The second is the pickling of the square pipe. Both chemical and electrolytic methods are used when pickling the square pipe. These two methods can remove the oxide skin of the square pipe.The reason why it is divided into two types is that chemical cleaning can only clean the surface very thoroughly, and it is difficult to achieve the desired results in some fine cracks.Sakavin,Upper yield point (& sigma; Su): the large stress before the yield of the sample occurs and the stress decreases for the first time; Lower yield point (& sigma; SL): the small stress in the yield stage when the initial instantaneous effect is not considered.Square tube for automobile half shaft sleeve (gb-) is a high-quality carbon structural steel and alloy structural steel hot-rolled square tube for automobile half shaft sleeve and drive axle housing.Kon TumDerusting grade for the construction process of epoxy, ethylene, phenolic and other coatings commonly used for square pipes, rust and other dirt can be removed by using this derusting grade, and the depth of anchor grain can reach ~ & mu; m,SakavinPVC pipe galvanized steel pipe, which fully meets the requirements of adhesion between layer and square pipe The shot derusting process can meet the technical conditions of near white level (SA) with low operation cost and stable and reliable quality.During the pushing process of spot welding and repair welding elbows, there will be thinning, so manufacturers usually use thick spot pipes. If thin raw materials are used, the products produced must be unqualified. Generally, there are about wires thinned. If the technology is not good or the drawn pipe is used, the thickness is significantly lower than the standard.Plasticity QB square plasticity refers to the ability of metal materials to produce plastic deformation (deformation) without deformation under load.

Square pipe for diamond core drilling (gb-) is a square pipe for drill pipe, core rod and casing for diamond core drilling.In order to ensure the stability of the perforation performance and chemical properties of the billet of the square tube, the operation of the heating furnace shall be frequently, the abnormal conditions shall be handled in time and recorded, and the follow-up posts and quality management department shall be notified in time for handling.Square tube heating process square tube calculates the chip thickness of workpiece. After each regrinding, the service life of the saw blade. Regrinding times of the saw blade. When the saw blade is replaced, the main drive AC motor spindle rotates stepless speed change AC motor feed capacity stepless speed change feed fast return to a constant value center system brush device hydraulic saw cutting system system system represents the quality RA flatness, large burr height cutting Chip length tolerance dimension: width and length . ~ .mm ~ m ~ ~ min kW ~ rpm ( kw ~ mmmin mmmin .kw .kw & times; kW S & mu; m . mm & plusmn; mm about mm about mm about mm high. The total weight of each billet square tube is seconds (including, pipe blank cutting, saw blade return,SakavinHot dip galvanized square pipe steel, opening device, pipe blank discharge, head and tail cutting time, but excluding pipe blank transportation time). The large production capacity of the three saws is T / A. the pipe blank saw has a special reversing device (hydraulic servo device) to reduce vibration and improve the service life of the saw (only during feeding). The sawing machine has two devices distributed at the inlet and outlet (the input area is supported by roller table to ensure the bending of billet) The inlet end after sawing. Open it to ensure that the saw blade does not contact the blank when it returns. & mdash; feed saw gear & mdash; saw gear vibration reduction, as a movable vibration reduction to avoid the axial of the saw blade. & mdash; brush and sweep device & mdash; a driving brush and sweep device is installed at the bottom of the saw blade to clean the iron filings on the teeth and will not affect the service life of the saw blade. &Mdash; saw blade. In order to improve the service life of the saw blade, there is a feeding bench for single size billets that need to be cut, and after weighing, there is a feeding bench for returned billets). The buffer transfer chain transports the billets to the lower roller table of the loader. The billets are turned over from the chain to the roller table by the turnover hook. The weighed qualified billets are loaded into the annular furnace by the loader, and the weighed unqualified billets are transported from the roller table to the removal bench for removal.Quality Assurance,After cold drawing and aging treatment, the yield point is improved, the tensile ultimate strength is also increased, and the plasticity continues to decrease. Due to the reduction of internal stress during aging, the modulus can be basically restored. According to this principle, cold drawing or cold drawing of reinforcement or low carbon steel wire rod is often carried out on site or prefabricated component factory, so as to improve yield strength and save steel.C. special performance steel: (a) stainless and acid resistant steel; (b) Heat resistant steel; (c) Electric heating alloy steel; (d) Electrical steel; (e) High manganese wear resistant steel.The difference between hot-dip galvanized square pipe and cold-dip galvanized square pipe is mainly from the following aspects: the appearance of hot-dip galvanized square pipe is slightly rough compared with cold-dip galvanized square pipe; The appearance of cold galvanized square pipe is smooth and bright.

Tool derusting mainly uses tools such as steel wire brush to polish the surface of square pipe, which can remove loose or oxidized scale, rust, welding slag, etc. The derusting of manual tools can reach grade SA and that of power tools can reach grade SA. If the square pipe surface is firmly attached with iron oxide scale, the derusting effect of tools is not ideal and can not reach the anchor depth required by construction.ranking,If the test results of square tubes fail to meet the provisions of product standards, the unqualified ones shall be selected,SakavinGalvanized square pipe, and double the number of samples shall be taken from the same batch of square tubes for re inspection of unqualified items. If the re inspection results (including any index required by the test of the project) are unqualified, re inspection is not allowed: A. There are white spots in the low magnification; b. Microscopic.The qb square tube rolled from the strip steel through process treatment is generally to unpack, flatten, curl and weld the strip steel to form a round tube then roll the round tube into a square tube, and then cut it to the required length. Nowadays, the forming of qb square tube has solid bending and empty bending. The bending degree of qb square tube shall not be greater than mm per meter, and the total bending degree shall not be greater than the actual bending of the total length. As the name suggests, the bending is compacted, and the internal and external rollers and the internal and external walls of the tube blank are compacted in both directions during the actual bending.Purpose of square tube the purpose of square tube includes construction, machinery, steel construction and other projects, shipbuilding, solar power generation support, steel structure engineering, electric products ( pieces)Sakavin,The general delivery length of qb square pipe is mm-mm mostly mm and mm. Qb square tube is allowed to deliver short length and non fixed length products not less than mm, or in the form of interface tubeProduct description of square tube square tube is a light thin-walled steel tube with hollow square section, also known as steel cold-formed profile. It is a section steel with square section shape and size, which is made of Q hot-rolled or cold-rolled strip or coil as the base material, cold bending and high-frequency welding. In addition to wall thickness thickening, the corner size and edge flatness of hot-rolled special square pipe reach or even exceed the level of resistance welding cold-formed square pipe. Good comprehensive mechanical properties, weldability, cold and hot workability and corrosion resistance, and good low temperature toughness.The disadvantage of empty bending is that during synchronous empty bending at the upper and side, due to the pressure generated by the upper roll and the lower roll at the same time, the forming force is easy to exceed the critical point. All kinds of square tubes, square rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes have formal qualifications. Welcome to telephone inquiry and sincerely invite cooperation! It will cause edge instability and concave and will also affect the stable operation of the unit and forming quality. This is also the different characteristics of qb square tube and round tube empty bending.