As for the guide rail elevator installed outdoors,BaodingGuide rail chain type lifting cargo elevator, it is often exposed to rain and sunlight, so special attention should be paid to regular maintenance and inspection to avoid accidents.How to effectively prevent electric shock by using a hydraulic lifting platform It is very common to add a leakage protector, and the cost is not high. It is both affordable and safe, and can effectively prevent electric shock.Baoding,Card lock; it is also a tool used to prevent equipment from falling suddenly due to accidents. It can be used in combination with card locks and explosion-proof valves.The anti-rust work of the aerial work vehicle generally needs to be paid attention to when the aerial work vehicle has not been used for a long time. How should we do anti-corrosion for the body of the aerial work vehicle? This is actually very simple. You don’t need to spend money to go to the repair station for anti-corrosion. As long as our car owners use some materials that they can find at hand, it can be realized. At the same time, paying attention to driving habits can ensure that the aerial work vehicle does not rust. Here are a few points that can be used as a reference.Krasnovodsk,Prepare the foundation according to the foundation plan, pay attention to the alignment, leveling, and alignment to ensure the level of the foundation and various requirements for use.Low cost: The cost is much lower than that of the scissor-type mobile lifting platform, so when purchasing a lifting platform, you must consider the scope of use of the lifting platform, the frequency of work, there must be no dirt on the friction surface. If there is dirt, it needs to be washed off with gasoline or thinner; the gear box gearbox, external gear and other parts of the equipment and the hydraulic oil must be in accordance with the requirements in the table; Correctly maintain the hydraulic guide rail lift. Regularly check whether the wire ropes in each part are broken or loose. If this phenomenon is found replace them in time. If there is any looseness, it should be tightened in time. The connecting bolts of the equipment should be checked for tightness when the body is under pressure. All connecting shafts should be equipped with cotter pins; check whether each mechanism is operating normally, whether there is noise or failure , to eliminate all faults in a timely manner; when installing dismantling and adjusting the slewing mechanism of the equipment, it is necessary to pay attention to the parallelism between the reducer and the center line of the gear, and the appropriate meshing gap; conduct a comprehensive inspection of the equipment regularly, whether the wires and cables are If there is damage, replace it in time and continue to run after troubleshooting; ensure that the bearings of the motor, each box, distribution box and brushes must be kept clean, and the travel switch points of each safety device must be safe and reliable.

When installing, dismantling and adjusting the slewing mechanism, care should be taken to ensure that the centerline of the slewing mechanism reducer is parallel to the centerline of the gear, the meshing surface is not less than %, and the meshing clearance is suitable.There are abnormal noises on the hydraulic lifting platform It is a normal phenomenon that the hydraulic lifting platform has abnormal noises, especially for equipment that has been used for a long time. Overloading: Due to overloading, the hydraulic lifting platform's own carrying capacity is overloaded, just like the reason why people will shout when they are overloaded to carry things, so don't overload!Frequently check whether the various mechanisms are operating normally and whether there is any noise. If a fault is found, it must be eliminated in time.Quality inspection report,The boxes and distribution boxes of the hydraulic lift are always kept clean, and the dust on the electrical equipment is cleaned in time.Before the elevator manufacturer connects the motor to the elevator, please make the keyway of the motor shaft perpendicular to the tightening bolt. In order to ensure uniform force, please screw on the mounting bolts at any diagonal position first but do not tighten them tightly, then screw on the other two mounting bolts at diagonal positions, and then tighten the four mounting bolts one by one. Finally, tighten the tension bolts. All tightening bolts need a torque wrench to fix according to the marked fixed torque data and check whether the lift and lifting platform are used.How should we check the construction site of the construction hoist? you know?If the motor of the hydraulic lift is overheated, stop the machine in time and continue running after troubleshooting. The motor bearings must be in good condition.

The surface of the brushes of each part should be kept clean, and the pressure of the brushes should be adjusted so that the area is not less than %. Professional elevator factory, large quantity favorably, high quality and low price. Fire-resistant-waterproof-high temperature resistant, safe and reliable.Marketing Department, and new and old customers are welcome to come to consult.The hydraulic torque converter and compensation system are faulty, such as hydraulic torque converter failure, power shift failure, high oil temperature, etc. The hydraulic torque converter is weak, the hydraulic oil volume is insufficient, the pressure is not properly adjusted, and the back pressure is insufficient. Check Torque converter oil quality (whether hydraulic transmission oil is misused), dosage, check torque converter pressure regulating valve, back pressure valve and its set pressure value Power shift failure. Quick return valve, pressure reducing valve, power transmission valve, The reversing valve is stuck and internal leakage. The oil pollution is serious. Check the cause of the valve stuck and eliminate it accordingly. Filter or replace the hydraulic oil. If the oil temperature rises too much, check whether there is any problem with the cooler, check the quality of the hydraulic oil and the brand hydraulic The boarding bridge is also called a hydraulic loading and unloading platform,BaodingTwo ton lifting cargo elevator, which can realize fast loading and unloading of goods. It has a simple structure design, flexible and convenient use, and high work efficiency. It is widely used and popularized in the market.Conscientiously write the special construction plan for installation and construction, and make safety technical disclosures to the installers.Baoding,BaodingCapable of lifting cargo elevators,The price is guaranteed, the service is guaranteed, and it is a large-scale logistics and storage equipment service company directly operated by the manufacturer. Since the fixed lift is a mechanical device, the quality and performance of the product must be good. Do not accept the products of some manufacturers whose quality is not up to standard, so as to avoid some safety hazards in use.Outriggers: mechanical outriggers, hydraulic outriggers ordinary hand-operated outriggers, pull-out outriggers.Regular maintenance Regularly check whether the circuit system of the hydraulic lifting platform is loose, and check whether the wires and cables are aging and damaged, which may cause leakage of the line. If there is