AvorinoProfessional cargo elevator, and strictly check whether the dimensions of the parts connected to the motor and the elevator match. Here are the dimensions of the positioning boss of the motor, the input shaft and the groove of the elevator. Fitting tolerances.

Hydraulic system: mainly oil cylinders, high-strength chrome-plated rods, self-made external integrated pump stations, solenoid valves gear pumps, etc. The Japanese NOK seal used in the oil cylinder has good wear resistance, which ensures that the oil cylinder series will not leak oil for a long time. The gear pump pumps the oil in the oil tank into the oil circuit and enters the oil cylinder, thereby driving the top of the rod and raising the equipment; The valve is used to adjust the oil output, the ascending and descending speed, and contains an emergency descending device to ensure that the guide rail hydraulic lifting platform can descend safely in case of an emergency.Quality department,The hydraulic lifting platform can be divided into: four-wheel mobile type, two-wheel traction type, car modified type, car type, and the lifting height ranges from a meter to s meter.The load capacity of the goods and the tonnage of the goods transported at one time also affect the lifting speed. Reaching the excellent value of the lifting platform for transporting goods is the guarantee of speed. If the goods are too heavy, the speed will be affected. If the goods are too light, the normal delivery time will also be affected.Always check the connections of the various parts of the hydraulic lift, and tighten them if they are loose. The tightness of the connecting bolts of the body should be checked when the body is under pressure.Avorino,When the freight elevator breaks down, professionals should be invited to repair it, and the freight elevator cannot be altered without authorization.Outriggers: mechanical outriggers, hydraulic outriggers, ordinary hand-operated outriggers, pull-out outriggers.Test the freight elevator every day to see if the freight elevator can operate normally.

Many people think that the strength of the elevator itself is relatively high when using the elevator, so they did not strictly follow the installation method in the manual during the installation process, but they do not know that this will cause increased wear and tear of the parts and inflexible operation, and pay attention to the work The installation precautions corresponding to the environment should not be ignored. Correct installation use and maintenance of elevators are an important part of ensuring the normal operation of mechanical equipment. Therefore, when you install the elevator, please be sure to strictly follow the installation and use related matters below, and assemble and use it carefully.The price is guaranteed, the service is guaranteed, and it is a large-scale logistics and storage equipment service company directly operated by the manufacturer. Since the fixed lift is a mechanical device, the quality and performance of the product must be good. Do not accept the products of some manufacturers whose quality is not up to standard, so as to avoid some safety hazards in use.Castration,Mobile lift fault analysis mobileAnalysis of the mobile lift’s poor lift or weak lifting force: the pressure adjustment of the relief valve does not meet the requirements: adjust the pressure to the required value; the internal leakage of the oil cylinder: check or replace the oil cylinder assembly; the reversing valve is locked or internally leaked: check or exchange the valve assembly ;The oil level is too low and the oil inlet filter is blocked: add enough oil and clean the oil filter. Fuel pump defective: check or replace pump.Many customers think that the operating power supply of the hydraulic lifting platform is below the safe voltage of V, and there will be no electric shock. They are wrong. Normally, there will be no electric shock, but if there is improper operation, it will still be very dangerous. So how can we effectively prevent the occurrence of electric shock accidents? Today, the editor will share safety knowledge with you.Horn Ames,Are the water cooling and air cooling of the hydraulic station the same?Precautions for using guide rail elevators Precautions for using guide rail elevators: It is strictly forbidden to overload, transport flammable and explosive products and other products.Always check the connections of the various parts of the hydraulic lift, and tighten them if they are loose. The tightness of the connecting bolts of the body should be checked when the body is under pressure.

Frequently check the humidity of the aerial work vehicle that is prone to water accumulation. It is inevitable that the aerial work vehicle is driving in rainy and snowy weather, or on muddy roads. The bottom and some gaps and indoor floors are easy to accumulate sludge. If the owner does not clean it in time, this will hide the moisture. Therefore, the outer edge of the wheel hub, the door, the corner of the bottom of the trunk, the key hole and the wiper frame and other areas should be checked regularly, and the drainage holes in the door and various parts should be kept unblocked to ensure that the car seat covers, carpets and floors are protected from humidity. Rusty fittings.When working at heights, hang the hook of the self-locking device on the metal ring of the safety belt.When installing, dismantling and adjusting the slewing mechanism, the meshing surface is not less than %, and the meshing clearance is suitable.Development Curriculum,Frequently check the humidity of the aerial work vehicle that is prone to water accumulation. It is inevitable that the aerial work vehicle is driving in rainy and snowy weather, or on muddy roads. The bottom and some gaps and indoor floors are easy to accumulate sludge. If the owner does not clean it in time,CastrationElevating cargo elevator, this will hide the moisture. Therefore the outer edge of the wheel hub, the corner of the bottom of the trunk the door, the key hole and the wiper frame and other areas should be checked regularly, and the drainage holes in the door and various parts should be kept unblocked to ensure that the car seat covers, carpets and floors are protected from humidity. Rusty fittings.Knowledge popularization of scissor-type fixed lifting platform Superior performance: equipped with safety devices to prevent overloading of the lifting platform; equipped with protection valves to prevent hydraulic oil pipes from breaking; equipped with emergency descending devices for sudden power failures; Lock safety device.Unscrew the screw on the dust-proof hole outside the flange of the elevator, adjust the PCS system ring to align the side hole with the dust-proof hole,CastrationSecond floor cargo elevator, remove the motor shaft key.

Safety performance: The lifting structure is made of high-strength manganese steel rectangular tube, and the scissor-type mechanical mechanism is easy to maintain, with strong stability and high carrying capacity. The maximum lifting height is about meters, and the maximum load is about tons. .Professional is king,CastrationHydraulic cargo elevator and lifting cargo elevator,Safety performance: The lifting structure is made of high-strength manganese steel rectangular tube, and the scissor-type mechanical mechanism is easy to maintain, and the maximum load is about tons. .What safety tools are there on mobile lifts Explosion-proof valves: often seen in large hydraulic equipment, especially heavy equipment, the main effect can prevent the oil circuit from bursting or the pressure of the oil circuit is too high to cause problems with the equipment. Regarding small lifts The installation of explosion-proof valves depends on the needs of customers, but large-scale equipment basically needs to be installed.Avoid working in an environment. In the event of rain, snow and other weather, the use of the hydraulic lifting platform should be stopped to prevent the occurrence of a short circuit, resulting in electric leakage and electric shock; non-professionals are strictly prohibited from disassembling electrical appliances such as hydraulic lifting platforms. In the event of an accident, inform the phenomenon of the accident, and the manufacturer will guide you to complete the inspection or send someone to repair it; do not disassemble the appliance without permission! Professional elevator factory guarantees quality, guarantees service. Guarantees quality. Your satisfaction is our pursuit! Welcome to inquire.Castration,Fixed lift is a kind of transportation equipment that directly lifts and unloads goods from the ground. It is mostly used in places such as goods transportation between height differences in production lines, materials on and off the assembly line, parts lifting during large-scale equipment assembly, and fixed three-dimensional parking. So what is the new price of the fixed lift?The hydraulic lifting platform is widely used in the maintenance of industrial and mining enterprises, municipal construction, and decoration of hotels and hotels, with reliable quality and perfect performance.Always check all wires and cables for damage. The damaged part should be bandaged and replaced in time.

The scissor-type fixed lifting platform is a kind of transportation and handling equipment for transporting goods from a certain height to another height. After the operation is completed, does not occupy the ground space, and does not affect the passageway.The hydraulic lifting platform is widely used in the maintenance of industrial and mining enterprises, municipal construction, and decoration of hotels and hotels with reliable quality and perfect performance.Dandong,Open the package prematurely. Before installing the elevator bearing, ensure the installation The environment is clean do not bring iron filings, dust, dust, etc. into the bearings, because even some small dust will affect the running-in between the bearings for a long time, resulting in a decrease in the life of the elevator .The wrong connection of the motor of the elevator When a coil, coil group or one-phase winding is reversed, it will cause a serious imbalance in the three-phase current and cause the winding to overheat.Agdas,Precautions for using guide rail elevators Precautions for using guide rail elevators: It is strictly forbidden to overload, transport flammable and explosive products and other products.The motor connection is wrong. When the delta connection motor is wrongly connected into a star shape, the motor still runs with full load, and the current flowing through the stator winding will exceed the rated current, and even cause the motor to stop by itself. If it overheats, it will burn out. When the star-connected motor is wrongly connected into a triangle, or the motor with several coil groups connected in series to form a branch circuit is connected in parallel with two branches,DandongTwo ton lifting cargo elevator, it will cause the winding and core to overheat, and in severe cases, it can be realized. At the same time, paying attention to driving habits can ensure that the aerial work vehicle does not rust. Here are a few points that can be used as a reference.

Brake operators of various mechanisms on the equipment should regularly check and adjust the gap between the brake shoe and the brake wheel to ensure flexibility and reliability. Long-term promotion of freight elevator factory, old brand, price advantage, quality guaranteed!Check the hydraulic oil quality and oil level. When the lifting platform is raised to the highest level, the hydraulic oil level should be -mm higher than the bottom of the fuel tank. When the oil color of the hydraulic oil becomes dark, the oil is sticky, or there are foreign objects such as gravel in the oil, the hydraulic oil should be replaced in time. Hydraulic System Applications for Lift Tables Check hydraulic and plumbing connections. If the pipe is damaged it should be replaced immediately; if the connection part is loose, tighten the pipe joint.The surface of the brushes of each part should be kept clean, and the pressure of the brushes should be adjusted so that the area is not less than %. Professional elevator factory, large quantity favorably, high quality and low price. Fire-resistant-waterproof-high temperature resistant, durable, safe and reliable.Fair price,If the motor of the hydraulic lift is overheated, stop the machine in time and continue running after troubleshooting. The motor bearings must be in good condition.The motor winding is short-circuited. When a short-circuit fault occurs in the motor winding, the short-circuit current is much larger than the normal operating current, which increases the copper loss of the winding, causing the winding to overheat and even burn out.What types of lifts are there? There are many types of this equipment, for example, it can be divided into fixed lifting devices and vehicle-mounted lifting devices according to the form of movement. The so-called fixed lifting means that it is generally installed in one place and fixed, and then the lifting operation can be carried out. This type of lifting equipment is generally used more on the assembly line. Some large-scale production lines need to move the material when loading materials. Lifting to a certain position, and then putting it into the production line for production, a special lifting device is required to be fixed at a certain position of the production line.

Whether it is used outdoors or indoors,DandongFactory freight elevator lifting, some small problems will inevitably appear after a long period of time. At this time,DandongGuide rail lifting cargo elevator lifting, what we should do is to maintain and maintain the elevator. How to follow the steps correctly It has become a difficult problem, and I will answer it with you.Marketing Department,The wrong connection of the motor of the elevator When a coil, coil group or one-phase winding is reversed, it will cause a serious imbalance in the three-phase current and cause the winding to overheat.The headband of the helmet is adjusted according to the shape of the user's head to prevent the front of the helmet from sliding down and blocking the work line of sight when the user lowers his head to work.Goods should be stacked on the platform and not tilted. When the freight elevator goes up and down beyond the range of the platform, no one should stand around to watch.Dandong,It is strictly forbidden for personnel to take the freight elevator to go up and down floors and climb.Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission it can be divided into two types: open type and closed type. Of course, it is often exposed to rain and sunlight, so special attention should be paid to regular maintenance and inspection to avoid accidents.

The common types of lifts are simply introduced here for you. I hope you can learn more about this product. At present, this product can be said to be sold well in China because many places need to use this product. Products that can be lifted and moved flexibly at the same time. Now companies that specialize in the production of this product combine a large-scale external publicity on the Internet. Friends in need can directly find the corresponding company on the Internet, and then simply learn about the models of these products and Information on performance and price can be purchased directly through the Internet.Uses: The scissor-type fixed lifting platform is mostly used for the transportation of goods between the height differences of the production line, the loading and unloading of materials, the adjustment of the working height during the assembly of the workpiece, the feeding of the installed machine at a high place the lifting of parts during the assembly of large equipment, and the storage and unloading place and Forklifts and other handling vehicles are used for fast loading and unloading of goods car lifting, fixed three-dimensional parking and other places.Salsalsalle,Check whether the self-locking device of the differential protector is normal before working at heights.When installing, dismantling and adjusting the slewing mechanism, care should be taken to ensure that the centerline of the slewing mechanism reducer is parallel to the centerline of the gear, the meshing surface is not less than %, and the meshing clearance is suitable.Bonab,In addition to the fixed mode, the elevator also has a vehicle-mounted mobile type. As the name implies, it combines the lifting equipment with the vehicle-mounted system. Such a lifting equipment is very flexible to move, and of course it is more useful. For example There is this kind of lifting equipment in the airport, and it is also possible to install this kind of equipment in stations or stadiums. Since it can be moved, the scope of operation is not limited to a certain place, and it can be used wherever lifting operations are required. It can be used. For example when installing outdoor advertisements, the height of some advertisements is relatively high. At this time, mobile lifting equipment can be used to send billboards or staff to the designated height to work. This kind of equipment can also be divided into two types according to the driving mode: hydraulic lifting and electric lifting. The so-called hydraulic lifting is driven by hydraulic oil to reach a specified height. The electric mode is driven by a motor or geared to lift to A certain height, but at present, hydraulic lifting platforms are more widely used.Secondly, there must be no dirt on the friction surface. If there is dirt, it needs to be washed off with gasoline or thinner; the gear box, gearbox, external gear and other parts of the equipment and the hydraulic oil must be in accordance with the requirements in the table; Correctly maintain the hydraulic guide rail lift. Regularly check whether the wire ropes in each part are broken or loose. If this phenomenon is found, replace them in time. If there is any looseness, it should be tightened in time. The connecting bolts of the equipment should be checked for tightness when the body is under pressure. All connecting shafts should be equipped with cotter pins; check whether each mechanism is operating normally, whether there is noise or failure ,SalsalsalleElevator enterprise, to eliminate all faults in a timely manner; when installing, dismantling and adjusting the slewing mechanism of the equipment, it is necessary to pay attention to the parallelism between the reducer and the center line of the gear, and the appropriate meshing gap; conduct a comprehensive inspection of the equipment regularly, whether the wires and cables are If there is damage, whether the motor is overheated, replace it in time and continue to run after troubleshooting; ensure that the bearings of the motor, each box, distribution box and brushes must be kept clean, and the travel switch points of each safety device must be safe and reliable.What kind of function can be achieved by installing the elevator? Before installation, confirm whether the motor and the elevator are intact, and strictly check whether the dimensions of the parts connected to the motor and the elevator match. Here are the dimensions of the positioning boss of the motor, the input shaft and the groove of the elevator. Fitting tolerances.

The hydraulic lifting platform is mainly the pressure transmission of hydraulic oil to realize the lifting function. Its scissor mechanical structure makes the lift stable, and the wide operating platform and high carrying capacity make the high-altitude operation wide and suitable for many people work at the same time. It makes high-altitude operations efficient and secure.Relief valve: It can realize the effect of blocking the flow of oil passage and diverting flow. It is often used if the oil pipe bursts,SalsalsalleFixed simple lifting cargo elevator,Hydraulic system: mainly oil cylinders, high-strength chrome-plated rods, self-made external integrated pump stations, oil pipelines, gear pumps, solenoid valves, etc. The Japanese NOK seal used in the oil cylinder has good wear resistance which ensures that the oil cylinder series will not leak oil for a long time. The gear pump pumps the oil in the oil tank into the oil circuit and enters the oil cylinder, thereby driving the top of the rod and raising the equipment; The valve is used to adjust the oil output, the ascending and descending speed, the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.The elevator is a kind of elevator equipment composed of traveling mechanism, hydraulic mechanism, electric mechanism and supporting mechanism. The hydraulic oil is under a certain pressure formed by the vane pump, and enters the lower end of the hydraulic cylinder through the oil filter, throttle valve, hydraulic control check valve, and balance valve, so that the upward movement of the hydraulic cylinder can lift heavy objects , The oil returned from the upper end of the hydraulic cylinder returns to the oil tank through the explosion-proof electromagnetic reversing valve, and the rated pressure relief valve is adjusted, and the pressure gauge reads the pressure gauge.

It is strictly forbidden for personnel to take the freight elevator to go up and down floors and climb.middleman,Before using the aerial work platform, it is necessary to confirm whether the outriggers are well supported, refer to the level beads on the equipment to judge and debug, and then proceed with the operation; the rollers and slideways confirm whether the roller slideways of the hydraulic lifting platform are dry, and if there is When drying the site, an appropriate amount of butter should be added to ensure the smoothness during operation and to avoid head-to-head wear between mechanical parts.Drain all the hydraulic oil in the oil tank, open the oil tank, take out the oil suction filter, clean it, put it back into the oil tank, and install it in its original position. Refill the tank with new oil.What kind of function can be achieved by installing the elevator? Before installation, confirm whether the motor and the elevator are intact, and strictly check whether the dimensions of the parts connected to the motor and the elevator match. Here are the dimensions of the positioning boss of the motor,SalsalsalleGuide rail chain elevator, the input shaft and the groove of the elevator. Fitting tolerances.Salsalsalle,What is the new price of a fixed lift? Professionally improve the quality assurance of the freight elevator factory. The preferential activities are in progress, and new and old customers are welcome to come to consult.Ensure good power supply at the installation site, install a separate distribution box, and the leakage switch must meet the requirements for construction elevators when used in the distribution box. If the construction elevator installed is frequency conversion, the leakage switch should be adapted to the frequency converter when selecting the leakage switch .Hydraulic system: mainly oil cylinders, high-strength chrome-plated rods, Japanese NOK seals, self-made external integrated pump stations, oil pipelines, gear pumps, solenoid valves, thereby driving the top of the rod and raising the equipment; The valve is used to adjust the oil output, the ascending and descending speed, and contains an emergency descending device to ensure that the guide rail hydraulic lifting platform can descend safely in case of an emergency.

The daily maintenance of the hydraulic lifting platform in normal use is essential, but even if there is normal maintenance on the equipment, any possible problem cannot be ignored, so in order to ensure that the process of using the hydraulic lifting platform for each operation What aspects do we need to check before operation? Today, the editor will give you a popular science.The daily maintenance of the hydraulic lifting platform in normal use is essential, but even if there is normal maintenance on the equipment, any possible problem cannot be ignored, so in order to ensure that the process of using the hydraulic lifting platform for each operation What aspects do we need to check before operation? Today, the editor will give you a popular science.san diego ,In the process of developing the guide rail elevator machinery, in order to ensure the use of the heavy platform under safe conditions and maintain compliance with relevant rules and regulations, the heavy platform is specially formulated, and the safety operating procedures are formulated as follows: It must be equipped with qualified and certified lifting equipment.Professional operators who are qualified and certified to work on lifting platforms. Operators working on lifting platforms should wear safety belts. When working in a live area, the car body should be grounded according to regulations. The climbing operation of the heavy platform should be commanded by the operator, and the operator should communicate with the operator of the heavy platform according to the standard signal. The announcement signal should be clear and accurate. The guide rail lift is safe and convenient to use. The guide rail lift usually lifts the lower arm first, the lower arm must be reversed after being raised and lowered at a certain height. Inversion response is slow. Pay attention to whether the distance between the scissor arm and the platform meets the safety requirements of each equipment. For a long time and then the upper arm. During the reversing operation of the lifting platform, we provide all kinds of elevator factories for individuals and enterprises across the country, settle accounts on site, operate with integrity, and have offices in various places for long-term cooperation.Secondly, there must be no dirt on the friction surface. If there is dirt, it needs to be washed off with gasoline or thinner; the gear box, gearbox, external gear and other parts of the equipment and the hydraulic oil must be in accordance with the requirements in the table; Correctly maintain the hydraulic guide rail lift. Regularly check whether the wire ropes in each part are broken or loose. If this phenomenon is found, replace them in time. If there is any looseness, it should be tightened in time. The connecting bolts of the equipment should be checked for tightness when the body is under pressure. All connecting shafts should be equipped with cotter pins; check whether each mechanism is operating normally, whether there is noise or failure , to eliminate all faults in a timely manner; when installing, dismantling and adjusting the slewing mechanism of the equipment, it is necessary to pay attention to the parallelism between the reducer and the center line of the gear, and the appropriate meshing gap; conduct a comprehensive inspection of the equipment regularly, whether the wires and cables are If there is damage, whether the motor is overheated,san diego Chain guide rail lifting cargo elevator, replace it in time and continue to run after troubleshooting; ensure that the bearings of the motor, distribution box and brushes must be kept clean, and the travel switch points of each safety device must be safe and reliable.Hwaseong,The hydraulic lifting platform is widely used in the maintenance of industrial and mining enterprises, and decoration of hotels and hotels, with reliable quality and perfect performance.If the motor of the hydraulic lift is overheated, stop the machine in time and continue running after troubleshooting. The motor bearings must be in good condition.Fixed lift is a kind of transportation equipment that directly lifts and unloads goods from the ground. It is mostly used in places such as goods transportation between height differences in production lines, parts lifting during large-scale equipment assembly, and fixed three-dimensional parking. So what is the new price of the fixed lift?

Always check all wires and cables for damage. The damaged part should be bandaged and replaced in time.The maintenance of the elevator should be refueled regularly: During the use of the elevator, because of the relatively large load, the friction between the various components is also relatively large, especially the elevator chain and the elevator shaft pin. It is necessary to ensure that an appropriate amount of oil is added before each use to ensure It is flexible and not stuck when running work. If the elevator is running once there is a 'squeak' friction sound, it can be basically concluded that the elevator is short of oil, and the work must be stopped immediately to find out the reason and not to force the operation, which is likely to cause unforeseen hidden dangers. Point summary: Maintenance of elevators requires regular refueling which is not allowed.Before using the aerial work platform, it is necessary to confirm whether the outriggers are well supported, refer to the level beads on the equipment to judge and debug,san diego Simple lifting cargo elevator for factory building, and then proceed with the operation; the rollers and slideways confirm whether the roller slideways of the hydraulic lifting platform are dry, and if there is When drying the site, an appropriate amount of butter should be added to ensure the smoothness during operation and to avoid head-to-head wear between mechanical parts.Welcome calls ,This kind of fixed lifting equipment can also be used in the warehouse. For example, a certain floor in the warehouse needs to be lifted to send goods or personnel into the designated warehouse.Hydraulic system: mainly oil cylinders, high-strength chrome-plated rods, Japanese NOK seals, self-made external integrated pump stations, oil pipelines, gear pumps, solenoid valves, etc. The Japanese NOK seal used in the oil cylinder has good wear resistance, which ensures that the oil cylinder series will not leak oil for a long time. The gear pump pumps the oil in the oil tank into the oil circuit and enters the oil cylinder,san diego Two story cargo elevator, thereby driving the top of the rod and raising the equipment; The valve is used to adjust the oil output, the ascending and descending speed, and contains an emergency descending device to ensure that the guide rail hydraulic lifting platform can descend safely in case of an emergency.Knowledge popularization of scissor-type fixed lifting platform Superior performance: equipped with safety devices to prevent overloading of the lifting platform; equipped with protection valves to prevent hydraulic oil pipes from breaking; equipped with emergency descending devices for sudden power failures; Lock safety device.

The load of this series of products is divided into . to . tons, and can also be customized according to user requirements with a load of up to tons.original,Outriggers: mechanical outriggers, hydraulic outriggers, ordinary hand-operated outriggers, pull-out outriggers.The product has solid structure, large carrying capacity, stable lifting simple and convenient installation and maintenance, and is an economical and practical ideal cargo transportation equipment for replacing elevators between low floors. The editor will tell you some common sense about its daily maintenance: when the outdoor elevator is maintained, personnel enter the interior of the elevator to work, and the elevator must be suspended to prevent the elevator from falling suddenly and causing casualties.Prepare the foundation according to the foundation plan, pay attention to the alignment, leveling, and alignment to ensure the level of the foundation and various requirements for use.san diego ,This kind of fixed lifting equipment can also be used in the warehouse. For example, a certain floor in the warehouse needs to be lifted to send goods or personnel into the designated warehouse.The last thing to note is that, compared with the lifting platforms in some places, protective fences are generally added on the platforms. Since the lifting platforms are special equipment, so when the personnel ask you if you want to add a guardrail, and consider whether it is necessary according to the site of use. In addition, you must have the 'People's Republic of Special Equipment Manufacturing License' and the 'People's Republic of Special Equipment Installation, Transformation and Maintenance License' to produce, install, and maintain. Therefore, you must ask whether the manufacturer has these two certificates.It is strictly forbidden to switch the electric control switch with wet hands. Many people tend to ignore this detail. Although the safety voltage of the hydraulic lifting platform is below V, if you touch the power supply with your hands, it may cause lifting failure in light cases, or electric shock accidents in severe cases.

Many customers think that the operating power supply of the hydraulic lifting platform is below the safe voltage of V, and there will be no electric shock. They are wrong. Normally, there will be no electric shock, but if there is improper operation, it will still be very dangerous. So how can we effectively prevent the occurrence of electric shock accidents? Today, the editor will share safety knowledge with you.It is strictly forbidden for personnel to take the freight elevator to go up and down floors and climb.Turku, the safety requirements and specifications of the project site must be complied with.Before wearing the helmet, check whether the helmet shell, hat lining and chinstrap are complete and safe and effective.The price is guaranteed, the service is guaranteed, and it is a large-scale logistics and storage equipment service company directly operated by the manufacturer. Since the fixed lift is a mechanical device, the quality and performance of the product must be good. Do not accept the products of some manufacturers whose quality is not up to standard so as to avoid some safety hazards in use.Machachi,In addition, during installation, it is strictly forbidden to use hammers, etc. to prevent damage to bearings or gears due to excessive axial force or radial force. Be sure to tighten the mounting bolts before tightening the force bolts. Before installation, clean the anti-rust oil on the motor input shaft the positioning boss and the connection parts of the elevator with gasoline or zinc and sodium water. Its purpose is to ensure the tightness of the connection and the flexibility of operation, and to prevent unnecessary wear and tear.Conscientiously write the special construction plan for installation and construction, and make safety technical disclosures to the installers.It is strictly forbidden to switch the electric control switch with wet hands. Many people tend to ignore this detail. Although the safety voltage of the hydraulic lifting platform is below V, if you touch the power supply with your hands, it may cause lifting failure in light cases, or electric shock accidents in severe cases.

Always check all wires and cables for damage. The damaged part should be bandaged and replaced in time.The downward movement of the hydraulic cylinder. The hydraulic oil enters the upper end of the hydraulic cylinder through the explosion-proof electromagnetic directional valve, and the oil returned from the lower end of the hydraulic cylinder returns to the oil tank through the balance valve, hydraulic control check valve,TurkuFixed hydraulic lifting cargo elevator,Turku5-ton factory lift cargo elevator, throttle valve, and explosion-proof electromagnetic directional valve. In order to make the weight drop smoothly and the brake safe and reliable, a balance valve is installed on the oil return line to balance the circuit and maintain the pressure so that the descending speed is not affected by the weight, and the flow rate and lifting speed are adjusted by the throttle valve. In order to make the brake safe and reliable,TurkuProfessional cargo elevator, and prevent accidents, that is, a hydraulic lock, is added to ensure that it can lock itself safely when the hydraulic pipeline bursts accidentally. An overload sound-activated alarm is installed to distinguish overload or equipment failure. Specializing in freight elevator factory, old brand, guaranteed quality!It is strictly forbidden to switch the electric control switch with wet hands. Many people tend to ignore this detail. Although the safety voltage of the hydraulic lifting platform is below V, if you touch the power supply with your hands, it may cause lifting failure in light cases, or electric shock accidents in severe cases.reform,The daily maintenance of the hydraulic lifting platform in normal use is essential, but even if there is normal maintenance on the equipment, any possible problem cannot be ignored, so in order to ensure that the process of using the hydraulic lifting platform for each operation What aspects do we need to check before operation? Today, the editor will give you a popular science.Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, the lift also has a lot of safety equipment.The common types of lifts are simply introduced here for you. I hope you can learn more about this product. At present, this product can be said to be sold well in China, because many places need to use this product. Products that can be lifted and moved flexibly at the same time. Now companies that specialize in the production of this product combine a large-scale external publicity on the Internet. Friends in need can directly find the corresponding company on the Internet, and then simply learn about the models of these products and Information on performance and price can be purchased directly through the Internet.

Today, the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.quality index, and the scissor-type mechanical mechanism is easy to maintain, with strong stability and high carrying capacity. The maximum lifting height is about meters, and the maximum load is about tons. .The second is that steel will have obvious effects of thermal expansion and cold contraction at low temperatures. Although this property of steel will be taken into account when designing and manufacturing hydraulic lifts after all, the environment is different. Under low conditions, steel will appear. Some unstable performances, such as increased hardness, decreased toughness, it is necessary to pay more attention to the maintenance of equipment to keep the key parts in order to avoid dry grinding.What is the new price of fixed lifts? Fixed lifts are currently very popular in the market. Due to different manufacturers, different materials, different rated loads, and different brand awareness, the prices are also different. The current price of fixed lifts produced in the domestic market: rated load - tons, height of meters, table size mm *mm, the price is about - yuan; the rated load is - tons, the height is meters, the table size is mm*mm, the price is about yuan. Rated load, lift height, table size of each fixed liftDifferent. (Specific bearing capacity and rising height can be customized according to user requirements)Turku,Ensure good power supply at the installation site, install a separate distribution box, and the leakage switch must meet the requirements for construction elevators when used in the distribution box. If the construction elevator installed is frequency conversion the leakage switch should be adapted to the frequency converter when selecting the leakage switch .The anti-rust work of the aerial work vehicle generally needs to be paid attention to when the aerial work vehicle has not been used for a long time. How should we do anti-corrosion for the body of the aerial work vehicle? This is actually very simple. You don’t need to spend money to go to the repair station for anti-corrosion. As long as our car owners use some materials that they can find at hand, it can be realized. At the same time, paying attention to driving habits can ensure that the aerial work vehicle does not rust. Here are a few points that can be used as a reference.Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, the lift also has a lot of safety equipment.