The of descending axial force can be used for slurry transportation in power plants, which is mostly used to transport flammable and the leakage probability does not exceed drops /min, explosive, toxic, strong corrosive and valuable liquids or materials with high temperature, high pressure and low temperature.　　When using the submersible slurry pump, we should do a good job in all aspects of commissioning and precautions. We also need to do a good job in protecting the equipment parts and some parts of the motor. Only in this way can we avoid the impact of water and other impurities entering the motorAmritsar,　　If the flow exceeds QD, cavitation and vibration will occur, which will seriously affect the service life of the pump. Therefore, the pump head shall not be too conservative when selecting the pump. It shall be as close to the actual head of the pipeline as possible. Generally speaking, it shall not exceed times of the actual head of the pipeline.　　 the water pipe shall be short, and the cavitation allowance of the device shall be greater than that of the pump. It is recommended to use the reverse charging installation method when transporting residues with high weight concentration.Hovd,AmritsarPipeline pump,　　After understanding the working principle of the submersible slurry pump, we will also know that those parts are prone to wear during normal use. In this way, we can carry out targeted anti-corrosion and wear-resistant treatment on these parts during optimization, so as to improve the integrity of the equipment and　　 There is also a vibration method to measure the vibration frequency of the pump, and the measurement is relatively simple. However, when using one method, there are other vibration sources that will affect the measurement results, so it is actually the main　　The submersible slurry pump may be blocked when it is used at ordinary times. In particular, some equipment is frequently used at ordinary times, but the maintenance work is not done well when it is used, so it will be blocked after being used for a period of time

　　Analysis of installation problems of slurry pump For bearings lubricated with thin oil, oil shall be added according to the oil level line of the oil standard before start-up. Add (HL hydraulic oil in winter and (hl hydraulic oil in summer. The bearing lubricating oil of the slurry pump shall be replaced once after continuous operation ( hours.　　Dynamic water level: after the pump operates normally, the water inflow in the pool and the pumping capacity of the deep well pump reach an equilibrium point, and the water level at this time is called dynamic water level.　　 Dust and oil stains on the motor reduce the heat dissipation capacity of the equipment and cause the equipment temperature to rise.A complete range of products,　　All kinds of newly designed mechanical seals of submersible slurry pumps contribute greatly to the growth of market share.　　It will burn out. If there is a heating problem in use, you can refer to the following reasons.　　The above is about how to replace the water seal of Boshan submersible slurry pump. In addition to the water seal,AmritsarWater well pipeline pump, other parts of the pump also need to be replaced in time when they are damaged. Moreover, some parts of the pump are relatively easy to be damaged, so we need to replace them regularly during use　　Check whether it needs to be replaced.

　　 If the impeller of the pump is damaged after a long time of use, it will also lead to insufficient liquid supply for the pump.where,　　Submersible slurry pump is a kind of pump used in mines. Do you know the effect and form of its shaft seal? Let&#;s have a look.　　If it can be started and operated with lubricating water, self-lubricating bearings can be used at the support, or other types of bearings (such as polymer bearings) can be used according to the design or contract requirements.　　The other mechanical seal is a split seal,AmritsarBaigang deep well pump, which can be replaced without disassembling the slurry pump.Amritsar,　　The two have certain commonalities. They are both submersible. As the name suggests, the pump is in an invasive state when running. The submersible slurry pump is a kind of submersible pump, people often say that the submersible pump refers to the clean water pump, such as the submersible pump for domestic water and farmland irrigation and pumping　　The water slurry pump is a widely used equipment. Many people are interested in the water diversion and exhaust method of the slurry pump equipment. Now let&#;s talk about the water diversion and exhaust method of the submersible slurry pump: the submersible slurry pump needs to pump out the water to form a vacuum and then supply water,　　Submersible slurry pumps are mainly used in mining, metallurgy, coal, environmental protection electric power and other industries to transport corrosive solid particle slurry. For example, in the field of chemical industry, corrosive mixed pastes of chemical crystals are transported. Electric ash removal, coal washing plant slurry transportation, etc. Submersible slurry pump blade