Generally, oxygen aylene is used as the gas source and LPG welding tool is used for heating. The torch of the welding tool shall face the joint and then continuously heat the whole joint. This will avoid excessive local heating.Red copper bars in other regions basically follow the price trend of Tangshan, in which the bid of Jiangsu Steel Works tends to be higher, and most of the downstream prices are asked, and the overall market transaction is fair. The steel mills in Wu an are limited in receiving orders, and the market resources are tight. Most of the merchants are reluctant to sell. Shanxi billet market offers vary, and it is difficult to clinch a deal. The willingness of downstream customers to receive orders is weak, so they hold a cautious wait-and-see attitude. At prepresent, the steel market is in the & quot; golden third& quot; peak season. The market has a good expectation of the future market and a strong willingness to support prices. It is expected that the prices of Tangshan mainstream billets will be stronger next week.Mustasari,The copper pipe has high welding precision, fast production speed, good surface finish and beautiful appearance. Therefore, it is widely used in precision welding industries such as glasses, hardware, electronics, accessories, sanitary ware and kitchenware.After : on October , continue to implement the measures of stopping and limiting production specified in TZBZ [] No. document. All sintering machines and shaft furnaces using wet desulphurization in iron and steel enterprises in the city were shut down, and sintering machines using semi dry desulphurization continued to be shut down for %. The access of vehicles is alicted. The port collection and distribution vehicles are prohibited from entering and leaving the port area. The city s steel, coking electric power, cement, chemical and other key vehicle enterprises are not allowed to transport vehicles into and out of the plant. After : on October , the vehicle enterprises in the above industries will implement % of the peak load shifting emission reduction measures. It is estimated that the average daily consumption of sintering powder in Tangshan will be more than yuan, and the purchase of iron ore may still maintain a small amount of prudence. In addition, due to the influence of industrial users & amp; quot; coal to gas& quot;, the recent performance of coke is weak. Therefore, in terms of steel plant production, the support of raw materials is weak.Tlahuac,The copper tube shall be heated and welded first, and then the joint shall be heated until the heated part turns dark red. At this time, when the filler metal contacts the tube, the filler metal shall melt.Hygiene and health: various modifiers, additives, additives and other chemical components of plastic pipes in copper pipes.The material of the water separator is the same, the expansion coefficient is the same, and the connection with the water separator is not easy to leak. Scope of application: As the copper pipe is more expensive than the plastic pipe, the cost of the floor heating system is higher.

Remove the flame. If the filler metal does not melt, continue to heat the joint and try again. The melted filler metal is sucked into the casing port according to the capillary effect until a complete filler metal ring appears on the casing port. Remove the flame Pay special attention not to let the flame directly contact the filler metal. It should be the heat at the joint that melts the filler metal. In order to clean the copper pipe the welding flux must have a degree of corrosivity, and shall be cleaned after brazing. The so-called & quot; self-cleaning& quot; fluxes are generally not recommended because of their corrosivity.{} The copper pipe welding can be divided into soft welding and hard welding. The soft welding temperature is lower than ℃, and the hard welding temperature is higher than ℃. Hard welding is usually used for silver, gold,MustasariQ345D alloy round steel, steel, copper and other metals. Its welding points are much stronger than soft welding, and its shear strength is - times that of soft welding.The price of tube billets was adjusted and lowered mainly due to the production restriction of environmental protection and the weak demand for temperature and weather. Recently, the terminal demand has also shrunk due to the sudden drop in temperature, causing a weak shock. According to the communication with local traders in Cangzhou, various good news last week led to the shipment of thermal expansion pipes in Cangzhou in the past two weeks, which is better in the off-season, and the shipment of some specifications has improved. However, the trading atmosphere in the small and medium-sized pipe market is still cold, and the demand is slowing down gradually. To sum up, it is expected that the market price of Cangzhou seamless pipe will be stable and weak in the near future.Workshop costLet s elaborate on the advantages of copper pipe materials: copper pipe floor heating refers to a heating method that uses hot water as the thermal medium, circulates in the copper pipe heating pipe, heats the floor, and heats the floor through the ground in the form of radiation and convection heat transfer. I. The copper tube has fast heat dissipation effect and strong heat resistance. Even under the condition of high temperature water supply, the service life of the floor heating tube will not be affected. Two. Copper pipe is a metal pipe, it is not easy to leak. Three. High temperature resistance, high pressure resistance, relative to any ordinary plastic pipe. Copper tube floor is warm and resistant to high temperature and pressure. Four. Long service life. Five.The simplest way is to use copper cleaner. Brass, bronze, etc. can be used. Oil stains, fingerprints,MustasariAlloy plate, oxide layers, etc. on the surface can be cleaned with copper cleaner first.Extrusion method: This production method is to cast copper ingots after smelting, and extrude copper tubes by large extruder after secondary heating.

In consideration of the above factors, more and more steel plants have stopped production since October, the formal implementation of production limit in & quot; +& quot; urban heating seasons after November by steel enterprises the demand for iron ore in the future is likely to further deteriorate. The iron ore inventory of the steel plant is relatively high, and the willingness to further replenish the inventory is not strong. In terms of supply, the fourth quarter is generally the peak period for the shipment of imported ores. Although the production of domestic mines has been reduced due to environmental protection, the quantity of * * * is relatively limited. In general, the short-term iron ore market may lack upward momentum.How much does it cost?,[] Welding process of copper pipe Clean the end and seven ports of steel pipe with steel wool. Do not use abrasive cloth or abrasive paper to clean, because it will affect the clean interface and result in poor welding effect.Re treat the water quality.Advantages: good quality, fine structure, high density, high pressure resistance, large bending deformation, suitable for frequent cold and heat exchange, and large size copper tube can be produced.Mustasari,Three of the five major application fields of copper plate,MustasariAluminum rod, copper bar and copper tube: copper is used to manufacture, and gun parts in the national defense industry. Every million rounds of copper are produced, - tons of copper are needed.In the morning trading today, the price of domestic copper bar fell. According to the monitoring data of Lange Steel s cloud business platform, the average price of * mm hot rolled strip in key cities in China is , down yuan from yesterday. Futures prices fluctuated, and the prices of spot market manufacturers eased slightly today. According to the feedback the market was mainlysee yesterday, which caused the overall transaction blocked, because it will affect the clean interface and result in poor welding effect.