and the allowable difference is specified in the corresponding standards. The length selection range of domestic I-beam is divided into -, - and - according to different specification numbers. The length selection range of imported I-beam is generally -.Alloy pipes can be used for heating (cooling) projects.Symbiosis with the sea, Manganese: it can improve the strength of steel, weaken and eliminate the adverse effects of sulfur, and improve the hardenability of steel. High alloy steel (high manganese steel) with high manganese content has good wear resistance and other physical propertiesFunction of I-beam: where is I-beam mainly used?Bochum-Hordel,Stages needing attention in the production and manufacture of alloy tubesWhether I-section steel is ordinary or light because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application. I-beam is widely used in buildings or other metal structures.H-beam is a widely used profile in steel structure buildings. It is different from I-beam. The first is the flange, and the second is that the inner surface of the flange has no inclination, and the upper and lower surfaces are parallel. The section characteristics of H-beam are obviously better than those of traditional I-beam, channel steel and angle steel.

The small length of repair welding is mm; The raw material shall not exceed mm after grinding by welding edge.Characteristics and application of galvanized pipeIt is a potential rolled strip steel with rectangular section for general purpose. It is very common on construction sites. Its specifications are expressed in thickness and width. At present, most of the flat steel on the market are finished steel, which can be used ready-made for components, ladders, bridges and fences. Flat steel can also be used as blank for welding rigid steel and slab for laminated thin plate.Where to sell API,Difference and application description between H-beam and I-beamPassivation treatment operation of alloy pipeBecause the section size of ordinary I-beam and light I-beam is relatively large and narrow the moment of inertia of the two main shafts on the section is quite different, which limits its application range. I-beam shall be selected according to the requirements of design drawings. In the structural design, the use of I-beam should be reasonably selected according to the mechanical properties, chemical properties, the axial movement is small, and the working slope is not required,Symbiosis with the seaSmall diameter thick wall alloy pipe,Variable costDry processing technology: after passivation treatment, parts shall be dried with air compression or hot gas, or drying treatment or air drying can be selected.Metric welded pipe: it is used as seamless pipe in standard. The welded steel pipe expressed by outer diameter * wall thickness mm is welded by hot and cold strip welding of general carbon steel, high-quality carbon steel or Puneng low alloy steel, or it is made by cold drawing after hot strip welding. Metric welded pipe is generally used as structural parts, such as transmission shaft, or to transport fluid. The thin wall is used to produce furniture and lamps. It is necessary to ensure the strength and zigzag test of steel pipe.What are the uses of I-beam?Symbiosis with the sea,Pass designIts heat sealing effect is remarkable. It can be directly buried immediately, which can not only save resources, but also reduce consumption, not occupy the natural environment, but also purify the environment. The transportation of gas can meet the requirements of long-distance transportation, meet the requirements of thermal insulation and cold protection, reduce heating equipment, unique and convenient installation, and reduce the construction cycle time of the project. On the whole, it is more convenient to use. It can also be used for the transportation of floor heating and hot springs.After determining the reasonable pickling agent and polishing solution, it is very easy to carry out hot galvanizing for relevant alloy pipes. Use 'phosphating treatment' to degrease the pipes of electrolytic machine equipment, put them into the aqueous solution with zinc salt after pickling and passivation, connect the negative level of electrolytic machine equipment,Symbiosis with the seaHow much is a dn70 galvanized pipe,Symbiosis with the seaWhat is the price of seamless pipe, put them into the cold-rolled steel plate in the direction corresponding to the pipes, and connect the switching power supply, If the current flows from the positive stage to the negative stage, a layer of zinc is deposited in the pipe.