The development of submersible slurry pump is to adapt to increasingly complex working conditions,TarnLong shaft submerged slurry pump, facilitate users to use, and its use mode is more flexible. And it fills a part of the gap in the application of slurry pump. When the submergence depth is deep and there is no better slurry outlet, that is,TarnWater well pipeline pump, in the traditional slurry pump　　If the water leakage is serious, the broken pipe shall be dismantled and replaced. Lower the lift and press the nozzle of the water pump into the water for .m.Tarn,　　In addition to conventional accessories, ordinary long shaft pumps can also manufacture deep well pumps with different al characteristics according to the special requirements of customers. If it is required to improve the sealing performance of the pump seat packing, the packing sealing can be changed into a mechanical sealing device. If there is backpressure water at the wellhead,TarnSewage pump diving, a sealed pump seat can be used. If required in none　　Work, no noise and vibration,　　Do not exceed the rated current.　　 repair and level the welding part of the submersible slurry pump with a file, the broken pipe shall be dismantled and replaced. Lower the lift and press the nozzle of the water pump into the water for .m.

　　The submersible slurry pump is a kind of submersible pump which is connected with the motor and works underwater at the same time. In addition, compared with horizontal slurry pump and vertical slurry pump, submersible slurry pump has the great advantage of flexibility and convenience and is more suitable for various working conditions. The important technical points of submersible slurry pump are its motor and　　 Check the surrounding environment: when the ambient temperature is higher than ℃, the temperature of the air inlet will rise resulting in overheating of the motor. Try to improve the working environment. Such as setting up shade sheds for shading.　　 fold the three layers in half with self-adhesive butyl tape and gradually extend to the outside of the core. When winding, the tape shall be stretched twice, and then the three layers shall be folded in half with PVC tape to ensure that the winding part is not less than mm, and the positions of the three joints shall be staggered for a certain distance in order to prevent short circuit.Trustworthy,　　When using the sand pump, be sure to pay attention to the steering divergence between the motor and the pump. The sand pump has an arrow on the pump to mark the main steering. After the power supply is connected, run the pump without load. Check whether the motor operates normally. During operation be careful not to exceed the bearing on the pump support to avoid　　The seal cannot bear the water pressure at this depth. Once the water leaks, the motor will not work normally, resulting in damage to the submersible slurry pump. The biggest difference between the submersible slurry pump and the horizontal slurry pump and the vertical slurry pump is that the motor of the submersible slurry pump and the shaft connected to the pump are integrated and sealed Closed.　　About %), and motor power p=i × U indicates that high power and current will increase.

　　 The submersible slurry pump usually relies on water cooling to dissipate heat. If the motor leaks out of the water without water cooling, the motor temperature will rise,　　It is longer and saves production cost. The whole industrial and mining system operates stably and will not affect the work of the whole industrial and mining system due to the operation of the pump. When the rotating speed of the submersible slurry pump cannot be changed and the lift is higher than the required equipment lift, the cut impeller is usually used. The cut is　　 After the electric pump has been used for many times, it is necessary to put the electric pump into clean water and run it for several minutes to prevent sediment in the pump and ensure the cleanness of the electric pump.　　For example, it has a great impact on the impeller of the equipment itself. So how to detect whether the equipment has cavitation during use?Tarn,　　 The fan speed of the water pump is too low, and the air pressure and air volume are relatively small, so the heat cannot be dissipated.　　Yes, such mechanical faults will cause the stator winding of the pump to be burnt out.　　As a submersible slurry pump widely used in many fields, it has the advantages of simple structure, convenient disassembly and maintenance, and convenient installation and use. The change of the sealing structure of the pump avoids the direct damage to the bearing after the mechanical seal is damaged, and the service life of the bearing has also been greatly changed.