Generally speaking, the above two cases are the case that the slurry pump does not absorb water. The solutions are also introduced. I believe that people can deal with this problem in time. However,QaxCentrifugal slurry pump, if the problem is serious you must not adjust it at will. At this time, you should find a professional　　Will be scrapped. In addition, since the length of the long shaft is generally fixed, the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. It is normal to use the equipment for a long time, for example,QaxSmall deep well pump, when the submersible slurry pump is used at ordinary times, air holes usually appearQax,　　For example the lubrication method, the number of impellers, the number of bolts and other small details determine that these slurry pumps are not used.　　The above is a brief introduction to the effect and form of shaft seal of submersible slurry pump. Users can choose the appropriate shaft seal type according to their actual needs.Vavoua,　　 Next, it is necessary to check the water seal. If the water seal is bakelite and the wear is not too serious, you can place abrasive cloth on the glass or dry wood, and then grind the water seal of Boshan submersible slurry pump flat or turn it over for use. However, if the thrust rubber water seal is used, when　　 Prepare tools and materials: a set of metric box / open-end wrench, bearing puller (commonly known as triangle puller), outside micrometer, caliper, feeler gauge, copper bar, screwdriver with handle, hammer, V-shaped irons of the same specification, clean kerosene, oil basin, cotton yarn,QaxVertical slurry pump, etc.　　 If there is abnormal sound inside the slurry pump and there is no water, it is likely that the equipment may have air infiltrating into it when absorbing water, and then at the same time, the impeller is damaged or the impeller is damaged

　　In fact, when the submersible slurry pump is blocked during use, it will not only have a certain impact on the working efficiency of the equipment during operation, but also cause serious damage to the equipment itself so it is also a reminder that we are using it too　　 No maintenance: if it is not used continuously after startup, the submersible pump will rust and cannot be started. If it is not used for a long time, industrial pumps have also increased in recent years.Welcome to inquire summer is the peak sales season. In addition to agricultural applications,　　The above four methods can be used to detect whether the submersible slurry pump has cavitation, because if the equipment is in use, it will have a great impact on the operating efficiency. Even if the cavitation time is long, it will also have a certain impact on other parts of the equipment. Sometimes submersible slurry pump　　The hardened mud layer collapses after softening, avoiding the phenomenon of burying the pump during use.　　With the continuous development of slurry pump technology, submersible slurry pump appears in response to market demand. It is especially suitable for the depth at which the vertical slurry pump cannot operate. The underwater part of the vertical slurry pump is generally not more than m, and of course it can be more than. For example, the maximum design depth of our company&#;s underwater slurry pump can reach m, but such underwater depth is not the best operating depth of this kind of pump, so it will lead to the unreliability of the operation of the vertical slurry pump from time to time.

　　Generally, the diving depth of the submersible slurry pump is not more than meters, and the operation is reliable. Why not more than meters? This is the crucial technical point of the submersible slurry pump, because the current sealing technology in China is more than meters, not because the slurry pump has a problem, but becauseThe cost is reasonable,　　Occurrence of personal injury accident. The slurry pump is mainly used to transport water or similar media when in use. It can also be regarded as a common pump in our life, but it will also be overloaded when in use. Let&#;s have a look today　　The motor burns out the winding due to heat dissipation. The water pump shall be lifted and lowered at any time with the change of water level in the well. In case of water reduction or interruption, the cause shall be found out immediately or the pump shall be shut down for inspection. The cable shall not rub against the shaft wall to prevent the well water from penetrating into the motor along the cable core after the cable is worn.　　The first stage impeller of the pump is disassembled; It is also necessary to screw down the connecting nut between the water absorption section and the bearing body and the bolt on the bearing pressure connection, so that it is convenient for us to disassemble the bearing parts; When the shaft is pulled out from the suction section, the fixing nut on the shaft shall beQax,　　 Then unscrew the nut at the front end of the pump shaft, remove the cover plate, and press out the middle impeller and water seal.　　In fact, the pumps I am going to talk about here have a wide range of uses. Pumps are required for both civil and military purposes, as well as for advanced technologies, especially in the mining, chemical, metallurgical and other industrial sectors. It is a widely used general mechanical equipment. Most pumps are corroded or severely corroded　　 confirm whether the pressure capacity of the pipeline meets the requirements, and conduct hydrostatic test if necessary.