which can not only save resources, not occupy the natural environment, but also purify the environment. The transportation of gas can meet the requirements of long-distance transportation, prevent actual operation and maintenance, meet the requirements of thermal insulation and cold protection, reduce heating equipment, unique and convenient installation, it is more convenient to use. It can also be used for the transportation of floor heating and hot springs.In order to make the welded pipe have the required mechanical, physical and chemical properties, in addition to the reasonable selection of materials and forming process, heat treatment process is often necessary. In addition, the mechanical, physical and chemical properties of aluminum, copper, magnesium, titanium and their alloys can be changed by heat treatment to obtain different service properties.Monte Carlo,Next, let&#;s introduce the operation steps of roll adjustment during roll change. First of all, we must replace the specification and model of the welded pipe manufacturer. Generally, replace the complete set of rolls. The adjustment process of the rolls is as follows: first, draw an axis from the channel of the generator set to the import and export with stainless steel wire for adjustment, so that the holes of each frame plate are on the same axis, and the bottom line of forming ethics meets the technical standards. Special rolling method. When it is difficult to roll the required I-beam by the usual rolling method for some reason, the special rolling method can be used to make full use of the skills of uneven deformation and pass design. For example,Monte CarloHow much is 16# I-beam per meter, the wave rolling method can be used; for example, when the billet is wide and small I-beam is required to be rolled, the negative rolling method can be used Spread rolling, etc.Levin,I-beam is widely used in buildings or other metal structures.Aiming at the connective tissue and texture produced in stainless steel plate Position and other crystal defects are generally removed by heat treatment processes such as quenching or quenching. The effect of quenching is to optimize the crystal, eliminate structural defects, reduce strength, improve plastic deformation, and also conducive to cold drawing. In the production and manufacture of cold drawn alloy pipe, quenching machinery and equipment cannot be lacked. Therefore, the formulation of appropriate annealing process is a necessary condition to ensure that the alloy pipe mechanism meets the standard and the commodity does not crack. If the manufacturer in order to better one sidedness, reduce the product cost and reduce the quenching process, it will eventually lead to bad harm to the product quality.Whether I-section steel is ordinary or light, because the section size is relatively high and narrow, so it can only be directly used for members bent in the plane of their web or form lattice stressed members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application. I-beam is widely used in buildings or other metal structures.

Welded steel pipes need to be processed through various processes before application. The heat treatment of welded steel pipes is a very important link in the processing of welded steel pipes. Hot working is a metal hot working process in which metal materials are heated insulated and cooled in a certain medium, and their metal properties are controlled by changing the metallographic structure on the surface or inside of the material. During the heating and cooling process of structural welded steel pipe workpiece, due to the inconsistency of cooling speed and time between the surface and the core, the temperature difference will be formed, which will lead to uneven volume expansion and contraction and produce stress that is, thermal stress.On the other hand, when the steel structure changes during heat treatment, that is, austenite transforms into martensite, the increase of specific volume will be accompanied by the expansion of workpiece volume, and each part of workpiece will undergo phase transformation successively, resulting in inconsistent volume growth and structural stress. Due to the change of tissue stress the tensile stress on the surface and the compressive stress in the heart are just opposite to the thermal stress. The magnitude of microstructure stress is related to the cooling rate, shape and chemical composition of martensitic transformation zone materials.Pass designLet's see,At present, there is still a big gap in the production technology of C-section steel between China and foreign countries.The production process can be summarized as follows: pre leveling → finishing → straightening → post leveling. Flat steel / A / B steel with width of -, thickness of -, rectangular section and slightly pure edge. Flat steel can be finished steel, or it can be used as blank for welded pipe and thin slab for laminated thin plate.Plan scheme : Martensitic chromium alloy pipe and chromium alloy pipe with Cr composition exceeding %, without high carbon steel and high chromium alloy pipe. The aqueous solution contains % sodium cyanide % ~ % (volume ratio), the solution temperature is ~ ℃, and the solution time is min.

When selecting I-beam in structural design, reasonable I-beam shall be selected according to its mechanical properties, chemical properties, weldability and structural size.Installation requirements, Small longitudinal crack Tungsten; can improve the red hardness and thermal strength of steel, and can improve the wear resistance of steelBecause all parts of I-beam are arranged at right angles I-beam has the advantages of strong bending resistance,Monte Carlo15CrMo thick wall alloy pipe, simple construction, cost saving and light structural weight in all directions, and has been widely used. The inner and outer sides of the flange of the I-beam are parallel or close to parallel, and the end of the flange is at a right angle,Monte CarloSuperalloy tube GH5188, so it is named parallel flange I-beam. The web thickness of I-beam is smaller than that of ordinary I-beam with the same height of web, and the flange width is larger than that of ordinary I-beam with the same height of web, so it is also named wide edge I-beam.Monte Carlo,What is nitriding of alloy pipeMetallization: refers to the process of penetrating metal atoms into the surface layer of alloy steel pipe. It is to alloy the surface layer of steel so that the workpiece surface has the characteristics of some alloy steel. Aluminizing, chromizing, boronizing, siliconizing and so on are commonly used in production.Function of I-beam: where is I-beam mainly used?