When the slurry pump is working, the pump needs to be placed on land,HapsaluQJ submersible pump, the suction pipe in water, and the pump needs to be started. Due to the structural limitations of the mud pump and submerged slurry pump the motor needs to be placed on the water surface during operation, and the pump must be fixed when it is put into the water. Otherwise, the motor will fall into the water　　No matter what type of slurry pump you need, Ritter pump will provide you with the highest quality slurry pump products; The latest development of submersible slurry pump technology in recent years The diving depth has increased from meters to meters!Hapsalu,　　 water　　Is called cavitation phenomenon.Isfara,　　Pump. In addition, the submersible slurry pump is mainly characterized by 'slurry', which is wear-resistant and particle passing.　　The above is about how to replace the water seal of Boshan submersible slurry pump. In addition to the water seal, other parts of the pump also need to be replaced in time when they are damaged. Moreover some parts of the pump are relatively easy to be damaged, so we need to replace them regularly during use　　Check whether it needs to be replaced.　　 Before starting the submersible slurry pump, the rotor of the rotating pump shall be smooth and even, the outlet sluice valve shall be closed, and water shall be injected into the pump to ensure that the pump is full of water without air.

　　 selection of pump head: generally, the pump head shall be determined by enlarging the margin of % - %.　　 There are several reasons for the severe vibration of the pump body: the phenomenon of unbalanced rotation of the electric rotor.　　It should be /-/ between. When the packing is worn the packing gland can be properly pressed. If it is worn too much, it should be replaced. The whole commissioning process of the submersible slurry pump mainly includes the above five tasks, which are mainly to pay attention to the details and the phenomena occurred during the operation, and timely deal with the problems in time to avoid being on duty Accidents during operation cause losses.management,　　This phenomenon shows that the failure of the pump is not only a material problem, but also reminds the pump designers and producers that in addition to good working conditions, the pump should also have good corrosion resistance,HapsaluDeep well pump, high reliability and long service life. The pump shall be designed in addition to the conventional design method of fluid mechanics　　 Inspection before installation: Check the specification, size and quality of thick and thin accessories.　　 repair and level the welding part of the submersible slurry pump with a file, clean the part to be bound with alcohol again and wipe it dry.

　　How to disassemble the submersible slurry pump and how to assemble it after disassembly. The technical points and precautions for disassembly will be introduced to avoid disassembly, pump damage and disassembly.High quality and low price,　　 When stopping the operation of the submersible slurry pump, close the cock of the vacuum gauge and pressure gauge and the gate valve on the water outlet pipeline, and After that, cut off the power supply of the motor. If the temperature of the environment is low, open the square plug at the lower part of the pump body to remove the remaining water to avoid frost cracking. During operation, the maximum temperature of the bearing shall not exceed ℃, and the quantity of calcium base grease used for lubricating oil bearing shall be the same as that of the bearing body　　 there are two different installation methods, fixed automatic coupling installation system and mobile free installation system.　　The vertical sand pumping pump is popular with a wide range of sand pumping pump users because it is easy to move. This equipment is made of high-tech endurance data. Its service life has been greatly improved, and the maintenance frequency has been reduced, and the income has been increased.Hapsalu,　　 Before starting the submersible slurry pump, the rotor of the rotating pump shall be smooth and even, the outlet sluice valve shall be closed,HapsaluPipeline pump, such as apartment, residence, villa water supply, factory water supply, water supply system, drinking water system and water treatment. In short, close the cock of the vacuum gauge and pressure gauge and the gate valve on the water outlet pipeline, and After that, cut off the power supply of the motor. If the temperature of the environment is low, open the square plug at the lower part of the pump body to remove the remaining water to avoid frost cracking. During operation, the maximum temperature of the bearing shall not exceed ℃, and the quantity of calcium base grease used for lubricating oil bearing shall be the same as that of the bearing body