After the goods are transported, clean up the debris on the platform.Avoid working in an environment. In the event of rain, snow and other weather, the use of the hydraulic lifting platform should be stopped to prevent the occurrence of a short circuit, resulting in electric leakage and electric shock; non-professionals are strictly prohibited from disassembling electrical appliances such as hydraulic lifting platforms. In the event of an accident, you can’t disassemble without permission to eliminate the cause. You must report to the manufacturer for repair in time, inform the phenomenon of the accident and the manufacturer will guide you to complete the inspection or send someone to repair it; do not disassemble the appliance without permission! Professional elevator factory guarantees quality, guarantees service. Guarantees quality. Your satisfaction is our pursuit! Welcome to inquire.Baja ,Check whether the self-locking device of the differential protector is normal before working at heights.Check the limit switch to see if all the limit switches are loose. If so, please tighten them. Pay special attention to the ultra-high protection stroke of the hydraulic lifting platform to avoid accidents caused by the equipment exceeding the high safety height; check the pins (ear pins and center pins) Check whether the nuts, nuts, screws, etc. are loose, if any, should be reinforced immediately; ensure that the hydraulic lifting platform rises and falls smoothly; outriggers (for high-altitude operating platform)Malangwa,Hydraulic system: mainly oil cylinders, high-strength chrome-plated rods, Japanese NOK seals, self-made external integrated pump stations, oil pipelines, gear pumps, solenoid valves, etc. The Japanese NOK seal used in the oil cylinder has good wear resistance, which ensures that the oil cylinder series will not leak oil for a long time. The gear pump pumps the oil in the oil tank into the oil circuit and enters the oil cylinder, the ascending and descending speed, and contains an emergency descending device to ensure that the guide rail hydraulic lifting platform can descend safely in case of an emergency.The load of this series of products is divided into . to . tons, and can also be customized according to user requirements, with a load of up to tons.Use Hydraulic lifts are widely used in various industrial enterprises and production lines such as automobiles, containers, mold manufacturing, wood processing, chemical filling, etc., to meet the lifting needs of different operating heights, and can be equipped with various table forms (such as balls, rollers, Turntable, steering, tilting telescopic), with various methods (separate, linkage, explosion-proof) with the characteristics of stable and accurate lifting, frequent starting, large load capacity, effectively solving the difficulties of various lifting operations in industrial enterprises, so that Production operations freely. The professional elevator factory has advanced technology strict testing, more affordable prices, and more discounts are in progress, welcome to consult.

The motor connection is wrong. When the delta connection motor is wrongly connected into a star shape, the motor still runs with full load, and the current flowing through the stator winding will exceed the rated current, and even cause the motor to stop by itself. If it overheats, it will burn out. When the star-connected motor is wrongly connected into a triangle, or the motor with several coil groups connected in series to form a branch circuit is connected in parallel with two branches, it will cause the winding and core to overheat, and in severe cases, and checked according to the bending fatigue strength of the tooth root. The bracket bracket is used to fix and support all the mechanical parts and some electrical components of the elevator box. It is mainly welded by side plates, connecting pipes and connecting pieces. You can choose any product, and the professional elevator factory has safe and secure transactions. At the same time, many craft holes are designed on the two side plates. Because the worm gear mechanism has the advantages of large transmission ratio, compact structure, small impact load, it also has the characteristics of reverse self-locking. It can ensure that the transmission mechanism can self-lock when the motor is powered off during the process of transporting patients, so the worm gear reducer is selected. The involute worm is used, the material is steel, and the helical surface is quenched to improve the transmission efficiency and increase the wear resistance. The material of the worm gear is polyoxymethylene. The plastic worm gear has the advantages of good processing economy, stable transmission, vibration absorption and noise reduction, light weight, wear resistance and self-improvement, which makes the design of the elevator more humanized.Whether it is used outdoors or indoors, some small problems will inevitably appear after a long period of time. At this time, what we should do is to maintain and maintain the elevator. How to follow the steps correctly It has become a difficult problem, and I will answer it with you.project, and the dust on the electrical equipment is cleaned in time.Precautions for using guide rail elevators Precautions for using guide rail elevators: It is strictly forbidden to overload, transport flammable and explosive products and other products.Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, the lift also has a lot of safety equipment.

The use of the hydraulic lifting platform The user can choose the power mode and configuration according to his own scope of use: the power system includes: DC power supply, single-phase or three-phase power supply and diesel engine.target,The safety device of the guide rail hydraulic lifting platform The mechanical part of the guide rail hydraulic lifting platform mainly includes the hydraulic system and the mechanical device.Now we have more and more demands for elevators,Baja Two story cargo elevator, so the editor will introduce the maintenance work of guide rail elevators. When we usually use the guide rail type elevator, we should often carry out inspection, maintenance and maintenance, which will not only prolong the service life of the guide rail type elevator, but also make it work more powerfully! For example, there should be enough oil in the transmission part,Baja Warehouse elevator, and the wearing parts must be checked,Baja Guide rail type cargo elevator cargo elevator, repaired or replaced frequently. For mechanical bolts, especially parts that vibrate frequently, such as slewing rings and lifting arm connecting bolts check whether they are loose. Loose must be tightened or replaced. The steps of maintenance are introduced below: important maintenance work of the rail-type elevator. Regularly check the tire pressure of the rail-type elevator and whether the condition of the bearing is normal; regularly check whether the structure of the bracket and the panel is in good condition. Grease is added once a month; the wearing parts must be checked, repaired or replaced frequently, and the parts that vibrate frequently, such as bolts and slewing bearings, should be checked for looseness. If they are loose, they must be tightened or replaced immediately.Many people think that the strength of the elevator itself is relatively high when using the elevator, so they did not strictly follow the installation method in the manual during the installation process, but they do not know that this will cause increased wear and tear of the parts and inflexible operation, and pay attention to the work The installation precautions corresponding to the environment should not be ignored. Correct installation, use and maintenance of elevators are an important part of ensuring the normal operation of mechanical equipment. Therefore, when you install the elevator, please be sure to strictly follow the installation and use related matters below, and assemble and use it carefully.Baja ,It is best not to cover the aerial work vehicle and park the vehicle outside. If it is windy and rainy, the clothing will repeatedly slap the car paint, especially if the car blows sand on the clothes, it will draw many fine scratches on it. Because it will turn black over time. In addition, when the wind does not directly spray powder or clean the sand on the mechanism, but it should be washed with water, and prevent the sand particles on the paint surface from being scratched by the vacuum cleaner.Safety performance: The lifting structure is made of high-strength manganese steel rectangular tube, and the scissor-type mechanical mechanism is easy to maintain, with strong stability and high carrying capacity. The maximum lifting height is about meters, and the maximum load is about tons. .Pay attention to check whether there are any broken wires and loose strands in the wire ropes of each part. If it exceeds the relevant regulations