What kind of function can be achieved by installing the elevator? Before installation, confirm whether the motor and the elevator are intact, and strictly check whether the dimensions of the parts connected to the motor and the elevator match. Here are the dimensions of the positioning boss of the motor, the input shaft and the groove of the elevator. Fitting tolerances.Unscrew the screw on the dust-proof hole outside the flange of the elevator, adjust the PCS system ring to align the side hole with the dust-proof hole, and tighten the inner hexagon. After that, remove the motor shaft key.Bruges,Always check all wires and cables for damage.Brake operators of various mechanisms on the equipment should regularly check and adjust the gap between the brake shoe and the brake wheel to ensure flexibility and reliability. Long-term promotion of freight elevator factory, old brand, quality guaranteed!Ouesso,BrugesThree ton cargo elevator,The use of the hydraulic lifting platform The user can choose the power mode and configuration according to his own scope of use: the power system includes: DC power supply, single-phase or three-phase power supply, and diesel engine.What is the new price of a fixed lift? Professionally improve the quality assurance of the freight elevator factory. The preferential activities are in progress and new and old customers are welcome to come to consult.Are the water cooling and air cooling of the hydraulic station the same?

It is strictly forbidden for personnel to take the freight elevator to go up and down floors and climb.Function: Convenient unloading, strong stability, low maintenance cost. It is suitable for various vehicles on the loading and unloading yard and places with relatively heavy traffic. Loading and unloading platform, lifting platform, unloading platform: Anti-slip device: This device is welded by steel plates, scratches, small rocks on the driving tires, there may also be a peeling paint spot, and a small rust will appear after a long time. Because most of these scars are small, they are easy to ignore. Therefore, check regularly, the engine compartment cover and its surroundings, and once found, go to a professional beauty shop for processing.Quality improvement, the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, the lift also has a lot of safety equipment.Walking: assisted self-propelled, two-wheel traction, self-driving, and car modified.

Regarding the cleanliness of the hydraulic station, is there any relevant rule requirement?Price,When installing, dismantling and adjusting the slewing mechanism, care should be taken to ensure that the centerline of the slewing mechanism reducer is parallel to the centerline of the gear, the meshing surface is not less than %, and the meshing clearance is suitable.What safety tools are there on mobile lifts Explosion-proof valves: often seen in large hydraulic equipment, especially heavy equipment, the main effect can prevent the oil circuit from bursting or the pressure of the oil circuit is too high to cause problems with the equipment. Regarding small lifts The installation of explosion-proof valves depends on the needs of customers but large-scale equipment basically needs to be installed.Frequently check the humidity of the aerial work vehicle that is prone to water accumulation. It is inevitable that the aerial work vehicle is driving in rainy and snowy weather, or on muddy roads. The bottom and some gaps and indoor floors are easy to accumulate sludge. If the owner does not clean it in time, this will hide the moisture. Therefore,BrugesFixed lifting hydraulic cargo elevator, the outer edge of the wheel hub, the door the corner of the bottom of the trunk, the key hole and the wiper frame and other areas should be checked regularly,BrugesTwo layers of hydraulic lifting cargo elevator, and the drainage holes in the door and various parts should be kept unblocked to ensure that the car seat covers, carpets and floors are protected from humidity. Rusty fittings.Bruges,Precautions for using guide rail elevators Precautions for using guide rail elevators: It is strictly forbidden to overload, transport flammable and explosive products and other products.The hydraulic lifting platform can be divided into: four-wheel mobile type, two-wheel traction type, car type, auxiliary self-propelled type, and the lifting height ranges from a meter to s meter.Hydraulic system: mainly oil cylinders high-strength chrome-plated rods, Japanese NOK seals, self-made external integrated pump stations, oil pipelines, gear pumps, solenoid valves, etc. The Japanese NOK seal used in the oil cylinder has good wear resistance, which ensures that the oil cylinder series will not leak oil for a long time. The gear pump pumps the oil in the oil tank into the oil circuit and enters the oil cylinder, thereby driving the top of the rod and raising the equipment; The valve is used to adjust the oil output, the ascending and descending speed, and contains an emergency descending device to ensure that the guide rail hydraulic lifting platform can descend safely in case of an emergency.