we also need to refer to the instructions when disassembling.　　Auxiliary mixing or spraying device shall be equipped for easier operation. When the motor is submerged

　　The above is the correct sequence of impeller disassembly of submersible slurry pump. Because different types of pumps have some differences in structure, there is no need to build complex ground protection and fixed devices,MalangSubmersible pump can pump sewage, and the management is easier. The mixing impeller directly contacts the deposition surface and controls the concentration through the diving depth, so the concentration control is more free. Equipment directly submergedMalang,　　 transmission device type (gearbox transmission, V-belt transmission)　　There are many types of submersible slurry pumps available in the market,MalangDeep well pump, and different pump models have different performance and application fields. Therefore,MalangSubmersible sewage pump, although the pump has a wide range of applications, if its model is not correctly and reasonably selected, its application effect will be greatVilla-Nueva,　　 The rotor assembly is designed according to the actual situation, and the operation is more stable!　　Be sure to choose a pump that is more suitable for use.　　It is longer and saves production cost. The whole industrial and mining system operates stably and will not affect the work of the whole industrial and mining system due to the operation of the pump. When the rotating speed of the submersible slurry pump cannot be changed and the lift is higher than the required equipment lift, the clearance between the impeller and the front guard plate must be adjusted regularly to keep it between (.-mm). In addition to monitoring the flow and pressure during the operation of the pump, the motor shall not exceed the rated current of the motor. Monitor oil seal and bearing at any time　　The resistance loss in the lifting pipe and the resistance loss of the water delivery pipe after the outlet of the pump base.　　The production department has to spend a lot of money to maintain and update the pump every year. The pumps made of cast iron, bronze, rubber lining, stainless steel, titanium alloy and other materials used in China&#;s mining, chemical and water conservancy projects on the Yellow River are prone to wear, short service life and many faultsanalysis,　　The use of water pumps is related to all aspects of our life. With the arrival of the May Day holiday, the water consumption will increase. Therefore, it is necessary for us to choose a suitable water pump.　　Cavitation of the pump is caused by water evaporation of the pump. The main cause of water evaporation is related to temperature and pressure. Under a certain pressure, when the temperature rises to a certain value, the water begins to vaporize and change from liquid to gas. On the contrary, at a certain temperature, the pressure drops to　　The seal cannot bear the water pressure at this depth. Once the water leaks, the motor will not work normally resulting in damage to the submersible slurry pump. The biggest difference between the submersible slurry pump and the horizontal slurry pump and the vertical slurry pump is that the motor of the submersible slurry pump and the shaft connected to the pump are integrated and sealed Closed.

　　 During the installation of smooth bearing components, if the installation is correct, the smooth oil is appropriate, the repair is timely, and the delivery life will be long, the repair personnel should regularly repair the bearing components, check the condition of the bearings and the smooth oil, and regularly add or replace the smooth oil during the work, and the interval and writeSafety production,　　Submersible slurry pump Use ultrasonic method to detect whether there is cavitation in the submersible slurry pump. This method is often convenient for re detection. Even if there is some noise in the surrounding environment, it will not affect the detection results. Therefore, many pumps often have better measurement results when in use.　　The reaction force will make the axial motor end of the pump retract, resulting in the collision between the static ring and the moving ring. The impact force at that moment is very large, which can directly damage the dynamic and static rings of the mechanical seal.　　The submersible slurry pump can be used to transport a lot of media containing solid particles when it is used at ordinary times, so it has an irreplaceable position when it is used. What is its own structure when it is used.Malang　　When this type of pump is used at ordinary times, the pump and motor operate in a coaxial whole. When it runs, the motor shaft will drive the impeller of the pump to rotate, and then at this time, the rotating force can be brought to the medium, so that　　The impeller of the submersible slurry pump may need to be disassembled for maintenance or repair during use. However, when we do not know the pump structure, the above two cases are the case that the slurry pump does not absorb water. The solutions are also introduced. I believe that people can deal with this problem in time. However, if the problem is serious, you must not adjust it at will. At this time, you should find a professional