Nowadays, dismantling and adjusting the slewing mechanism, care should be taken to ensure that the centerline of the slewing mechanism reducer is parallel to the centerline of the gear, the meshing surface is not less than %, and the meshing clearance is suitable.Catherine Hardwicke ,Advantages of operating cost: Low failure rate due to the use of advanced hydraulic system and good methods, the failure rate of elevator operation can be reduced to a minimum. Less power consumption: When the hydraulic elevator goes down, it is driven by the pressure generated by its own weight,Catherine Hardwicke Fixed guide rail type cargo elevator, which greatly saves energy.Safety performance: The lifting structure is made of high-strength manganese steel rectangular tube, and the scissor-type mechanical mechanism is easy to maintain, with strong stability and high carrying capacity. The maximum lifting height is about meters, and the maximum load is about tons. .Udine,It is strictly forbidden for personnel to take the freight elevator to go up and down floors and climb.It is strictly forbidden to switch the electric control switch with wet hands. Many people tend to ignore this detail. Although the safety voltage of the hydraulic lifting platform is below V, if you touch the power supply with your hands, it may cause lifting failure in light cases, or electric shock accidents in severe cases.Test the freight elevator every day to see if the freight elevator can operate normally.

Frequently check whether the various mechanisms are operating normally and whether there is any noise. If a fault is found, it must be eliminated in time.The scissor type aerial work platform is a professional aerial work equipment with a wide range of uses.The anti-rust work of the aerial work vehicle generally needs to be paid attention to when the aerial work vehicle has not been used for a long time. How should we do anti-corrosion for the body of the aerial work vehicle? This is actually very simple. You don’t need to spend money to go to the repair station for anti-corrosion. As long as our car owners use some materials that they can find at hand,Catherine Hardwicke Elevating cargo elevators require, it can be realized. At the same time, paying attention to driving habits can ensure that the aerial work vehicle does not rust. Here are a few points that can be used as a reference.Statistics,The design of the hydraulic lifting platform is unreasonable. When the designer designs the cylinder barrel and rod, if there is a problem with the design size and angle, then there will definitely be problems in the later stage. Therefore, it is necessary to confirm the technical strength of the manufacturer when working on a hydraulic lifting platform; what is the problem with the sound of the oil cylinder of the hydraulic lifting platform? Design drawings to make, the angle of the oil cylinder is slightly deviated, it will cause the friction between the cylinder barrel and the rod, which will cause the sound; the seal quality of the hydraulic lifting platform is different and the use of different seals will also affect the sound of the oil cylinder, and the seal with excellent material The continuous friction between the parts and the cylinder wall will cause the sound to be very loud, and long-term wear and tear may scratch the oil cylinder and cause oil leakage, so when the hydraulic lifting platform is used, pay attention to ask the manufacturer what brand and material the seal is used; In some cases of mechanical running-in, then don’t worry. It’s just a running-in problem between mechanical parts. It will disappear naturally.Regular maintenance Regularly check whether the circuit system of the hydraulic lifting platform is loose and check whether the wires and cables are aging and damaged, which may cause leakage of the line. If there is, it should be repaired in time to avoid electric shock.Many people think that the strength of the elevator itself is relatively high when using the elevator, so they did not strictly follow the installation method in the manual during the installation process, but they do not know that this will cause increased wear and tear of the parts and inflexible operation, and pay attention to the work The installation precautions corresponding to the environment should not be ignored. Correct installation, use and maintenance of elevators are an important part of ensuring the normal operation of mechanical equipment. Therefore, when you install the elevator, please be sure to strictly follow the installation and use related matters below, and assemble and use it carefully.

The hydraulic lifting platform is widely used in the maintenance of industrial and mining enterprises, municipal construction and decoration of hotels and hotels, with reliable quality and perfect performance.How much does it cost?,Regarding the cleanliness of the hydraulic station, is there any relevant rule requirement?Problems to be considered in the transportation of lifting platforms But in the use of elevators, some relatively large places will purchase lifting platforms that suit their needs according to the requirements of users, which means that the equipment that is too large will exist in the transportation Difficulties, this is also a problem that many users and manufacturers are more worried about. The equipment is large in size and occupies a large area. It is inconvenient to carry it back and forth, and it is very difficult to move. So how should we solve it? Today, the editor will introduce to you in detail how the large lifting platform solves the problem of transportation difficulties.Whether it is used outdoors or indoors, some small problems will inevitably appear after a long period of time. At this time, what we should do is to maintain and maintain the elevator. How to follow the steps correctly It has become a difficult problem,Catherine Hardwicke Elevating cargo elevator Elevating cargo elevator, and I will answer it with you.Catherine Hardwicke ,Always check the connections of the various parts of the hydraulic lift, and tighten them if they are loose. The tightness of the connecting bolts of the body should be checked when the body is under pressure.The cleanliness of the hydraulic station is an important aspect of the elevator hydraulic station, so it should not be careless. Moreover, from a professional point of view, there are relevant rules and requirements, and you should refer to the specification manual