Inspection before installation: Check the specification,Tiru gilapaliVertical centrifugal slurry pump,Tiru gilapaliWater well pipeline pump, size and quality of thick and thin accessories.　　Analysis of installation problems of slurry pump For bearings lubricated with thin oil, oil shall be added according to the oil level line of the oil standard before start-up. Add (HL hydraulic oil in winter and (hl hydraulic oil in summer. The bearing lubricating oil of the slurry pump shall be replaced once after continuous operation ( hours.Tiru gilapali,　　Actually, you don&#;t have to worry about this. First of all, stainless steel has very strong anti-corrosion ability compared with products that are easy to rust. When many friends buy stainless steel deep well pumps, their manufacturers will apply a thin anti-corrosion coating on the outer layer of the equipment according to the needs of consumers. as　　Submersible slurry pump In addition, which also requires some time og quantity when switching on and off, so in fact, it can be adjusted to a certain extent during use. The submersible slurry pump needs to use a line when in useCambridge ,　　It is longer and saves production cost. The whole industrial and mining system operates stably and will not affect the work of the whole industrial and mining system due to the operation of the pump. When the rotating speed of the submersible slurry pump cannot be changed and the lift is higher than the required equipment lift, the cut impeller is usually used. The cut is　　 The difference between the vertical slurry pump and the submersible slurry pump The working position of the vertical slurry pump is different. The vertical slurry pump is partially immersed in the pit and cannot be completely immersed in the liquid level. The submersible slurry pump can be completely immersed (including the motor part) below the liquid level; Use of motor for vertical slurry pump　　The supply of shaft seal water must be ensured. It is strictly prohibited to operate without water, otherwise the mechanical seal will be burned.

　　 Then unscrew the nut at the front end of the pump shaft, remove the cover plate, and press out the middle impeller and water seal.　　In terms of performance parameters, optional flow range: - (m/h), lift range: - (m), power range: .- (kw), caliber range: - (mm).　　Although the shaft seal occupies a small position in the pump, the normal operation of the pump is closely related to the shaft seal.Where can I find it?,　　 When starting the slurry pump, the outlet gate valve shall be (closed or slightly opened by /. Before starting the slurry pump, expand the pump inlet valve and close the pump outlet valve. Then start the pump. After the pump is started slowly start the pump outlet valve. The size and speed of opening the pump outlet valve should be based on the fact that the pump does not vibrate and the motor　　When the submersible slurry pump works, the suction pipe needs to be placed in water, and the pump needs to be started. Due to special structural requirements, when the slurry pump motor is submerged in the water the slurry pump and submerged slurry circulating pump need to be placed above the water surface, so they need to be fixed otherwise the motor will fall into the water　　Water pump After understanding the cause of insufficient liquid supply, we can solve the problem: First, we need to check whether the liquid level of the circulating liquid storage tank needs to add media to it.

　　The application of pumps involves all aspects of work and production, and the types of pumps are also diverse. Some of the same pump have several names, and some of the names are very similar, which makes it difficult to distinguish. Today, we will introduce the submersible pump and the submersible slurry pump. Is there any difference between the twomanufacturer,Tiru gilapaliCarbon steel explosion-proof pipeline pump,　　Do not exceed the rated current.　　Transmission type: direct drive, parallel belt drive, upper and lower belt drive, CV vertical belt drive, etc. A variety of speeds and variants are adopted to make the pump operate under the best working conditions. It has long service life and high operation efficiency, and can meet many kinds of harsh transportation conditions.　　It is an auxiliary means of on-site monitoring. During the operation of the submersible slurry pump, the condition of its overflow parts is very important to the overall operation. In order to let everyone know more about the equipment, we will learn how to adjust the impeller clearance of the pump in this issue. I hope it will help you.Tiru gilapali,　　When this type of pump is used at ordinary times, the pump and motor operate in a coaxial whole. When it runs, the motor shaft will drive the impeller of the pump to rotate, and then at this time, the rotating force can be brought to the medium, so that　　At present, mechanical seals occupy an increasing share in the slurry pump seal market.　　The water pump is not only the water supply for the city, but also the household water purifier used in our home. There is a with pump equipment to help us purify water. In any way, it can be divided into many types, each of which has different sizes, many people believe that