the door should be able to withstand and have no deformation; - Deformation not exceeding mm; After the test, it worked normally.Chang'an,High altitude operations and maintenance in areas such as repair, logistics, electricity, transportation, petroleum, chemical, hotel,Chang'anEd, sports center, mining, and enterprise. The lifting system of the lifting platform is driven by hydraulic pressure also known as hydraulic liftingBefore installation, foundation bearing capacity, embedded parts and foundation drainage measures of the installed construction electric elevator and auxiliary heavy equipment comply with the requirements of the special construction plan for the installation and dismantling of the construction electric elevator based on the construction electric elevator foundation acceptance form, concealed engineering acceptance form, and concrete strength report.Frydek-Mistek,With the continuous improvement of urbanization level in China, the number of high-rise buildings in urban areas has sharply increased,Chang'ansouthern suburbs, and the height of buildings has also continued to grow. This has created a demand for high-altitude lifting platform vehicles. Therefore in order to meet the needs of the domestic market and the public,Chang'anCannes , efforts will inevitably be made to design and produce high-altitude lifting platform vehicles.There is no need to set up a computer room above the shaft like an elevator, and the top floor height can be installed at least . meters.The entrance of each landing platform must be equipped with a landing door, which must open towards the landing platform side, and the door bolt must be set on the side next to the construction electric elevator.

Electric elevators used in various places.Is the water cooling and air cooling of the hydraulic station the same?The entrance of each landing platform must be equipped with a landing door, and the door bolt must be set on the side next to the construction electric elevator.Home page recommendation, smooth lifting and low noise.Flat screw mechanical electric lifting mechanism: The lifting platform of this structure has the advantages of small civil engineering coordination, shallow foundation pit required, large stroke, stable operation, low noise, accurate positioning, and low cost. Adopting a horizontal screw drive and a scissor fork structure to achieve the lifting motion of the table, it can be stopped arbitrarily within the range of travel.Setting requirements: The layout and installation of all cables and wiring of electric elevators should be able to prevent mechanical damage.

The hydraulic oil enters the upper end of the hydraulic cylinder through the explosion-proof electromagnetic directional valve, and the return oil from the lower end of the hydraulic cylinder returns to the oil tank through the balance valve, hydraulic control one-way valve, throttle valve, and explosion-proof electromagnetic directional valve. To ensure a smooth descent of heavy objects and safe and reliable braking, a balance valve is installed on the return oil circuit to balance the circuit and maintain pressure, so that the descent speed does not change due to heavy objects. The throttle valve regulates the flow rate and the ascending and descending speed.Welcome calls ,Setting requirements: The quality of the standard section should meet the requirements of the product manual. Before installing the construction electric elevator, all components should be inspected, and standard sections and other components with severe wear and deformation should be replaced.The isolation and buffering rubber in various parts of the aluminum alloy electric elevator drive device are intact and tightly fitted.Setting requirements: The verticality deviation of the installation of the guide rail frame of the construction electric elevator should comply with the requirements of the user manual and specifications, as specified in the above table.Chang'an,The hydraulic oil enters the upper end of the hydraulic cylinder through the explosion-proof electromagnetic directional valve, and the return oil from the lower end of the hydraulic cylinder returns to the oil tank through the balance valve, hydraulic control one-way valve throttle valve, and explosion-proof electromagnetic directional valve. To ensure a smooth descent of heavy objects and safe and reliable braking, a balance valve is installed on the return oil circuit to balance the circuit and maintain pressure, so that the descent speed does not change due to heavy objects. The throttle valve regulates the flow rate and the ascending and descending speed.It is understood that the scissor type lifting platform is a widely used specialized equipment for high-altitude operations. Its shear fork mechanical structure provides high stability for the lifting platform, wide working platform, and high load-bearing capacity, making the range of high-altitude operations larger and suitable for multiple people working simultaneously. The lifting power is divided into V, V or V power supplies, diesel engines, using Italian and domestic hydraulic pump stations, and the table top is equipped with anti slip insulation buckle plates, which have anti slip, insulation, and safety features. Please rest assured to use.The L distance depends on the selected wall mount model.