What is the stainless steel passivation of alloy pipe?I-beam has wide flange, thin web, many specifications and flexible use. It can save metal by % ~ % when used in various truss structures. Because the inner and outer sides of the flange are parallel and the edge end is at right angles, it is easy to assemble and combine into various components, which can save about % of the welding and riveting workload, greatly accelerate the construction speed of the project and shorten the construction period.Dahaon, which provides us with great assistance.Siuna,The flange of H-beam is of equal thickness,DahaonPrice of 12Cr1MoVG alloy pipe, including rolling section and combined section composed of three plates welded. All I-beams are rolled sections. Due to poor production technology, the inner edge of the flange has a slope of : The rolling of H-beam is different from that of ordinary I-beam. Only one set of horizontal rolls is used. Because its flange is wide and has no inclination (or the inclination is very small), a group of vertical rolls must be added for rolling at the same time. Therefore its rolling process and equipment are more complex than ordinary rolling mills. The maximum height of rolled H-section steel that can be produced in China is mm, which exceeds the welded composite section.→ compared with general section steel, it has the advantages of low cost, high precision and small residual stress. It does not need expensive welding materials and weld detection, and saves about % of the manufacturing cost of steel structure.It is widely used in various fields of national economic construction, such as buildings, bridges, power stations, oil drilling platforms, vehicles, highways, subways, steel structure plants and large warehouses

When selecting I-beam in structural design reasonable I-beam shall be selected according to its mechanical properties, chemical properties, weldability and structural size. I-beam is mainly divided into ordinary I-beam, it is divided into wide, medium and narrow flange I-beams.The use of welded steel mesh in China is still in its infancy. At present, steel welded mesh was listed as a key implementation project by the science and Technology Commission and the Ministry of construction, and specifications and procedures were formulated.Performance parameters and application scope of I-beamQuality inspection report,Classification introductionAiming at the connective tissue and texture produced in stainless steel plate Position and other crystal defects are generally removed by heat treatment processes such as quenching or quenching. The effect of quenching is to optimize the crystal, eliminate structural defects, reduce strength, improve plastic deformation, and also conducive to cold drawing. In the production and manufacture of cold drawn alloy pipe, quenching machinery and equipment cannot be lacked. Therefore, the formulation of appropriate annealing process is a necessary condition to ensure that the alloy pipe mechanism meets the standard and the commodity does not crack. If the manufacturer in order to better one sidedness, reduce the product cost and reduce the quenching process, it will eventually lead to bad harm to the product quality.Carburizing: carburizing is the process of penetrating carbon atoms into the surface layer of steel. It also makes the low-carbon steel workpiece have the surface layer of high-carbon steel,DahaonWholesale of I-beam manufacturers, and then after quenching and low-temperature tempering, the part of the workpiece can maintain the toughness and plasticity of low-carbon steel.

Application characteristics of I-beam:Management Department,The specification of pass design I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is. The types of I-beam include hot-rolled ordinary I-beam, light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~, expressed as No. ~ No., and the inclination of inner wall of leg is : The pass system of rolled I-beam includes direct pass system, I-beam can also adopt special rolling method. Spiral seam submerged arc welded steel pipe for general low-pressure fluid transportation (SY / t- is a submerged arc welded steel pipe for general low-pressure fluid transportation such as water, gas, air and steam, which is made of hot-rolled steel strip coil as pipe blank, often warm spiral forming and double-sided active submerged arc welding or single-sided welding.H-section steel is an economic section high-efficiency profile with more optimized section area distribution and more reasonable strength weight ratio. It is named because its section is the same as the English letter 'H'. There is no slope on the inner side of the two outer edges of H-section steel, which is straight. This makes the welding and splicing of H-section steel simpler than I-section steel, better mechanical properties per unit weight, and can save a lot of materials and construction time.Dahaon Hot stamping. Fix the plan product workpiece or preformed vacancy on the rotating journal, with the wheel working pressure vacancy, radial wheel. After one or several solutions, there can also be a variety of methods for the whole process of hollow thick wall rotating body products. Products manufactured by high-precision processing method have excellent physical properties, specification scope, mold shell and software requirements,Dahaon12Cr1MoV alloy pipe, which are very simple, very easy to be replaced and relatively low product cost. The processing time is not long enough, the processing capacity is not high, the total length of processing pipeline is limited, and the size of machinery and equipment is generally short.b. The professional two-sided arc welding processing technology can complete the electric welding at a good position, which is not easy to have the disadvantages of staggered joint, welding deviation and incomplete penetration, and it is very easy to manipulate the welding quality.Introduction to product knowledge of alloy pipe: