which can save energy.Karina, square tubes are used in more and more fields. So how can we correctly choose square tubes? Next, I'll introduce the process of lower tubes.After cold drawing and aging treatment, the yield point is improved, the tensile ultimate strength is also increased, and the plasticity continues to decrease. Due to the reduction of internal stress during aging, the modulus can be basically restored. According to this principle, cold drawing or cold drawing of reinforcement or low carbon steel wire rod is often carried out on site or prefabricated component factory, so as to improve yield strength and save steel.Siquirres,The surface of galvanized square pipe treated by sand blasting, shot blasting or pickling process is relatively clean, and the oxide scale and rust are removed, which improves the adhesion of the coating. When the installation site unconditionally adopts sand blasting and shot blasting, manual and mechanical derusting can be adopted but the derusting quality level must be reached.C. special performance steel: (a) stainless and acid resistant steel; (b) Heat resistant steel; (c) Electric heating alloy steel; (d) Electrical steel; (e) High manganese wear resistant steel.Main uses of square tube: square tube is mainly used in tap water engineering, petrochemical industry, chemical industry, electric power industry, agricultural irrigation and urban construction. It is one of the key products developed.

When the vehicle is replaced with seamless square tube blank, the material is too soft to affect the requirements, so as to ensure the quality of parts and avoid wrinkles.Square tube is made of steel ingot or solid tube blank through perforation, and then made by hot rolling, cold rolling or cold drawing. Square pipe plays an important role in steel pipe industry.There are many ways of ignition, such as arc, electric spark, flame, strong current, high-temperature furnace, electron beam, laser, high-temperature radiation, microwave, chemical furnace, etc.Installation materials,The other is designed with deformation angle, which can be regarded as DEG from round tube to square tube; To & deg; The bending deformation of angle, so the deformation angle & theta; It can accurately reflect the deformation degree of corners and edges. In the design process, considering the influence of dimensional accuracy and metal work hardening, the distribution of deformation angle is usually larger at the beginning and middle passes, the fillet part of the pipe blank cannot be filled with the pass so the pass perimeter is different from that of the pipe blank. In order to ensure the dimensional accuracy, the fillet part of the pass needs to be corrected and calculated. Therefore, this method has higher design accuracy than other methods. However due to the large amount of iterative calculation, this method is more suitable for pass design by computer. If you use a frame that deforms both horizontally and vertically, you can directly use the deformation angle & theta; Pass design.The disadvantage of solid bending is that it has tensile thinning effect. The actual bending will produce tension at the bending point, and the tensile effect will shorten the longitudinal length of the bending line; The metal at the real bend will become thinner due to stretching.There are many ways of ignition, such as arc, electric spark, flame, strong current, high-temperature furnace, electron beam, laser, high-temperature radiation, microwave chemical furnace, etc.

Qb square tube qb square tube, qb square tube, QB square tube, QB square tube and hot-rolled right angle square tube are of good quality and excellent quality. We have become a supplier of many enterprises. Qb square tube and I-beam are two products with different shapes. Under the condition of the same material, the bearing capacity of steel is the same, but their uses are very different. The shape is different. Qb square tube is a cuboid, and I-beam is in I-shape. The purpose is different. I-beam can be used as span and support. Square pipe is a little worse than span. It is no problem to do support. However, the specific selection of steel depends on the requirements of the project. Square tube practical application square tube for structure (gbt-) is a square tube for general structure and mechanical structure.superior quality,Derusting: This is an important process for galvanized square pipes and components before coating, and it is the key to the quality of galvanized square pipes. Thorough derusting can improve the adhesion of antirust paint and prolong the service life of galvanized square pipe.Except for the thickening of wall thickness, the corner size and edge straightness of square pipe reach or even exceedThere are many ways of ignition, such as arc, electric spark, flame, strong current, high-temperature furnace, electron beam, laser, high-temperature radiation,KarinaCold galvanized pipe, microwave, chemical furnace, etc.Karina,Karina80 galvanized square pipe manufacturer, the service life of the saw blade. Regrinding times of the saw blade. When the saw blade is replaced, the main drive AC motor spindle rotates stepless speed change AC motor feed capacity stepless speed change feed fast return to a constant value center system brush device hydraulic saw cutting system system system represents the quality RA flatness, large burr height cutting Chip length tolerance dimension: width and length . ~ .mm ~ m ~ ~ min kW ~ rpm ( kw ~ mmmin mmmin .kw .kw & times; kW S & mu; m . mm & plusmn; mm about mm about mm about mm high. The total weight of each billet square tube is seconds (including pipe blank cutting, saw blade return, opening device, pipe blank discharge, head and tail cutting time, but excluding pipe blank transportation time). The large production capacity of the three saws is T / A. the pipe blank saw has a special reversing device (hydraulic servo device) to reduce vibration and improve the service life of the saw (only during feeding). The sawing machine has two devices distributed at the inlet and outlet (the input area is supported by roller table to ensure the bending of billet) The inlet end after sawing. Open it to ensure that the saw blade does not contact the blank when it returns. & mdash; feed saw gear & mdash; saw gear vibration reduction, which is composed of a fixed gear vibration reduction, as a movable vibration reduction to avoid the axial of the saw blade. & mdash; brush and sweep device & mdash; a driving brush and sweep device is installed at the bottom of the saw blade to clean the iron filings on the teeth and will not affect the service life of the saw blade. &Mdash; saw blade. In order to improve the service life of the saw blade, a small amount of high load agent container is atomized by air and poured on the saw blade without residue. & mdash; saw blade cooling device. A special nozzle is used to spray cold air at - oC on the saw blade. The cut-off blank is transferred to the buffer chain in front of the loader after passing through the outlet roller table and weighing device (Note: # before sawing, there is a feeding bench for single size billets that need to be cut, and after weighing, there is a feeding bench for returned billets). The buffer transfer chain transports the billets to the lower roller table of the loader. The billets are turned over from the chain to the roller table by the turnover hook. The weighed qualified billets are loaded into the annular furnace by the loader, and the weighed unqualified billets are transported from the roller table to the removal bench for removal.Strength QB square strength refers to the performance of metal materials under static load (excessive plastic deformation or fracture). Since the action modes of load include tension, compression, bending and shear, the strength is also divided into tensile strength, compressive strength, flexural strength and shear strength. There is often a certain between various strengths. Generally, tensile strength is used as the basic strength indicator. Precision pipe is a seamless pipe with high dimensional accuracy and good surface finish for mechanical structure and hydraulic equipment. The selection of precision seamless mechanical structure or hydraulic equipment can greatly save machining hours, improve material rate and improve product quality. Seamless pipe is rolled in the annular pass composed of variable cross-section circular hole groove and fixed conical plug. Cold drawing is usually carried out on single chain or double chain cold drawing machine. This method is to put the heated pipe blank in a closed cylinder, and the perforated rod and rod move to extrude the part from the smaller die hole. This method can produce steel pipe with smaller diameter.Cleaning solvent and emulsion can clean the surface of square tube to remove oil, grease, dust, agent and similar organic matter, scale, welding, so it is only used as an auxiliary means in production.