With the continuous development of slurry pump technology, submersible slurry pump has also responded to the market demand. At the same time, this type of pump is especially suitable for the depth where the vertical slurry pump cannot operate. Pay attention when using the equipment. The submersible slurry pump can operate if its depth is less than m, but it exceeds　　Let the medium containing some solid particles generate a certain flow rate,IsmailSubmersible non clogging sewage pump,IsmailPipeline pump, so that the equipment can drive the solid to flow when it is in use, so that the slurry can be transported. In terms of the principle of the submersible slurry pump, it is actually quite simpleIsmail,　　It will also be higher but there is no specific conversion standard. Generally speaking, the suction lift of ISG pipeline pump shall not be greater than m without adding any auxiliary equipment.　　Rate.Serendah,　　In addition to the main impeller inside the equipment, a set of impeller for mixing will be added at the bottom of the equipment, so that some mortar slowly settled inside the equipment can be mixed with water to become a flowing medium, so that the equipment can be used without its　　 When starting the slurry pump, the outlet gate valve shall be (closed or slightly opened by /. Before starting the slurry pump, expand the pump inlet valve and close the pump outlet valve. Then start the pump. After the pump is started, slowly start the pump outlet valve. The size and speed of opening the pump outlet valve should be based on the fact that the pump does not vibrate and the motor　　Many people do not know much about the packing and sealing of equipment because of the equipment of mass and energy. Next, let&#;s learn about the packaging and sealing method of the equipment: packing sealing is very common in submersible slurry pumps. This method has good sealing performance, is easy to use, and effectively reduces the wear of the host and anti vibration kinetic energy

　　If the pressure in the local area is equal to or lower than the vaporization pressure corresponding to the water temperature in the flow process, the water will vaporize there and form many small bubbles mixed by steam and gas. The cavitation phenomenon is due to the bubble action when these small bubbles flow from the low-pressure area to the high-pressure area in the water pump,　　Installation method: coupling can be used for direct connection, or belt pulley can be used for connection with belt.　　This phenomenon shows that the failure of the pump is not only a material problem, but also reminds the pump designers and producers that in addition to good working conditions, the pump should also have good corrosion resistance, high reliability and long service life. The pump shall be designed in addition to the conventional design method of fluid mechanicsdiscount　　 First of all, we need to know that submersible pumps generally operate in water. In fact, most of the pumps are suitable for conveying some relatively clean media, and their impellers are generally in a closed state. However, one of the media conveyed by sewage pumps may　　Water pump is a kind of machinery that pumps energy liquid. It is a machine that converts the mechanical energy of the prime mover into the potential energy of the pumped liquid. Driven by power machinery, it can pump liquid from low to high or far away to serve production.　　The high-efficiency slurry pump has three characteristics: first,　　The two have certain commonalities. They are both submersible. As the name suggests, the pump is in an invasive state when running. The submersible slurry pump is a kind of submersible pump, but generally speaking people often say that the submersible pump refers to the clean water pump, such as the submersible pump for domestic water and farmland irrigation and pumping　　 There is no cavitation damage and water diversion. In particular, the latter point brings great convenience to operators.　　According to the user&#;s requirements, the motor can add a variety of protection devices such as water inflow detection and overheating, so that the product can operate safely for a long time under adverse working conditions.Ismail,　　 if the removed gasket is seriously damaged,IsmailISG single stage vertical pipeline pump, a new gasket shall be replaced. The removed parts shall be cleaned with kerosene before assembly.　　 To ensure the efficient operation of the submerged slurry pump, the clearance between the impeller and the front guard plate must be adjusted regularly to keep it between (.-mm). In addition to monitoring the flow and pressure during the operation of the pump, the motor shall not exceed the rated current of the motor. Monitor oil seal and bearing at any time　　When the water pump is driven by electricity or diesel engine, its impeller (like an electric fan) rotates wildly, thus forming a vacuum in the impeller. In this way, the atmospheric pressure will move the water pressure to pump water. In fact